Dimplex DC10RC User manual

MODEL:
DC10RC
INSTRUCTION MANUAL
PORTABLE AIR CONDITIONER
IMPORTANT INFORMATION
Carefully read this instruction manual before you install or
use your portable air conditioner. Please retain this
manual for product warranty and for future reference.
CAUTION
even surface when operating to avoid water
leakage. explosive or corrosive atmosphere.
17°C and 43°C. For heating, only operate this unit in ambient temperatures
between 5°C and 23°C.to ensure efficient operation.
unit has been operating and is turned off,
please wait at least 3 minutes before restarting.
10. Open the adjustable air vent and extend the exhaust pipe (and drain pipe, if fitted) to
the closest window before using.
11. Only ever have a professional technician, manufacturer or service agent replace a
damaged power cord.
12. The batteries from the remote control must be removed and disposed of safely,
before the appliance is scrapped.
13. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
14. Children should be supervised to ensure that they do not play with the appliance.
Important.
The air conditioner must always be stored and
transported upright. In case of doubt we suggest you
wait for at least 24 hours before operation.
(Please keep unit upright at all times)
1. Make sure the inlet and outlet vents are never blocked.
2. Ensure the appliance is on a stable,
3. Do not operate this unit in an
4. When switched to cooling, only operate this unit in ambient temperatures between
5. Clean the air filter frequently
6. To prevent compressor damage when the
7. This unit needs to be plugged into a 220-240V ~ 50Hz AC, 10 Amp power outlet.
8. Do not use any extension cords with this unit.
9. This unit is for indoor operation only.
1

PACKAGE CONTENTS
Portable air conditioner
Remote control
Batteries for remote control
PARTS
1. Controls
2. Remote receiver
3. Adjustable air vent
4. Window kit adaptor
5. Exhaust tube
6. Upper drain plug
7. Cool air inlet
8. Cool air filter
9. Hot air inlet
10. Hot air filter
11. Lower drain plug
Note: Make sure drain plugs (6 and 11) are fitted before use.
CONTROLS AND DISPLAY
1. POWER Press the POWER button to turn the unit "ON" or "OFF".
※ The portable air conditioner is fitted with a compressor delay protection circuit. This
protects the unit from possible damage due to rapid starting and stopping of its
compressor. Compressor operation begins 3 minutes after the unit is switched on or the
mode is switched from dehumidify to air conditioning.
2. FUNCTION Press this button to select cooling, heating or dehumidification.
※ When the heating or dehumidification functions are used the upper drain plug (6) must be
removed and a drain hose must be attached.
3. TEMP+ In cooling function, this button raises the set temperature by 1°C each
time it is pressed to a maximum of 30°C. In heating function, this button
raises the set temperature by 1°C each time it is pressed to a maximum
of 25°C.
4. TEMP- In cooling function, this button lowers the set temperature by 1°C each
time it is pressed, to a minimum of 17°C. In heating function, this button
lowers the set temperature by 1°C each time it is pressed to a minimum
of 15°C.
Extendable window kit
Water tray
3
2

※ The time taken to reach the desired set temperature will depend on the environment and
the size of the space in which the unit is operating in.
For example, if the ambient temperature is too hot or the room is too large, the rate at
which the temperature descends will be slow as the cooling may be less effective.
5. DISPLAY The display indicates the current, the set temperature or the timer
setting. When the timer or temperature is adjusted, the new setting is
shown then the display returns to the current set temperature.
※ The display is also used to show error codes should a fault occur, see ERROR CODES.
6. SPEED Press SPEED to select LOW, MEDIUM, HIGH orAUTO fan speed.
If AUTO fan speed is selected, the unit operates at maximum capacity
and high fan speed while the room temperature is more than 2°C from
the set temperature. When the room temperature is within 2°C of the set
temperature, the unit operates at medium capacity and fan speed. Once
the room temperature equals the set temperature, the unit will operate
at minimum capacity and low fan speed to efficiently maintain the
desired temperature.
When HIGH, MEDIUM or LOW speed is selected, the unit operates at
maximum capacity until the set temperature is reached. The fan
operates at the selected speed.
7. TIMER ON/OFF button for the programmable timer.
The timer can be used to turn the unit on automatically after a set
time delay is complete.
1. With the unit OFF, press the "TIMER" button to set the desired time
delay before the unit is to start.
2. Choose the function desired (cooling, heating or dehumidification.)
3. Once the set time delay is complete, the unit will turn on
automatically.
4. If you press the “POWER” button before the time delay is complete,
the delay will be cancelled and the unit will turn on immediately.
1. With the unit ON, press the "TIMER" button to set the desired time
for the unit to remain on.
2. Once the set time period is complete, the unit will turn off
automatically.
3. If you press the “POWER” button before the time delay is complete,
the delay will be cancelled and the unit will turn off immediately.
8. SLEEP Press the SLEEP button to select the sleep comfort mode.
When the unit is cooling and sleep mode is selected, the unit will raise
the set temperature 1°C each hour to a maximum of 2°C over two hours.
When the unit is heating and sleep mode is selected, the unit will lower
the set temperature 1°C each hour to a maximum of 2°C over two hours.
These temperatures will be maintained for the balance of the time set
and help maximize sleep comfort.
When setting the "sleep comfort" mode, please ensure that you set the
number of hours required by using the TIMER function. The hours set
will be shown on the display by pressing either the TEMP+ or TEMP-
buttons.
The timer can be used to turn the unit off automatically after a set
time period is complete.
5
4

REMOTE CONTROL
POWER
FUNC
TIMER
AUTO
HI
MID
LOW
SLEEP
c
d
ON/OFF switch
Function selector
Timer programming
Automatic fan speed
High fan speed
Medium fan speed
Low fan speed
Sleep comfort mode selector
Raise Set Temperature
Lower Set Temperature
INSTALLATION
Unpacking the unit.
1. Remove the exhaust tube from its storage under the
rear air outlet. Replace the rear air outlet.
2. Install the exhaust tube by rotating it clockwise onto
the rear air outlet. Please ensure it is fully inserted
before use.
Locating the unit. Install the portable air conditioner in a flat location
with adequate space to ensure the air inlets and
outlets will not be blocked.
Keep a minimum clearance of 50cm from walls and
other objects. Locate the unit to allow the exhaust
pipe and drain hose to reach a suitable window, as
shown.
Avoid sharp bends or kinks in the exhaust pipe.
The optional adjustable window slider is included to
ensure the exhaust pipe is held in place (in the
window) and prevents expelled hot air re-entering
the room.
The appliance should not be used in damp areas such as a laundry or bathroom.
Do not place the unit where it will be in direct sunlight as it may overheat and turn off.
7
6

ADJUSTABLE WINDOW SLIDER KIT
The adjustable window slider kit is installed as shown below.
HEATING AND DEHUMIDIFICATION
When the heating or dehumidification functions are used the upper
drain plug (6) must be removed and a drain hose must be attached.
HEATING
When using the heating function move the rear air outlet with the exhaust tube to the front of
the unit as below:
The outlet exhaust must still be attached to the window when using the heating function.
Return the outlet and tube to the rear of the unit for cooling or dehumidification.
WATER DRAIN (Error code E4)
When the air conditioner is used, excess water condensation may be produced that cannot be
removed via the exhaust hose. This water is captured by an internal container. When this
container is full, the unit will stop working and display the E4 error code.
When the error code E4 is displayed the water collected in the internal container must be
manually drained: 1. Switch off and unplug the unit.
2. Move the unit to a suitable place to drain the water.
Consider placing a tray or suitable container under the
outlet pipe to catch the drained water.
3. Remove the lower drain plug (11), refer to parts illustration.
4. Slightly tilt the unit to the rear to drain the water.
5. Replace the drain plug.
Make sure the drain plug is re-fitted to the drain outlet before
use.
Extend the exhaust to the window before the unit is restarted.
9
8

MAINTENANCE
WARNING: ALWAYS UNPLUG THE UNIT BEFORE MOVING OR CLEANING.
CLEANING
Air filters
The air filters located on the rear of the unit can be removed simply by pulling the filter frame
slightly out and then across to the side.
Cabinet
Wipe with a damp cloth and polish with a soft cloth.
CARE OF THE UNIT
1. Only plug the unit into a suitable 220-240V~ 50Hz AC 10 AMP power supply.
2. Hold the plug when unplugging the unit, never pull on the cord.
3. Do not place the unit in direct sunlight. This can fade the plastic case.
4. Do not operate the unit in a confined space.
5. Do not place objects on top of the unit. This blocks the air outlet.
6. Do not place the unit where the air inlets or outlets may be blocked by curtains or
furniture.
7. Keep the filters clean.
OVERHEAT PROTECTION
This unit is fitted with an overheat prevention device. If the unit overheats it will automatically
turn off. The unit can be restarted after 30 minutes.
ERROR CODES
Error codes are shown on the display should a fault occur.
E1: Indicates open circuit or short circuit in the room temperature sensor.
E2: Indicates open circuit or short circuit in the pipe temperature sensor.
E3: Indicates a refrigerant leak.
Please contact an authorized service centre if any of the above error messages are
shown.
E4: Indicates the internal water container is full. Refer to WATER DRAIN.
If error code E4 persists, please contact an authorized service centre.
11
10

TROUBLE SHOOTING
Never try to repair or dismantle the air conditioner yourself. Unauthorized repairs may
result in the loss of warranty and can endanger the user and their property.
Problem Cause Solution
No power supply. Connect to a functioning power
supply socket and switch on.
Error code E4 is shown,
indicating the internal water
container is full.
Empty the internal water
container.
(Refer to WATER DRAIN)
The air conditioner
does not operate.
The start timer function is
active. Press the POWER button to deactivate the TIMER function.
The air conditioner is in direct
sunlight. Close the curtains.
Windows or doors are open. Close windows and doors.
The filters are dirty. Clean the filters.
The air inlets or outlets are
blocked. Remove the blockage.
The air conditioner
does not seem to
operate efficiently.
The room temperature is
below the set temperature. Lower set temperature.
The air conditioner
is noisy. The air conditioner is not level. Place the air conditioner on an even, solid surface.
The compressor
does not work. The overheat protection is activated. Wait 30 minutes until the temperature has decreased,
then turn the air conditioner on
again.
Note: Compressor operation
begins 3 minutes after the unit
is switched on.
The distance between the
remote control and the air
conditioner is too great.
Move closer to the air
conditioner.Aim the remote
control directly at the control
panel.
The remote control
does not function.
The batteries are flat. Replace the batteries.
If you have any issues with your unit, please contact Glen Dimplex for
your nearest service agent.
Proof of purchase is required at the time of service.
WARRANTY
The warranty period is 24 months from the date of purchase.
Glen Dimplex Australia Pty Ltd Glen Dimplex Australasia Ltd
Manukau, Auckland 2013
Ph: 1300 556 816 Ph: [phone]
Fax: [phone] Fax: [phone]
Web: www.dimplex.com.au Web: www.dimplex.co.nz
DISPOSAL
•Do not dispose of electrical appliances as unsorted municipal
waste. Use separate collection facilities.
•Contact your local government for information regarding the
collection systems available.
•If electrical appliances are disposed of in landfills or dumps,
hazardous substances can leak into the ground water, polluting the
food chain and damaging health and well-being.
13
12
38 Harris Road, East Tamaki,
Australia New Zealand
Unit 1, 21 Lionel Road.
Mount Waverley VIC 3149.

SPECIFICATIONS
Model No. DC10RC
Power Source 220-240V ~ 50Hz AC
Power Consumption
(EN14511) 1245W / 1090W
Rated Power
(EN60335) 1280W / 1100W
Cooling / Heating
Capacity 3000W / 3000W
Air Flow 360 M3/H
Moisture Removed 40 L/DAY
Refrigerant R410A
Min. room size 10m2
Max. room size 22m2
Net Weight 28KG
14
Dimensions (mm) 300W x 526D x 624H