Dimplex Xpression SP220 User manual

Pelgrim
bracket
rotated
from transit
position
fixed
socket
outlet
min.
100 495
587
180
Side
Front
300
min.
Heat
Out
Air
In
Controls
(see Fig. 6)
Viewing
Screen
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.
Dimensions
(millimetres)
Installation and Operating Instructions
Electrical
08/18802/1 Issue 1
Fig. 1
Important Safety Advice:
When using electrical appliances, basic
precautions should be followed to reduce the risk
of fire, electric shock, and injury to persons,
including the following :
•If the appliance is damaged, check
immediately with the supplier before
installation and operation.
•Do not use this heater in the immediate
surroundings of a bath, shower or swimming
pool.
•Do not use outdoors.
•This heater must not be located immediately
above or below a fixed socket outlet or
connection box.
•Do not cover or obstruct in any way the heat
outlet grille located underneath the heater.
Overheating will result if the heater is
accidentally covered.
•In the event of a fault unplug the heater.
•Unplug the heater when not required for long
periods.
•The supply cord must be placed on the right
hand side of the heater away from the heat
outlet underneath the heater.
•Although this heater complies with safety
standards, we do not recommend its use on
deep pile carpets or on long hair type of rugs.
•Do not leave young children, the elderly, or
the infirm unsupervised in the vicinity of the
heater.
•The appliance must be positioned so that the
plug is accessible.
•If the supply cord is damaged it must be
replaced by the manufacturer or service agent
or similarly qualified person in order to avoid
a hazard.
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the
voltage marked on the heater must correspond to the supply
voltage.
Do not switch the appliance on until properly installed. Please
read all the safety warnings and operating instructions.
Unpack the heater carefully and retain the packaging for
possible future use, in the event of moving or returning the
fire to your supplier.
Contents of Carton.
•SP2 Heater.
•Wall fixing bracket.
•Three fixing screws and three wall plugs.
•Remote control and batteries (3 AAA’s type).
•Spare bulb.
Do not connect the heater to an electricity supply until it is
installed on a wall correctly. - see ‘Installation’.
A choice of 1kW or 2kW heat output is provided by the fan
heater, which is concealed underneath the unit.
The heater can be used remotely or manually. - see
‘Operation’.
General features of remote control are:
•Heat output can be increased or decreased
according to your particular requirements.
•The illumination of fuel effect can be increased or
decreased.
•Programmable timer.
Please note: Used in an environment where background
noise is very low, it may be possible to hear the fan which
operates the flame effect. This is normal and should not be
a cause for concern.
General
Xpression Wall fire SP2
Model No: SP220

ensure ledge
at back of
fire engages
wall bracket
c
Detail '1'
ledge
wall
bracket
alift appliance
above wall
fixing bracket
rotate bottom
fixing bracket
down from its
transit position
slide down over
bracket, ensure
that ledge of
appliance engages
behind wall
bracket and is
central
bring level
with wall
d
wall bracket
b
see
detail '1'
wall fixing
bracket
screws
wall
plugs
wall
holes
Installation
Recommended Fixing Dimensions - Fig. 2
Fig. 3
Fig. 5
Mark the bottom hole position (see Fig. 5), remove the heater
ensuring that the bottom fixing bracket is rotated up.
Drill and fit wall plug.
Refit the heater to the wall fixing bracket (i.e. follow steps as
in Fig. 4 a,b,c and d above) and rotate the bottom fixing
bracket down again and use the screw provided to
permanently fix the heater in place.
The heater should not be connected until the instruction leaflet
is read fully.
Do not connect appliance until properly fixed to the wall
and the Instruction leaflet is read fully.
This model is designed to be permanently fixed to a wall at a
minimum height of 300mm.
The wall bracket must be fitted horizontally with the cable
routed to the bottom right of the heater as in Fig 1.
A height of 600mm from bottom of heater to floor is
recommended for optimum viewing of fuel bed (see Fig. 2
for recommended fixing dimensions).
For optimum viewing mark the top two screw fixing positions
on wall in accordance with the recommended fixing
dimensions - see Fig. 2.
Fix the wall bracket using the two plugs and screws provided
- see Fig 3.
Carefully lift the heater up ensuring that the top rear ledge of
heater engages the wall bracket and is sitting centrally
positioned. - see Fig 4 (b).
Rotate the bottom fixing bracket down. - see Fig 4 (c).
Gently bring the heater level with the wall. - see Fig 4 (d).
120
outline of
wall fire
526
120
240
13
600
1113
513
outline of wall
fixing bracket
Fig. 4
outline of
wall fire
mark hole
centre with
pencil

outline of
wall fire
Neon's for
indicating
operation
level
(1kW/2kW) Heat
(Switch 3)
Manual Controls
Dimmer
(Switch 4)
Manual/Automatic
(Switch 2)
Standby (ON/OFF)
(Switch 1)
MAN.
AUTO
OFF
ON
Manual Operation
The Standby Switch (Switch 1) must be first turned ‘ON’ and
the AUTO/MAN (Switch 2) switch set to ‘MANUAL’ to operate
the manual controls - see Fig 6.
Note : When the fire is put in Manual mode the first time the
flame effect will come on indicated by the Bottom neon coming
on for 3 seconds - see Fig 7.
Setting Operation Indication
Flame Effect Bottom Neon
Flame Effect & 1Kw Heat Press the ‘ I ’ button (Switch 3) Middle Neon
Flame Effect & 2Kw Heat Press the ‘ I ’ button again (Switch 3) Top Neon
To go to the previous settings press the ‘ O‘ button (Switch
3).
To increase or decrease the brightness of the flames, use
the dimmer button (Switch 4). You can have any setting
between full brightness and the flames totally off. The heat
setting will remain the same.
To turn off the power the Standby Switch (Switch 1) must be
turned ‘OFF’.
Note : Every time that manual mode is selected the previous
light and heat settings come on automatically.
Fig. 6
Fig. 7

Remote Control Operation
LCD display
The LCD display shows the following functions:
•Main menu points: OFF, FLAME, HEAT, TEMP, TIMER,
PROG, and TIME.
•Brightness of the flame effect shown as a bar chart in 4
steps (50 steps internally).
•Remote control set temperature in °C (thermostat
function).
•Room temperature in °C .
•Selectable heat settings LOW HEAT, HIGH HEAT.
•Time display in format hh:mm – shown as 24hr.
•Weekdays MON, TUE, WED, THU, FRI, SAT, SUN.
Menu functions
•OFF switching off of all functions (stand-by mode).
•FLAME switching on the flame effect from 0 (off) to
50 (max. brightness).
•HEAT setting the desired heat position from 0 (off)
to 2 (max. heat setting).
•TEMP preselection of the remote control set
temperature from 5°C to 35°C.
•TIMER selection of the run back timer function (from
1 minute to 4 hours 59 minutes). When the selected time
is over the unit will be in stand-by mode.
•PROG selection of the programming mode. 32
individual programs can be entered. This is a week timer
where all functions of the unit can be checked time
controlled.
•TIME setting the time and the weekdays.
First steps
•Fit batteries supplied.
•Press switch 1 to ON (see Fig. 6).
•Press switch 2 to AUTO (see Fig. 6)
The remote control is now ready.
General
The remote control consists of 5 control buttons and a LCD
display with a visible area of 40x40mm.
The maximum range of use for the remote control is 15metres.
LCD Display Fig. 8
Operating Instructions
•Switching ON/OFF
The heater can be switched on by pressing the enter !or
!"buttons.
The heater can be switched off by moving the cursor to the
OFF menu item.
•Flame brightness
Navigate the cursor to FLAME with the !"buttons. Press
!--
--
-to change the brightness of the fire effect from off (0) to
maximum (50).
•Heat settings
Navigate the cursor to HEAT with the !"buttons. Press !
--
--
-to change the heat setting between off/low heat/maximum
heat.
Note: If the room temperature is higher than the remote
control set temperature located on the left side of LCD display,
heat will not come on (see Thermostat operation below).
•Thermostat
Navigate the cursor to TEMP with the !"buttons. Press !
--
--
-to set the desired remote control set temperature between
5°C and 35°C and press enter !. When the room tempera-
ture is higher than the remote control set temperature,
the heater switches off automatically until the room tempera-
ture falls below the remote control set temperature.
•Runback timer
Navigate the cursor to TIMER with the !"buttons. Set the
hours (0 to 4) with !
--
--
-and press enter !. Then set the
minutes (0 to 59) with ! --
--
-and press enter !. Now the
runback timer is activated (the symbol TIMER appears) and
will switch the heater off automatically when the pre-set time
is over.
•Time setting
Navigate the cursor to TIME with the !"buttons. Press the
enter button !to adjust the weekday with the !
--
--
-buttons.
Confirm with the enter button !and set the hours and minutes
with ! --
--
-. Press enter !or "to leave the time menu.
•Program mode
1. Navigate the cursor to PROG with the !", buttons and
press enter . Choose a program number between 1 and
32 with the !
--
--
- buttons and press enter !.
2. Set the days with ! --
--
-. Single days, Monday until Friday,
Saturday and Sunday or Monday until Sunday can be
chosen. Press the enter button !to accept.
3. Set the program start time with ! --
--
-and confirm the
hours and minutes with the enter button !.
4. Set the program stop time with ! --
--
-and confirm the
hours and minutes with the enter button !.
5. Set the remote control set temperature with ! --
--
-and
confirm with the enter button !.
6. Set the brightness of the fire effect with ! --
--
-from 0 to
50 and confirm with the enter button !.
7. Set the heat setting between off/low heat/maximum heat
with the ! --
--
-button and confirm with the enter button !.
8. All settings for the first program are done now. Enter a
new program according to the steps 1-8 or activate the
already entered program by leaving of this menu with
the !button.
9. Now the program mode is active, the symbol PROG
appears. The heater operates according to the entered
information. While the program mode is activated, the
start and stop time, the active program number and the
remote control set temperature and the room temperature
will be displayed alternating.

Replacing the remote control
The new remote control must be set up as follows:
Press switch 1 to ON .
Press switch 2 to AUTO (see Fig. 6).
Press switch 3 to Ofor more than 3 seconds until all three
LED’s are on (see Fig. 7).
Press the remote control’s enter button or the !"buttons.
Now the heater has learned the serial number from the
remote control and will work with this remote control only
(this procedure is repeatable many times).
General information
1. In case that the remote control is out of order or the
batteries need replacing the fire will stop automatically after
3 minutes.
2. If the batteries are changed the programme memory
remains but the time has to be set (see Time setting).
10. An entered program can be checked, edited and deleted
just by navigating again into the PROG menu and
pressing the enter button. With the !--
--
-buttons the
different program numbers can be selected. To delete
one program number, press the "button. The CP symbol
(clear program) appears and by pressing the enter button
!the current program will be deleted. !"leaves the
menu without deleting the program.
Important Battery information.
Discard leaky batteries.
Dispose of batteries in the proper manner according to
Provincial and local regulations. Any battery may leak
electrolyte if mixed with a different battery type, if inserted
incorrectly, if all the batteries are not replaced at the same
time, if disposed of in a fire or if an attempt is made to
charge a battery not intended to be recharged.

remove two
screws to take
out fuel effect
2
1
fuel effect
retaining
bracket
fuel effect
bracket
channel
aremove two
fixing screws
carefully tilt
forward the
front window
assembly, and
then lift upwards
with both hands
to remove front
b
The front window assembly will need to be removed in order
to change lamps.
Warning! The front window assembly is heavy and easily
damaged !.
The front window assembly is fixed with two screws on top
and is supported underneath by the chassis.
Care is needed to avoid the assembly falling forward while
removing the screws see Fig. 9.
To gain access to lamps please apply the following
procedure :
Remove the two screws which hold the front window
assembly in place.
While holding the assembly by its sides with both hands,
carefully tilt forwards and then lift up and out - see Fig. 9.
Place the front window assembly flat on a protective surface
such as a matt with the glass facing away from the floor.
Remove two screws securing fuel effect. Holding the log
carefully lift up (1) and out (2) - see Fig. 10.
Carefully slide the flexible rotisserie to one side ensuring that
the rubber grommet is not lost – see Fig. 11.
WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE REMOVING LAMPS.
Lamp Replacement
Fig. 10
Fig. 11
grommet
rotate flexible
rotisserrie out
of position
axial
bracket
Fig. 9

rotate bulbs
to remove
Detail 'A'
see detail 'A'
rotisserrie
Remove the defective lamp by unscrewing it (see Fig. 12).
Replace with a 60W E14 SES Clear Candle bulb, rotating it.
Take care not to over-tighten the lamp.
Steps for reassembling the heater
1. Refit the rotisserie making sure that the rubber
grommet is carefully pushed into the slotted hole on the axial
bracket (see Fig. 11).
2. Refit the fuel effect ensuring that the fuel effect bracket
on the fuel effect slots in between the fuel effect retaining
bracket and the inner glass (see Fig. 10).
3. Refit the window assembly (ensuring that its base is
held in place i.e. that it slots into the channel on the frame
(see Fig. 10) reversing the steps as outlined previously.
Fig. 12

After Sales Service
Your appliance is guaranteed for one year from the date of
purchase. We undertake to repair or exchange free of charge
within this period, any part with the exception of a lamp found
to be defective due to a manufacturing fault.
Your rights under this guarantee are additional to your
statutory rights, which in turn are not affected by this
guarantee.
Please retain your receipt as proof of purchase.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use
abrasive cleaners. The glass viewing screen should be
cleaned carefully with a soft cloth. DO NOT use proprietary
glass cleaners.
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility
(EMC) EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336
Glen Dimplex UK Limited
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire. SO30 2DF
UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)
Customer Services: Tel. [phone]
Fax. [phone]
e-mail customer[email protected]
Republic of Ireland Tel. [phone]