DINOTWIN Hydro T2 User manual

USER GUIDE
DINOTWIN
DINOTWIN HYDRO T2 SPORT BLUETOOTH WIRELESS STEREO HEADSET
Accessories
Fit Setup
Pairing
Fit Clip
Controller Buttons
02
04
06
10
18
Index
Accesories
Insuring quality audio requires the right fit.
Orientation of the Buds
A simple way to know which ear bud
belongs to which ear is the left ear bud
has an “L” on the left outer side and the
right has an “R” on the outer side.
Another way is that whatever
side the controller is on, is the Right
side.
The DinoTwin T2 Hydro’s accessory
packet contain a pair of small, medium,
and large ear gels, as well as universal
ear stabilizers, to accommodate any user,
small or large. Take your time finding the
right sized ear bud and ear stabilizer
combination; we strongly recommend
using a mirror starting out.
The DinoTwin T2’s have two ways to pair (connect) to your cell phone
or Bluetooth device. Traditional Pairing or NFC Pairing. The next few
pages will walk you through this important process; using either
method. Before this process, we strongly recommend charging the
ear buds for a solid two hours.
Once plugged in, you will notice the LED light turn a solid red, once
this turns off, they are fully charged and ready to start the pairing
with your cell phone or Bluetooth music device.
Pairing with cell phone or Bluetooth device
R
02
04 05
03
L M
Ear Gels
Ear Stabilizers
S

Traditional Pairing
Ear Stabilizer
Ear Gels
NFC Pairing
As with Traditional Pairing, make sure Bluetooth is
enabled on your phone, as well as NFC. Simply turn
on the headset by pressing the button on the
controller and in standby mode (powered on, but
not connected to a device). On the Right ear bud
you will see the NFC logo, touch or tap that on the
NFC location on your phone, a prompt will appear
stating “Connecting to Dino Twin T2”, to discon-
nect touch or tap again on the same location, then
just power down the headset.
Activate the Bluetooth option on your phone. Press and hold the
button on the controller for 8 seconds until the LED light flashes red
and blue rapidly (the LED is under the Right bud). Now go to your
Bluetooth menu on your phone and select "Search", "Dino Twin T2"
should appear, select it and hit "Pair" (0000 is the password if
prompted for one). Once paired, to power down the ear buds,
press the button for 4 seconds. To power on,
hold the button for 4 seconds and they will
automatically connect to the last device paired
with.
The ear stabilizer does just what the
name suggests; whether it is jogging
or a tough workout routine, you need
stability. As mentioned before, using a
mirror may help the first few times to
adjust the ear stabilizers for the
optimal fit.
Detailed Instructions and Information
Getting the right fit doesn’t just stop at the ear stabilizer; the correct
set of ear gels are equally as important. Ear gels not only help
preventing the ear buds from falling out; they help ensure a secure
seal keeping the music in and the noise out. The DinoTwin T2’s come
packaged with 3 different sizes – small, medium, and large. We
encourage you to try all three sizes, and if needed, mix them up, for
example, should the medium fit nicely on the right side but not the left,
try the large ear gel on the left.
y
06
08
11
09
Fit Clip
The Fit Clip has 2 functions. One is to
secure the ear buds around your neck
should you take them off and. The Fit
Clip’s other function is to tighten the
cord behind your head as shown on the
next page.
Using this method, keep in mind that the
microphone is located on the controller, and
will be further from your mouth. Using the
Fit Clip to tighten the cable behind your
head may may affect voice calls.
10
07

15
14
16
18
20
17
19
21
What’s Included Charging
Pairing with multiple bluetooth devices
Controller Buttons
Music Commands Additional Information
Phone Commands
DinoTwin T2 Hydro Bluetooth Headphones
DinoTwin Carrying Case
3 Pairs of Ear Gels (S,M,& L)
1 Pair of Universal Ear Stabilizers
USB Charging Cable
Instruction Manual
Charge for approximately 2 hours for
8 hours of continuous usage. Should
the Red LED start to blink, this
indicates low battery and approxi-
mately 15 minutes left of usage. If
using with an iPhone, you will see an
icon with the amount of battery
power left in the headset.
The multi-pair function is factory disabled; you must enable this feature
prior to pairing with more than one device. While the device is in
Standby Mode (Bluetooth is powered on, just not connected to any
device), press and hold the and buttons until you hear four
ascending tones.
Simply have the Bluetooth paired to at least one device already, now
power down the Bluetooth headset, turn back on the Bluetooth entering
back into pairing mode (if needed see page 6), pair with the second
device.
There are only 3 buttons on the controller, familiarizing them and their
functionality is important.
Here are some additional tips that may answer some questions. When
using the headset, though you may have increased the volume to the
max from the phone/music device, there may be some extra volume by
also increasing the volume from the headset itself, and vice verse when
decreasing volume. Also, in some cases when finding the right fit, using
a mirror, twist the buds into your ear with the stabilizer on to make
sure the stabilizer is where it should be, it can make all the difference.
For other frequently asked questions, please visit our website at
www.dinotwin.com/support.
When listening to music, to increase the volume, tap the button, and
to lower the volume tap the button. To skip to the next track, short
press the button, to skip to the previous track, short press the
button, to pause, press the button once, and to play press the
button again.
Press the button to answer a call while listening to music (you will
hear personalized ring tone from the headset), then short press the
button to end the call and it will automaicatlly resume to playing your
music.
* Not all mobile phones support all the functions listed above. Please refer to your cell phone’s user manual.
Answering a phone call, short press the button. While on the call,
press the button to increase the volume, or press the button to
decrease the volume, and short press the button to end the call.
To mute the conversation, press the button for 2 seconds, to take
the call off mute, simply press the button again for 2 seconds.
To Voice Dial, simply short press the and button, and to redial the
last number double click the button.
The three buttons are:
Up/Volume +/Previous Track, etc
Down/Volume -/Forward Track, etc
Answer/End/Pair/Pause, etc
This process can be continued for up to 8 devices. Once the
phone/music device is paired, there will be no need to pair again; all that
is needed is that you select the headset from your phone or music
device.
To turn this feature this off, which is recommended if only using with
one Bluetooth device, press and hold the and buttons while in
standby mode until you hear four descending tones.
USER MANUAL

22 23
Specifications Warranty, Care, and Maintenance
Full warranty, care and maintenance available at dinotwin.com/support Copyright 2014
DinoTwin, LLC. All Rights Reserved. DinoTwin and the DinoTwin logos are trademarks of DinoTwin,
LLC. Bluetooth is a trademark owned by Bluetooth SIG, Inc. USA. iPhone is a trademark of Apple,
Inc., registered in the USA and other countries.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful operation, and (2) this device must accept
any interference received, including interference that may cause undesired operation. Any
changes or modifications to device will void the user’s authority to operate the device. Do not
dispose of the battery in fire, may cause explosion.
Bluetooth version
Bluetooth profiles
Operating distance
Standby time
Headset charging time
Weight
* Operating distance is approx. 10 meters but may vary due to obstacles, radio signals,
locations where radio interference occurs, magnetic fields from microwave ovens, and/or
device sensitivity.
Please visit us at
dinotwin.com
Bluetooth v4.0
Headset, Hands free, AVRCP, & A2DP
10 meters *
200 hours
2 hours
13 g