Dinstar DPA User manual

DPA Quick Installation Guide
Shenzhen Dinstar Co., Ltd.
Address: Floor 18, Building 7A, Vanke Cloud City Phase 1, Xingke 1st Street, Xili Sub-district,
Nanshan District, Shenzhen.
Postal Code: 518052
Telephone: [phone]
Fax: [phone]
Email：sales @dinstar.com
Website：www.dinstar.com

Content
1. Packing List....................................................................................................................3
2. Material Specification ...................................................................................................3
3. Installation.....................................................................................................................5
4. Get the device IP address.............................................................................................5
5. DPA Configuration.........................................................................................................6
Log in the Device Web GUI................................................................................................6

1. Packing List
Paging
Gateway
Accessories
Installation
diagram
2. Material Specification
Device Dimension
115*85*30mm
Front Panel

（Picture I）
Item
Description
1
Ethernet interface: Standard RJ45 interface, 10/100M adaptive, it is recommended to use category 5 or
super category 5 network cable
2
Camera network interface: external webcam can be connected to realize video call
3
Network status indication. No flash: no network connection. Slow flash: the network connection is
normal. Fast flash: the SIP account has been registered successfully
4
External audio signal input, external background sound source can be connected
5
It can be connected to an external recorder to output the mixed signal of both sides of the intercom
6,8
Increase or decrease the volume. You can hear the change of ring tone in idle time. You can directly
control the volume during a call
7
TF card slot
9
Long press to restore the default configuration of the device
10
Power indication
Rear Panel
（Picture II）
Item
Description
1
The grounding terminal shall be grounded in case of sound interference;
2
USB port, which can be connected to USB flash disk

3
The power amplifier output interface can be externally connected to a passive speaker. Maximum
output power 36W (corresponding to DC24V DC input)
4
Audio output port, can also be externally connected to the power amplifier
5
Microphone input port
6
The short-circuit input interface can be used to directly control the short-circuit output interface or the
input interface of other security equipment
7
DC12V / 24 output interface
8
Power socket, DC 12v-24v
9
External LED indication interface
10
Speed dial key interface
11
Short circuit switch output interface (normally open)
3. Installation
1. The equipment is fixed by 4 screws.
(Picture III）（Picture IV）
4. Get the device IP address
After device connect to the power supply, default way to get IP address is DHCP. Press DSS1 key continuously for
10 seconds, and the device will broadcast its IP address.

5. DPA Configuration
Log in the Device Web GUI
To input the device IP on the web browser. (for example:input http://172.28.4.131）,and then entry the log in
interface, default account: admin, default password: admin )
Configure SIP Account
To configure SIP account, Active, register name, username password, SIP server address & port, then submit.

To configure device parameter
1. 1. Set up speed dial.
During daytime dialing, you can set up to three numbers. Cycle dialing. If the first number is not connected, the device
will automatically dial other numbers and cycle call attempts; One night number can be set. If the current time is
night, the device will automatically dial this number.
2. Short circuit output switch configuration
The output switch working mode, monostable mode or bistable mode, and the switch closing time in monostable
mode can be set.
3. Control the short-circuit output switch through DTMF.

On this page, you can set the control of short-circuit output switch through DTMF after the call is connected.
Shenzhen Dinstar Co.,Ltd
Add: Floor 18, Building 7A, Vanke Cloud City Phase 1, Xingke 1st Street, Xili Sub-district, Nanshan District, Shenzhen, P.R.
China 518000
TEL：[phone] FAX：[phone]
www.dinstar.com