DIODE LED TOUCHDIAL Mini User manual

1 OF 3 IG070319-2.0
TOUCHDIAL
™
Mini Remote Dimmer INSTALL GUIDE
®TOUCHDIAL™Mini Remote Dimmer
INSTALLATION GUIDE
1. Only for use with compatible 12V and 24VDC constant voltage
luminaires.
2. This product is rated for indoor installation and is not protected
against moisture.
3. Do not modify product beyond instructions or warranty will be
void.
SAFETY & WARNINGS
QUICK SPECS / MODELS
DI-RF-REM-DIM-1
FRONT BACK
TOOLS FOR INSTALL
APPROVED LED LUMINAIRES
The TOUCHDIAL Wall Paddle Dimmer is compatible with all
Diode LED 12V and 24VDC single color constant voltage tape
lights and xtures.
ADDITIONAL TOUCHDIAL COMPONENTS
Phillips-head
screwdriver
V−
V+
V+
W
B
G
R
®
TOUCHDIAL
™
Receiver
DATA IN/OUT
V−
D1+
GND
V+
V+
V+
OUTPUT TOLOAD
POWER
INPUT
LEARNINGKEY
WW
WW
CW
CW
W
W
W
W
D1─
D2+
D2─
MASTER COMPANION
DI-RF-REC-CV-A
TOUCHDIAL Receiver, or
DI-RF-REC-CV-SC
TOUCHDIAL Mini Receiver
(Required)
Input Operating Frequency Dimensions
3V (CR2025) Bat-
tery (Included) 869.5/916.5/434MHz 1.5 x 0.5 in. (D x H)
CR2025 Baery
DI-RF-REC-CV-SC
®
TOUCHDIAL MINI RECEIVER
V−
V+
V+
V−
POWER
INPUT
OUTPUT
TOLOAD
PUSH SWITCH
V+
V−
LearningKey
DRY LOCATION
24VDC
12VDC

2 OF 3 IG070319-2.0
TOUCHDIAL
™
Mini Remote Dimmer INSTALL GUIDE
TOUCHDIAL™Mini Remote Dimmer
INSTALLATION GUIDE
V−
V+
V+
W
B
G
R
®
TOUCHDIAL™ Receiver
RECEIVER REPEATER
DATA IN/OUT
V−
D1+
GND
V+
V+
V+
OUTPUT
TO LOAD
POWER
INPUT
LEARNINGKEY
WW
WW
CW
CW
W
W
W
W
D1─
D2+
D2─
V+
V−
L
N
GND
SYNCING INSTRUCTIONS
INSTALL TOUCHDIAL RECEIVER SYSTEM
LED Driver TOUCHDIAL Receiver LED Luminaire
SYNC TOUCHDIAL CONTROL TO MASTER
RECEIVER
V−
V+
V+
W
B
G
R
®
TOUCHDIAL™ Receiver
D
ATA IN/OUT
V−
D1+
GND
V+
V+
V+
OUTPUT TO LOAD
POWER
INPUT
LEARNING KEY
WW
WW
CW
CW
W
W
W
W
D1─
D2+
D2─
MASTER
COMPANION
1. Short press Power/Brightness button on Controller.
2. Short press LEARNING KEY button on TOUCHDIAL MASTER
receiver.
3. Short Press the Power/Brightness button on the Mini Remote
Dimmer.
Luminaire will ash to indicate pairing.
Refer to TOUCHDIAL Receiver Installation Guide.
OPERATION
BATTERY REPLACEMENT
1. Open Battery backplate on
Remote.
2. Insert new battery.
V−
V+
V+
W
B
G
R
®
TOUCHDIAL™ Receiver
D
ATA IN/OUT
V−
D1+
GND
V+
V+
V+
OUTPUT TO LOAD
POWER
INPUT
LEARNING KEY
WW
WW
CW
CW
W
W
W
W
D1─
D2+
D2─
MASTER
COMPANION
Jumper
Header
COMPANION MASTER
SYNCING NOTE
When syncing the TOUCHDIAL Mini Remote Dimmer, the
1st receiver must be set to the MASTER function as outlined
below. See the TOUCHDIAL Receiver Installation Guide for
more thorough information.
Short press to turn
ON/OFF.
Hold to increase or
decrease brightness.
LOOKING FOR SYSTEM DIAGRAMS?
See the TOUCHDIAL RECEIVER (DI-RF-REC-CV-A) or
TOUCHDIAL Mini Receiver (DI-RF-REC-CV-SC) Installation
guide for SOLID COLOR system diagrams.
V−
V+
V+
W
B
G
R
®
TOUCHDIAL™ Receiver
DATA IN/OUT
V−
D1+
GND
V+
V+
V+
OUTPUT
TO LOAD
POWER
INPUT
LEARNING KEY
WW
WW
CW
CW
W
W
W
W
D1─
D2+
D2─
MASTER COMPANION
CR2025 Baery
DI-RF-REC-CV-SC
®
TOUCHDIAL MINI RECEIVER
V−
V+
V+
V−
POWER
INPUT
OUTPUT
TO LOAD
PUSH SWITCH
V+
V−
Learning Key
1
2
3
1
2

3 OF 3
®Toll Free: 877.817.6028 | Fax: [phone] | www.DiodeLED.com | [e-mail]
© 2019 Elemental LED, Inc. All rights reserved. Specicaons are subject to change without noce.
IG070319-2.0TOUCHDIAL
™
Mini Remote Dimmer INSTALL GUIDE
TOUCHDIAL™Mini Remote Dimmer
INSTALLATION GUIDE
MOUNTING
1. Place Base Mount on
surface where desired,
ensuring it is level.
2. Screw Mount to surface
using included Screws.
3. Place Remote into
Mount.
Symptom Common Cause
Control won’t
function
• Check for dead batteries.
• Remote must be turned on for
operation.
Master receiver
does not sync
with remote
• Ensure function is set to MASTER
(1 pin) - See Syncing Note or
TOUCHDIAL Receiver Installation
Guide.
• If still not syncing do following: 1)
Turn off main power to receiver and
turn back on. 2) Reset receiver by
long pressing LEARNING KEY for 5
seconds until LED ashes. 3) Re-sync
receiver to control.
TROUBLESHOOTING
See TOUCHDIAL Receiver Install Guide for more troubleshooting tips.
TOUCHDIAL MINI REMOTE DIMMER SPEC SHEET
For full specications.
TOUCHDIAL RECEIVER SPEC SHEET & INSTALL
GUIDE
For full specications and installation instructions.
ADDITIONAL RESOURCES
1. Place Remote and Base
onto a metal surface.
The included Magnet
will hold the Dimmer in
place.
MAGNETIC MOUNT
SCREW MOUNT
a
b