Directed Electronics Valet 561T User manual

MMooddeell556611TT
IInnssttaallllaattiioonnGGuuiiddee
© 2005 Directed Electronics—Vista, CA N561T 07-05

22© 2005 Directed Electronics—all rights reserved
ttaabblleeooffccoonntteennttss
Code Hopping™, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Routine™, Nite-Lite®,
Nuisance Prevention® Circuitry, Revenger®, Silent Mode™, Soft Chirp®, Stinger®, Valet®, Vehicle
Recovery System®, VRS®, and Warn Away® are all Trademarks or Registered Trademarks of
Directed Electronics.
wwhhaattiissiinncclluuddeedd................................................33
wwaarrnniinngg!!ssaaffeettyyffiirrsstt.............
.............................44
iinnssttaallllaattiioonnppooiinnttssttoorreemmeemmbbeerr..........................55
ffiinnddiinnggtth
heewwiirreessyyoouunneeeedd..................................66
finding the starter wire . . . . . . . . . . . . . . . . 6
obtaining constant 12V . . . . . . . . . . . . . . . . 6
finding the accessory wire. . . . . . . . . . . . . . . 7
finding the 12V switched ignition wire . . . . . . 7
finding the tachometer wire . . . . . . . . . . . . . 8
finding a (+) parking light wire . . . . . . . . . . . 8
finding the wait-to-start bulb wire for diesels . 9
pprriimmaarryyhhaarrnneessss((HH11))wwiirriinnggddiiaaggrraamm...........
.......1100
44--ppiinnssaatteelllliitteehhaarrnneessssddiiaaggrraamm..........................1100
hheeaavvyyggaauuggeerreellaayywwiirriinnggddiiaaggr
raamm......................1111
ddoooorrlloocckkhhaarrnneessss,,33--ppiinnccoonnnneeccttoorr....................1111
rreemmootteessttaarrtthhaar
rnneessss((HH22))wwiirriinnggddiiaaggrraamm............1111
pprriimmaarryyhhaarrnneessss((HH11)),,99--ppiinnccoonnnneeccttoorr................1122
hheeaavvy
yggaauuggeerreellaayyiinntteerrffaaccee..............................1166
rreemmootteessttaarrtthhaarrnneessss((HH22)),,55--ppiinnccoonnnneeccttoorr...
.......1177
nneeuuttrraallssaaffeettyysswwiittcchhiinntteerrffaaccee..........................1188
pre-1996 dodge dakota pickups with . . . . . . .
2.5 liter motors . . . . . . . . . . . . . . . . . . . . . 20
general motors trucks, SUVs, and column . . . .
shifting passenger cars . . . . . . . . . . . . . . . . 20
bbyyppaassssiinnggGGMMvveehhiicclleeaannttii--tth
heeffttssyysstteemmss((VVAATTSS))....2211
11999955aannddnneewweerrvveehhiicclleeaannttii--tthheeffttssyysstteemmss..........
((iimmmmoobbiilliizzeerrss))..................................................2222
passlock I and passlock II (PL-1 and PL-2) . . 22
passkey III (PK-3), transponder-based systems22
ooppttiioonnaallaannttii--ggrriinnddrreellaayy............................
......2233
iinntteerrnnaallpprrooggrraammmmiinnggjjuummppeerr............................2244
light flash (+)/(-) . . . . . . . . . . . . . . . . . . . 24
tach threshold on/off . . . . . . . . . . . . . . . . . 24
pplluugg--iinnpprrooggrraammsswwiittcchh....................................2255
ttaacchhlleeaarrnniinngg..................................................2255
to learn the tach signal . . . . . . . . . . . . . . . 25
ooppe
erraattiinnggsseettttiinnggsslleeaarrnnrroouuttiinnee........................2266
ffeeaattuurreessmmeennuu...............................
...................2277
ffeeaattuurreeddeessccrriippttiioonnss..........................................2288
rreeaarrddeeffooggggeer
rccoonnttrrooll........................................3311
ttiimmeerrmmooddee.......................................
...............3311
ssaaffeettyycchheecckk....................................................3322
ttrroouubblleesshhoooottiinng
g................................................3333
wwiirriinnggqquuiicckkrreeffeerreenncceegguuiiddee.....................
.........3355

© 2005 Directed Electronics—all rights reserved 33
wwhhaattiissiinncclluuddeedd
■TThheeccoonnttrroollmmoodduullee((sseeeeddiiaaggrraamm))
■TThheepplluugg--iinnpprrooggrraammsswwiittcchh
■AAhhooooddppiinnsswwiittcchh
■AAttoogggglleeoovveerrrriiddees
swwiittcchh
6-pin relay output
4-pin satellite/
harness
9-pin main harness
5-pin remote start
harness
not used
2-pin BLUE
program plug
status LED
not used

44© 2005 Directed Electronics—all rights reserved
wwaarrnniinngg!!ssaaffeettyyffiirrsstt
The following safety warnings must be observed at all times:
■Due to the complexity of this system, installation of this product must only be performed by an authorized
Directed Electronics dealer.
■When properly installed, this system can start the vehicle via a command signal from the remote control
transmitter. Therefore, never operate the system in an area that does not have adequate ventilation. The fol-
lowing precautions are the sole responsibility of the user; however, authorized Directed Electronics dealers
should make the following recommendations to all users of this system:
1. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).
2. When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote
start system must be disabled using the installed toggle switch.
3. It is the user's sole responsibility to properly handle and keep out of reach from children all remote
control transmitters to assure that the system does not unintentionally remote start the vehicle.
4. TTHHEEUUSSEERRMMUUSSTTIINNSSTTAALLLLAACCAARRBBOONNMMOONNOOXXIIDDEEDDEETTEECCTTOORRIINNOORRAABBOOUUTTTTHHEELLIIVVIINNGGAARREEAAAADDJJAACCEENNTTTTOO
T
THHEEVVEEHHIICCLLEE..AALLLLDDOOOORRSSLLEEAADDIINNGGFFRROOMMAADDJJAACCEENNTTLLIIVVIINNGGAARREEAASSTTOOTTHHEEEENNCCLLOOSSEEDDOORRPPAARRTTIIAALLLLYY
EENNCCLLOOSSEEDDVVEEHHIIC
CLLEESSTTOORRAAGGEEAARREEAAMMUUSSTTAATTAALLLLTTIIMMEESSRREEMMAAIINNCCLLOOSSEEDD..
■Use of this product in a manner contrary to its intended mode of operation may result in property damage,
personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1)
Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the
keys in the ignition. The user will be responsible for having the neutral safety feature of the vehicle period-
ically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be
performed by an authorized Directed Electronics dealer in accordance with the Safety Check outlined in this
product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult
with the user to fix the problem immediately.
■After the remote start module has been installed, test the remote start module in accordance with the Safety
Check outlined in this installation guide. If the vehicle starts when performing the Neutral Safety Shutdown
Circuit test, the remote start unit has not been properly installed. The remote start module must be removed
or properly reinstalled so that the vehicle does not start in gear. All installations must be performed by an
authorized Directed Electronics dealer. OOPPEERRAATTIIOONNOOFFTTHHEERREEMMOOTTEESSTTAARRTTMMOODDUULLEEIIFFTTHHEEV
VEEHHIICCLLEESSTTAARRTTSSIINN
GGEEAARRIISSCCOONNTTRRAARRYYTTOOIITTSSIINNTTEENNDDEEDDMMOODDEEOOFFOOPPEERRAATTIIOONN..OOPPEERRAATTIINNGGTTHHEERREEMMOOTTEESSTTAARRTTSSYYSST
TEEMMUUNNDDEERR
TTHHEESSEECCOONNDDIITTIIOONNSSMMAAYYRREESSUULLTTIINNPPRROOPPEERRTTYYDDAAMMAAGGEEOORRPPEERRSSOONNAALLIINNJJUURRYY..IIMMMMEEDDIIAATTEELLYYCCEEAASSEETTHHEEUUS
SEE
OOFFTTHHEEUUNNIITTAANNDDRREEPPAAIIRROORRDDIISSCCOONNNNEECCTTTTHHEEIINNSSTTAALLLLEEDDRREEMMOOTTEESSTTAARRTTMMOODDUULLEE..DDIIRREECCTTEEDDEELLEECCTTRROONNIICCSS
WWIILLLL
NNOOTTBBEEHHEELLDDRREESSPPOONNSSIIBBLLEEOORRPPAAYYFFOORRIINNSSTTAALLLLAATTIIOONNOORRRREEIINNSSTTAALLLLAATTIIOONNCCOOSSTTSS..

© 2005 Directed Electronics—all rights reserved 55
iinnssttaallllaattiioonnppooiinnttssttoorreemmeemmbbeerr
IIMMPPOORRTTAANNTT!!This product is designed for fuel-injected, automatic transmission vehicles only.
Installing it in a standard transmission vehicle is dangerous and is contrary to its intended use.
BBeeffoorreebbeeggiinnnniinnggtthheeiinnssttaallllaattiioonn::
■Please read this entire installation guide before beginning the installation. The installation of this remote
start system requires interfacing with many of the vehicle’s systems. Many new vehicles use low-voltage or
multiplexed systems that can be damaged by low resistance testing devices, such as test lights and logic
probes (computer safe test lights). Test all circuits with a high quality digital multi-meter before making con-
nections.
■Do not disconnect the battery if the vehicle has an anti-theft-coded radio. If equipped with an air bag, avoid
disconnecting the battery if possible. Many airbag systems will display a diagnostic code through their
warning lights after they lose power. Disconnecting the battery requires this code to be erased, which can
require a trip to the dealer.
■Remove the dome light fuse. This prevents accidentally draining the battery.
■Roll down a window to avoid being locked out of the vehicle.
AAfftteerrtthheeiinnssttaallllaattiioonn::
■Test all functions. The "Using Your System" section of the Owner's Guide is very helpful when testing.
■Complete the vehicle
Safety Check outlined in this manual prior to the vehicle reassembly.

66© 2005 Directed Electronics—all rights reserved
ffiinnddiinnggtthheewwiirreessyyoouunneeeedd
IIMMPPOORRTTAANNTT!!Do not use a 12V test light or logic probe (computer safe test light) to locate these
wires! All testing described in this manual assumes the use of a digital multimeter.
We recommend two possible sources for 12V constant: The (+) terminal of the battery, or the constant 12V supply
to the ignition switch. Always install a fuse within 12 inches of this connection. If the fuse will also be power-
ing other circuits, such as door locks, a power window module, or a Nite-Lite® headlight control system, fuse
accordingly.
IIMMPPOORRTTAANNTT!!Do not remove the fuse holder on the red wire. It ensures that the control module
has its own fuse, of the proper value, regardless of how many accessories are added to the main
power feed.
The starter wire provides 12V directly to the starter or to a relay controlling starter. In some vehicles, it is
necessary to power a cold start circuit. A cold start circuit will test exactly like a starter circuit, but it does not
control the starter. Instead, the cold start circuit is used to prime the fuel injection system for starting when the
vehicle is cold.
HHoowwttooffiinnddtthheessttaarrtteerrwwiirreewwiitthhyyoouurrmmuullttiimmeetteerr::
1. Set to DCV or DC voltage (12V or 20V is fine).
2. Attach the (-) probe of the meter to chassis ground.
3. Probe the wire you suspect of being the starter wire. The steering
column is an excellent place to find this wire. Remember you do not
need to interrupt the starter at the same point you test it. Hiding
your starter kill relay and connections is always recommended.
4. Turn the ignition key switch to the start position. Make sure the car
ffiinnddiinnggtthheessttaarrtteerrwwiirree
oobbttaaiinniinnggccoonnssttaanntt1122VV

© 2005 Directed Electronics—all rights reserved 77
is not in gear! If your meter reads (+)12V, go to the next step. If it doesn’t, probe another wire.
5. Cut the wire you suspect of being the starter wire.
6. Attempt to start the car. If the starter engages, reconnect it and go back to Step 3. If the starter does not
turn over, you have the right wire.
The ignition wire is powered when the key is in the run or start position. This is because the ignition wire powers
the ignition system (spark plugs, coil) as well as the fuel delivery system (fuel pump, fuel injection computer).
Accessory wires lose power when the key is in the start position to make more current available to the starter motor.
HHoowwttooffiinndd((++))1122VViiggnniittiioonnwwiitthhyyoouurrmmuullttiimmeetteerr::
1. Set to DCV or DC voltage (12V or 20V is fine).
2. Attach the (-) probe of the meter to chassis ground.
3. Probe the wire you suspect of being the ignition wire. The steering
column harness or ignition switch harness is an excellent place to find
this wire.
4. Turn the ignition key switch to the run position. If your meter reads
(+)12V, go to the next step. If it does not read (+)12V, probe another wire.
5. Now turn the key to the start position. The meter display should stay
steady, not dropping by more than a few tenths of a volt. If it drops close
to or all the way to zero, go back to Step 3. If it stays steady at (+)12V, you have found an ignition wire.
An accessory wire will show (+)12V when the key is in the accessory and run positions. It will not show (+)12V
during the cranking cycle. There will often be more than one accessory wire in the ignition harness. The correct
accessory wire will power the vehicle's climate control system. Some vehicles may have separate wires for the
blower motor and the air conditioning compressor. In such cases, it will be necessary to add a relay to power the
second accessory wire.
ffiinnddiinnggtthheeaacccceessssoorryywwiirree
ffiinnddiinnggtthhee1122VVsswwiittcchheeddiiggnniittiioonnwwiirree

88© 2005 Directed Electronics—all rights reserved
Most vehicles use a (+) parking light circuit. The (+) parking light wire is often found near the light switch. In
many vehicles the light switch is built into the turn signal lever; in these vehicles the parking light wire can be
found in the steering column. The same wire can often be accessed in the kick panel or running board.
NNOOTTEE::Many Toyotas and other Asian vehicles, send a (-) signal from the switch to a relay. The
relay then sends (+)12V to the bulbs. Whenever you have difficulty finding a (+) parking light
wire near the switch, simply test the wires at any switch or control panel that is lit by the instru-
ment panel lighting. Remember, you need a (+) parking light wire that does not vary with the
dimmer setting.
HHoowwttooffiinnddaa((++))ppaarrkkiinngglliigghhttffllaasshhwwiirreewwiitthhyyoouurrmmuullttiimmeetteerr::
1. Set to DCV or DC voltage (12V or 20V is fine).
2. Attach the (-) probe of the meter to chassis ground.
3. Probe the wire you suspect of being the parking light wire. Usually, the area near the headlight/parking light
switch is an excellent area to start, as is the kick panel.
4. Turn on the parking lights. If your meter shows (+)12V, turn off the parking lights and make sure it goes back
to zero.
5. If it does return to zero, turn the parking lights back on and, using the dash light dimmer control, turn the
brightness of the dash lights up and down. If the meter changes more than a volt when using the dimmer,
look for another wire. If it stays relatively close to (+)12V, you have found your parking light wire.
NNOOTTEE::Vehicles that use a (-) signal from the switch to the factory relay may be interfaced
directly. (See H1/5 WHITE wire of Primary Harness (H1) Wire Connection Guide section.)
To test for a tachometer wire, a multimeter capable of testing AC voltage must be used. The tachometer wire will
show between 1V and 6V AC. In multi-coil ignition systems, the system can learn individual coil wires. Individual
coil wires in a multi-coil ignition system will register lower amounts of AC voltage. Also, if necessary, the system
ffiinnddiinnggtthheettaacchhoommeetteerrwwiirree
ffiinnddiinnggaa((++))ppaarrkkiinngglliigghhttwwiirree

© 2005 Directed Electronics—all rights reserved 99
can use a fuel injector control wire for engine speed sensing. Common locations for a tachometer wire are the
ignition coil itself, the back of the gauges, engine computers, and automatic transmission computers.
IIMMPPOORRTTAANNTT!!Do not test tachometer wires using a test light or logic probe. The vehicle will be
damaged.
HHoowwttooffiinnddaattaacchhoommeetteerrwwiirreewwiitthhyyoouurrmmuullttiimmeetteerr::
1. Set to ACV or AC voltage (12V or 20V is fine).
2. Attach the (-) probe of the meter to chassis ground.
3. Start and run the vehicle.
4. Probe the wire you suspect of being the tachometer wire with the red probe of the meter.
5. If this is the correct wire the meter will read between 1V and 6V.
In diesel vehicles it is necessary to interface with the wire that turns on the WAIT-TO-START light in the dash-
board. This wire illuminates the bulb until the vehicle’s glow plugs are properly heated. When the light goes out
the vehicle can be started. This wire is always available at the connector leading to the bulb in the dashboard.
It can also be found at the Engine Control Module (ECM) in many vehicles.
TTootteessttaannddddeetteerrmmiinneetthheeppoollaarriittyyoofftthhiissw
wiirree::
1. Set your multimeter to DCV or DC voltage (12 or 20V is fine).
2. Attach the (+) probe of the meter to (+)12V.
3. Probe the wire that you suspect leads to the bulb with the (-) probe of the meter.
4. Turn the ignition switch to the ON position.
5. If the meter indicates 12 volts until the light goes out you have isolated the correct wire and the wire's polar-
ity is negative (ground while the bulb is on).
6. If the meter reads zero volts until the light goes out and then reads 12 volts, you have isolated the correct
wire and the wire's polarity is positive.
ffiinnddiinnggtthheewwaaiitt--ttoo--ssttaarrttbbuullbbwwiirreeffoorrddiieesseellss

1100© 2005 Directed Electronics—all rights reserved
pprriimmaarryyhhaarrnneessss((HH11))wwiirriinnggddiiaaggrraamm
______
______
______
______
______
______
______
______
______
44--ppiinnssaatteelllliitteehhaarrnneessssddiiaaggrraamm
______
______
______
______ PPIINNKKIIGGNNIITTIIOONNTTRRIIGGGGEERR
PPUURRPPLLEESSTTAARRTTEERRTTRRIIGGGGEERR
OORRAANNGGEEAACCCCEESSSSOORRYYTTRRIIGGGGEERR
BBLLUUEESSTTAATTUUSSOOUUTTPPUUTT
11
22
33
44
WWHHIITTEE((++//--))LLIIGGHHTTFFLLAASSHH
BBLLAACCKKGGRROOUUNNDD
RREEDD//WWHHIITTEENNOOTTUUSSEEDD
WWHHIITTEE//RREEDD((++))AACCTTIIVVAATTIIOONNIINNPPUUTT
GGRRAAYY//BBLLAACCKK((--))WWAAIITTTTOOSSTTAARRTTIINNPPUUTT
WWHHIITTEE//BBLLUUEE((--))AACCTTIIVVAATTIIOONNIINNPPUUTT
YYEELLLLOOWW((++))IIGGNNIITTIIOONNOOUUTT((TTOOAALLAARRMM))
GGRREEEENN//WWHHIITTEEFFAACCTTOORRYYRREEAARRMM
LLIIGGHHTTGGRREEEENN//BBLLAACCKKFFAACCTTOORRYYDDIISSAARRMM
HH11//11
HH11//22
HH11//33
HH11//44
HH11//55
HH11//66
HH11//77
HH11//88
HH11//99

© 2005 Directed Electronics—all rights reserved 1111
hheeaavvyyggaauuggeerreellaayywwiirriinnggddiiaaggrraamm
______
______
______
______
______
______
ddoooorrlloocckkhhaarrnneessss,,33--ppiinnccoonnnneeccttoorr
______
______
______
NNoottee::Refer to TechTip 1041 for wiring information.
rreemmootteessttaarrtthhaarrnneessss((HH22))wwiirriinnggddiiaaggrraamm
______
______
______
______
______ BBLLUUEE//WWHHIITTEE((--))220000mmAA22NNDDSSTTAATTUUSS//RREEAARRDDEEFFOOGGGGEERROOUUTTPPUUTT
GGRRAAYY((--))HHOOOODDPPIINNSSWWIITTCCHHSSHHUUTTDDOOWWNNWWIIRREE
BBRROOWWNN((++))BBRRAAKKEESSWWIITTCCHHSSHHUUTTDDOOWWNNWWIIRREE
VVIIOOLLEETT//WWHHIITTEETTAACCHHOOMMEETTEERRIINNPPUUTTWWIIRREE
BBLLAACCKK//WWHHIITTEE((--))NNEEUUTTRRAALLSSAAFFEETTYYSSWWIITTCCHHIINNPPUUTT
HH22//11
HH22//22
HH22//33
HH22//44
HH22//55
BBLLUUEE((--))UUNNLLOOCCKKOOUUTTPPUUTT
EEMMPPTTYYNNOOTTUUSSEEDD
GGRREEEENN((--))LLOOCCKKOOUUTTPPUUTT
11
22
33
RREEDD((++))((3300AA))HHIIGGHHCCUURRRREENNTT1122VVIINNPPUUTT
PPIINNKK//WWHHIITTEE((++))PPRROOGGRRAAMMMMAABBLLEEOOUUTTPPUUTTFFOORRAACCCCEESSSSOORRYYOORRIIGGNNIITTIIOONN
RREEDD((++))((3300AA))HHIIGGHHCCUURRRREENNTT1122VVIINNPPUUTT
OORRAANNGGEE((++))((3300AAMMPP))OOUUTTPPUUTTTTOOAACCCCEESSSSOORRYYCCIIRRCCUUIITT
PPUURRPPLLEE((++))((3300AAMMPP))OOUUTTPPUUTTTTOOSSTTAARRTTEERRCCIIRRCCUUIITT
PPIINNKK((++))((3300AAMMPP))OOUUTTPPUUTTTTOOIIGGNNIITTIIOONNCCIIRRCCUUIITT
11
22
33
44
55
66

1122© 2005 Directed Electronics—all rights reserved
pprriimmaarryyhhaarrnneessss((HH11)),,99--ppiinnccoonnnneeccttoorr
This wire sends a negative pulse every time the remote start is activated or the doors are unlocked. This can be
used to pulse the disarm wire of the vehicle's factory anti-theft device. Use a relay to send a (-) or (+) pulse to
the disarm wire as shown in the following diagrams.
RReellaayyffoorrNNeeggaattiivvee((--))DDiissaarrmmWWiirreeRReellaayyffoorrPPoossiittiivvee((++))DDiissaarrmmWWiirree
This wire sends a negative pulse every time the remote start shuts down or the doors are locked. This can be
used to pulse the arm wire of the vehicle's factory anti-theft device. Use a relay to send a (-) or (+) pulse to the
arm wire.
AAssaannaadddd--oonnttooaannaafftteerrmma
arrkkeettsseeccuurriittyyssyysstteemm::If connected, disconnect the ignition/accessory input of the
remote controlled security or keyless entry system. Connect the H1/3 YELLOW ignition output to the
ignition/accessory input of the remote controlled security or keyless entry system. The wire will prevent the host
system from sensing that the ignition is on during remote start operation.
HH11//33YYEELLLLOOWW((++))iiggnniittiioonnoouuttppuuttttooRRFFssyysstteemm
HH11//22GGRREEEENN//WWHHIITTEEffaaccttoorryyrreeaarrmm
HH11//11LLIIGGHHTTGGRREEEENN//BBLLAACCKK((--))ffaaccttoorryysseeccuurriittyyddiissaarrmm

© 2005 Directed Electronics—all rights reserved 1133
This input comes from the factory set to 2 activation pulses. This means that it is necessary to have 2 consecu-
tive ground pulses on the white/blue wire for the remote start to activate or to deactivate.
NNOOTTEE::When the activation pulse count can be programmed to 1, 2, or 3 pulses.
Connect this wire to the wire in the vehicle that sends the signal to turn on the WAIT-TO-START bulb in the dash-
board. In most diesels the wire is negative (ground turns on the bulb) and the GRAY/BLACK can be directly
connected to the wire in the vehicle. If the vehicle uses a positive wire (12V to turn on the bulb) a relay must
be used to change the polarity. (See
Finding the Wires You Need section for testing procedures.) Here are some
common colors of this wire:
■Chevrolet and GMC trucks: Light Blue or Dark Blue
■Ford Trucks: Black/Pink
■Dodge Ram Trucks: Orange/Black or Black/Orange
NNOOTTEE!!A 1-amp diode must be installed in line on the factory wire between the wait-to-start indi-
cator and the ECM. (See the following diagram for details.)
HH11//55GGRRAAYY//BBLLAACCKK((--))ddiieesseellwwaaiitt--ttoo--ssttaarrttbbuullbbiinnppuutt
HH11//44WWHHIITTEE//BBLLUUEE((--))rreemmootteessttaarrttaaccttiivvaattiioonniinnppuutt

1144© 2005 Directed Electronics—all rights reserved
This input comes from the factory set 2 activation pulses. This means that it is necessary to have 2 consecutive
12V pulses on the white/blue wire for the remote start to activate or to deactivate.
NNOOTTEE::When the activation pulse count can be programmed to 1, 2, or 3 pulses.
Remove any paint and connect this wire to bare metal, preferably with a factory bolt rather than your own screw.
(Screws tend to either strip or loosen with time.) We recommend grounding all your components to the same
point in the vehicle.
HH11//88BBLLAACCKK((--))cchhaassssiissggrroouunnddccoonnnneeccttiioonn
HH11//66WWHHIITTEE//RREEDD((++))aaccttiivvaattiioonniinnppuutt

© 2005 Directed Electronics—all rights reserved 1155
IIMMPPOORRTTAANNTT::Do NOT connect this wire to a negative vehicle light flash wire before changing the
programming jumper to the negative polarity position or damage to the vehicle light circuit may
occur.
As factory configured, the H1/9 WHITE wire should be connected to the (+) parking light wire. If the light flash
polarity jumper is moved to the (-) position (refer to the Programming Jumper section of this guide), this wire
then supplies (-) 200mA output. This is suitable of driving the light control (-) circuits in Toyota, Lexus, BMW
some Mitsubishi, some Mazda, and other models.
NNOOTTEE::For parking light systems that draw 10 amps or more, the jumper must be placed to the
(-) light flash output (refer to the Programming Jumpers section of this guide. P/N 8617 or a
standard automotive SPDT relay must be used on the H1/2 light flash output wire.
((++))PPoossiittiivveeLLiigghhttFFllaasshhOOuuttppuutt
((--))LLiigghhttFFllaasshhOOuuttppuutt
HH11//99WWHHIITTEE((++//--))lliigghhttffllaasshhoouuttppuutt

1166© 2005 Directed Electronics—all rights reserved
hheeaavvyyggaauuggeerreellaayyiinntteerrffaaccee
The heavy gauge wires are used to energize high current circuits in the vehicle. It is crucial that these connec-
tions are made correctly so that they are capable of handling the current demands. For this reason, scotch locks,
T-taps and other such connectors should not be used.
Remove the two 30 amp fuses prior to connecting these wires and do not replace them until the satellite has
been plugged into the control module. These wires are the source of current for all the circuits the relay satel-
lite will energize. They must be connected to a high current source. Since the factory supplies (+) 12V to the key
switch that is used to operate the motor, it is recommended that these wires be connected there.
NNOOTTEE::If the factory supplies two separate (+) 12V feeds to the ignition switch, connect one RED
wire of the satellite to each feed at the switch.
Connect this wire to the ignition wire in the vehicle. (See Finding the Wires You Need section of this guide.)
Connect this wire to the accessory wire in the vehicle that powers the climate control system. (See
Finding the
Wires You Need
section of this guide.)
Connect this wire to the starter wire in the vehicle. (See
Finding the Wires You Need section of this guide.)
Connect this wire to the second ignition or accessory wire in the vehicle. (Selectable user menu features.)
NNOOTTEE::For vehicles that do not have a second ignition wire, this connection is not required.
PPIINNKK//WWHHIITTEE((++))oouuttppuuttttoosseeccoonnddiiggnniittiioonn//aacccceessssoorryycciirrccuuiitt
PPUURRPPLLEE((++))ssttaarrtteerroouuttppuutt
OORRAANNGGEE((++))aacccceessssoorryyoouuttppuutt
PPIINNKK((++))iiggnniittiioonnoouuttppuutt
RREEDD((22))((++))1122VViinnppuuttffoorrrreellaayyss

© 2005 Directed Electronics—all rights reserved 1177
rreemmootteessttaarrtthhaarrnneessss((HH22)),,55--ppiinnccoonnnneeccttoorr
Connect this wire to the toggle (override) switch as shown in Figure A. Connect the other wire from the toggle switch
to the PARK/NEUTRAL switch in the vehicle. This wire will test with ground with the gear selector either in PARK or
NEUTRAL. This will prevent the vehicle from accidentally being started while in a drive gear. This input MUST rest at ground
in order for the remote start system to operate. Connected properly the vehicle will only start while in PARK or NEUTRAL.
In some vehicles, the PARK/NEUTRAL position switch activates a factory starter lock-out that will not allow the
starter to operate in a drive gear. In these vehicles, connect this wire to the toggle switch as shown in Figure B.
Connect the other wire from the toggle switch to chassis ground.
FFiigguurreeAAFFiigguurreeBB
IIMMPPOORRTTAANNTT!!Always use the Vehicle Safety Check section of this guide to verify that the vehicle
cannot be started in ANY drive gear and that the override switch is functioning properly.
This input provides the module with information about the engine's revolutions per minute (RPMs). It can be con-
nected to the negative side of the coil in vehicles with conventional coils. In multi-coil and high energy ignition
systems locating a proper signal may be more difficult. (See
Finding the Wires You Need section of this guide for
finding the tachometer wire.) Once connected, you must teach the system the tach signal. (See
Tach Learning
section of this guide.)
This wire MUST be connected to the vehicle's brake light wire. This is the wire that shows (+) 12V when the brake
pedal is depressed. The remote start will be disabled or shut down any time the brake pedal is depressed.
HH22//33BBRROOWWNN((++))bbrraakkeesswwiittcchhiinnppuutt
HH22//22VVIIOOLLEETT//WWHHIITTEEttaacchhoommeetteerriinnppuutt
HH22//11BBLLAACCKK//WWHHIITTEEnneeuuttrraallssaaffeettyysswwiittcchhiinnppuutt

1188© 2005 Directed Electronics—all rights reserved
This wire MUST be connected to the hood pinswitch. This input will disable or shut down the remote start when
the hood is opened.
This wire supplies a 200mA output as soon as the module begins the remote start process. The H2/5 BLUE/WHITE
wire can also be used to activate the defogger trigger (latched/pulsed) 10-seconds after the remote start
engages. (See the
Feature Descriptions section in this guide for details about programming this output.)
nneeuuttrraallssaaffeettyysswwiittcchhiinntteerrffaaccee
Some vehicles combine the column shift mechanism and the mechanical neutral safety switch into one mechan-
ical part. In these vehicles, it is impossible to interface the remote start system before the neutral safety switch.
With this type of vehicle, if the vehicle is left in a drive gear and the remote start system is activated, the vehicle
will move and may cause damage to persons or property.
According to available information, vehicles known to be manufactured this way are most General Motors trucks,
sport utility vehicles and column shifting passenger vehicles. Available information also indicates that pre-1996
Dodge Dakota pickups with 2.5 liter motors are also manufactured this way.
GM vehicles that have the neutral safety switch built into the column shifter can usually be identified by a purple
starter wire. Typically, vehicles that use an outboard mechanical switch use a yellow wire from the ignition switch
to the mechanical switch and a purple wire from the mechanical switch to the starter itself. Remember, this is
only a rule of thumb and is not intended as a substitute for proper testing.
IIMMPPOORRTTAANNTT!!Please see vehicle Safety Check section of this guide for testing procedures.
Vehicles with the neutral safety switch built into the column shifter require that the shifter be placed in park in
order to remove the keys from the ignition. As a result, it is possible to use the key-in-ignition sense switch to
prevent remote starting if the keys are in the ignition. (See
General Motors Trucks, SUVs and Column-Shifting
Passenger Cars
and Pre-1996 Dodge Dakota Pickups with 2.5 Liter Motors diagrams in this section on how to
accomplish this.) The first diagram applies to all General Motors vehicles as of the date of this guide’s publica-
tion. The second diagram applies to all pre-1996 Dodge Dakota pickup trucks with 2.5 liter motors. This solution
has one side effect: If the customer inserts the key in the ignition with the driver's door open, the remote start
system will shut down. If this interface is used, it is important to inform the customer that the driver’s door must
be closed before inserting the key into the ignition when the remote start is active. This will allow the customer
to turn the key on and shut the remote start down by pressing the brake, without the key sense wire shutting
HH22//55BBLLUUEE//WWHHIITTEEssttaattuuss//ffaaccttoorryysseeccuurriittyyrreeaarrmmoouuttppuutt
HH22//44GGRRAAYY((--))hhooooddppiinnsswwiittcchhiinnppuutt

© 2005 Directed Electronics—all rights reserved 1199
down the unit prematurely.
You must also connect the H2/4 BROWN (+) shut-down input to the yellow wire on the relay satellite
ribbon cable. This prevents the remote start system from activating if the key is left in the “run” position. You
must use diodes to isolate the ignition circuit from the brake switch circuit as shown in the diagram below.
IIMMPPOORRTTAANNTT!!Once the interface is complete, attempt to remote start the vehicle with the door
closed and the key in the ignition. The vehicle should not start. If it does, re-check the
connections.
As of the date of this guide’s publication, the following list describes the types of vehicles that are known to
have a mechanical neutral safety switch instead of an electrical neutral safety circuit. The model years will vary
from vehicle to vehicle. This list will be updated periodically as new information is available; installers are
encouraged to call DIRECTED Technical Support at 1-800-753-0800 with updated information.
■Pre-1996 Dodge Dakota pickups with 2.5 liter engines
■GM "B" Platform: Caprice, Impala SS and Roadmaster
■GM "D" Platform: Cadillac Fleetwood and Fleetwood Brougham
■GM "P" Series: Commercial Van
■GM "L/M" Series: Astro, Safari
■GM "C/K" Series: Full-size pickup, Sierra, Suburban, Tahoe, Yukon
■GM "S/T" Series: Blazer, Bravada, Jimmy, pickup, Sonoma
■GM "G" Series: Express, Savanah
YELLOW WIRE ON
RELAY SATELLITE
RIBBON CABLE
(+) BRAKE WIRE
IN VEHICLE
BROWN (+)
SHUTDOWN INPUT
1N4004 DIODE
1N4004 DIODE
DIA-154

2200© 2005 Directed Electronics—all rights reserved
pprree--11999966ddooddggeeddaakkoottaappiicckkuuppsswwiitthh22..55lliitteerrmmoottoorrss
ggeenneerraallmmoottoorrssttrruucckkss,,SSUUVVss,,aannddccoolluummnnsshhiiffttiinnggppaasssseennggeerrccaarrss