Directed XpressKit DBALL User manual

Vehicle Application Guide................................................................................................................................................
Installation
Type 1a (with CHTHD1 T-Harness R7)..........................................................................................................................
Type 1b (with CHTHD1 T-Harness R1-R6)....................................................................................................................
Type 1c (without T-Harness)..........................................................................................................................................
Type 2a (with CHTHD1 T-Harness R7)..........................................................................................................................
Type 2b (with CHTHD1 T-Harness R1-R6)....................................................................................................................
Type 2c (without T-Harness)..........................................................................................................................................
Type 3a (with CHTHD2 T-Harness R9)..........................................................................................................................
Type 3b (with CHTHD2 T-Harness R1-R6)....................................................................................................................
Type 3c (without T-Harness)..........................................................................................................................................
Type 4..............................................................................................................................................................................
Type 5..............................................................................................................................................................................
Programming
Module Programming - Vehicles WITH Factory Keyless................................................................................................
Module Programming - Vehicles WITHOUT Factory Keyless........................................................................................
Module Reset..................................................................................................................................................................
Hard Reset.......................................................................................................................................................................
Feature & Option List.......................................................................................................................................................
Feature Programming......................................................................................................................................................
LED Diagnostics & Troubleshooting................................................................................................................................
Limited One-Year Consumer Warranty............................................................................................................................
Quick Reference Guide...................................................................................................................................................
02
03
04
05
07
08
09
11
12
13
15
17
19
20
21
21
22
23
24
25
26
Index
Installation Guide
Update Alert: Firmware updates are posted to the web on a regular basis. We recommend
that you check for firmware and/or install guide updates prior to installing this product.
Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
Door lock/convenience and override firmware for most Chrysler, Dodge, Jeep and Volkswagen vehicles.
Covers the CAN type (most CAN type vehicles starting in 2004).
The optional Plug & Play T-Harnesses CHTHD1 and CHTHD2 (sold separately) provide simpler and
faster installation.
® Chrysler, Dodge, Jeep and Volkswagen are registered trademarks and property of their respective companies.

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
Vehicle Application Guide Page 2
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year
allows you to determine which installation type should be used for your vehicle.
* To select the proper install type, locate the ignition switch connector and select your install type as illustrated below:
OR
Type 4 vehicles have a
(+) Starter wire at pin 4
of the ignition switch
(+) Starter wire in pin 4
1
Connector side view at ignition switch
5 or 6
Type 3 vehicles do not
have a (+) Starter wire
at the ignition switch
Pin 4 empty
1
Connector side view at ignition switch
5 or 6
Vehicles
2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 PK-Immobilizer Bypass-Data No Key Req'd AV-Parking Lights Control CC-Heated Seats Activation DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Sliding Door Control Driver DL-Sliding Door Control Passenger DL-Trunk / Hatch Release FOB-Control of aftermarket alarm with OEM remote RS-RAP Shut Down (Retained ACC Power) RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin SS-Entry Monitoring Trunk/Hatch Pin ST-Brake Status (foot brake) ST-E-Brake Status
Chrysle r
200 3 3 3 3 • • • • • • • D • D • • D • • •
300/300c 2 2 2 • W • • • • • • D • D • • D • • •
300/300c 4 4 4 • • • • • • • • D • D • • D • • •
Aspen 3 3 3 • • • • • • • D • D • • D • • •
PT Cruiser 4 4 4 4 4 • • • • • • D • D • • D • • •
Sebring 3 3 3 3 • • • • • • • D • D • • D • • •
Sebring Convertible 3 3 3 • • • • • • • D • D • • D • • •
Sebring Sedan 3 3 3 3 • • • • • • • D • D • • D • • •
Town & Country 1 1 1 1 1 1 1 1 • W • • • • • • • • D • D • • D • • •
Dodge /Ra m
1500 1 1 • W • • • • • D • D • • D • •
2500 1 1 • W • • • • • D • D • • D • •
3500 1 1 • W • • • • • D • D • • D • •
Avenger 3 3 3 3 3 3 3 • • • • • • • D • D • • D • • •
C/V 1 1 1 1 • W • • • • • • • • D • D • • D • • •
Caliber 3 3 3 3 3 3 or 4* • • • • • • D • D • • D • • •
Caravan 1 1 1 • W • • • • • • • • D • D • • D • • •
Challenger 1 1 1 1 1 1 1 • W • • • • • • D • D • • D • • •
Challenger (Smart Key) 1 1 1 1 1 1 1 • W • • • • • • D • D • • D • • •
Charger 2 2 2 • W • • • • • • D • D • • D • • •
Charger 4 4 • • • • • • • • D • D • • D • • •
Dakota 3 3 3 3 3 • • • • • • D • D • • D • •
Dakota 4 4 • • • • • • D • D • • D • •
Durango 1 1 1 • W • • • • • D • D • • D • • •
Durango 3 3 3 • • • • • • D • D • • D • • •
Durango 5 5 5 • • • • • • D • D • • D • • •
Grand Caravan 1 1 1 1 1 1 1 1 • W • • • • • • • • D • D • • D • • •
Journey 1 1 • • • • • • D • D • • D • • •
Magnum 2 • W • • • • • D • D • • D • • •
Magnum 4 4 4 • • • • • • • • D • D • • D • • •
Nitro 3 3 3 3 3 • • • • • • D • D • • D • • •
RAM 1 1 • W • • • • • D • D • • D • •
RAM 3 3 3 or 4* • • • • • • D • D • • D • •
Je e p
Commander 2 2 2 4 4 • • • • • • • D • D • • D • • •
Compass 3 3 3 3 3 3 3 3 3 • • • • • • D • D • • D • • •
Grand Cherokee 1 1 1 • W • • • • • D • D • • D • • •
Grand Cherokee 2 2 2 • • • • • • D • D • • D • • •
Grand Cherokee 4 4 4 • • • • • • • D • D • • D • • •
Grand Cherokee (Sm art K ey ) 1 1 1 • W • • • • • D • D • • D • • •
Liberty 3 3 3 3 3 • • • • • • D • D • • D • • •
Patriot 3 3 3 3 3 3 3 3 3 • • • • • • D • D • • D • • •
W rangler 3 3 3 3 3 3 3 3 3 • • • • • • D • D • • D • • •
Mitsubishi
Raider 3 3 3 • • • • • • D • D • • D • •
Raider 5 • • • • • • D • D • • D • •
Vol ksw a ge n
Routan 1 1 1 1 1 • W • • • • • • • • D • D • • D • • •
Legend:
•: D2D & Wire-to-Wire (W2W)
W: Wire-to-Wire
AV: Horn & Lights Controls
PK: Transponder & Immobilizer Override
CC: Comfort & Convenience Control
RS: Remote Start & Engine Controls
DL: OE Door Lock & Alarm Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
Installation Type 1a (with CHTHD1 T-Harness R7)
Remote
Starter
(+) Ignition Input/Output
10
DBALL/
DBALL2
RF
Prog. Button
LED
[2] (+) Parking Light Output
4
TX
(-) Ground
RX
(+)12V
14 12 2
P#: XKD2D65
Page 3
(+) 12V(+) 12V
(-) Hood Switch(-) Hood Switch
(-) Ground(-) Ground
[2] Connection only required for Dodge Journey.
Parking
Lights
Connect for Dodge
Journey only.
See page 6 for
wiring information
CHTHD1 R7
(optional)
Ignition
Barrel
(vehicle side)
This is the only connection required for parking
light output for the Dodge Journey, and the
DBALL MUX connection is not required.
OR
Wires not listed in this diagram are not required for the installation.
12-pin Connector
(Vehicle side)
12-pin Connector
(harness side)
12-pin Connector
(harness side)
(-) Driver door trigger
Violet wire in
driver kick panel
Do NOT
connect
Remote Start Safety
Override Switch is inactive
(used for RSR only)
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[1] (AC) Tach Input
RAP Off: Yellow/Black: 10
(MUX) Parking Lights: Violet/Green: 8
(MUX) Parking Lights: Violet/Brown: 9
[1] (AC) Tach Output: Violet/White: 5
All adapters are displayed from the wire side (unless specified otherwise).
Pink
D2D
only

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
Installation Type 1b (with CHTHD1 T-Harness R1-R6)
Remote
Starter
(+) Ignition Input/Output
10
DBALL/
DBALL2
RF
Prog. Button
LED
[2] (+) Parking Light Output
4
TX
(-) Ground
RX
(+)12V
14 12 2
P#: XKD2D65
Page 4
(+) 12V(+) 12V
(-) Hood Switch(-) Hood Switch
(-) Ground(-) Ground
[2] Connection only required for Dodge Journey.
Connect for Dodge
Journey only.
See page 6 for
wiring information
CHTHD1 R1-R6
(optional)
Ignition
Barrel
(vehicle side)
Connect to White/Red wire, pin 3
This is the only connection required for parking
light output for the Dodge Journey, and the
DBALL MUX connection is not required.
OR
Wires not listed in this diagram are not required for the installation.
12-pin Connector
(Vehicle side)
12-pin Connector
(harness side)
12-pin Connector
(harness side)
(-) Driver door trigger
Violet wire in
driver kick panel
Do NOT
connect
Remote Start Safety
Override Switch is inactive
(used for RSR only)
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[1] (AC) Tach Input
RAP Off: Yellow/Black: 10
(MUX) Parking Lights: Violet/Green: 8
(MUX) Parking Lights: Violet/Brown: 9
[1] (AC) Tach Output: Violet/White: 5
All adapters are displayed from the wire side (unless specified otherwise).
D2D
only
Parking
Lights

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
Ignition
Barrel
Installation Type 1c (without T-Harness)
Remote
Starter
1
6
12 7
Connector side view
at ignition switch
(-) GWR (Status)
(+) Ignition Input/Output
(-) Lock Output
(+) Starter Output
(-) Unlock Output
(-) Trunk Output
(-) Aux1 Right Sliding Door
(-) Aux2 Left Sliding Door
(+) Parking Lights Output [2]
10
DBALL/
DBALL2
RF
Prog. Button
LED
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
4: White/Violet: (-) Aux1 Input
5: Violet/Black: (-) Aux2 Input
7: Pink/White: (+) Parking Input
9: Pink: (+) Ignition Input
8: Violet: (+) Starter Input
10: Blue/White: (-) GWR (Status) Input
4
TX
(-) Ground
RX
(+)12V
2
P#: XKD2D65
Page 5
Not required in D2D mode.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2] Connection required for Dodge Journey.
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(+) Brake Input
(-) E-Brake Status Input
14 12
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13 (+) 12V
See page 6 for
wiring information
14
Ignition Isolation (veh. side): Yellow: 8
Ignition Isolation (conn. side): Orange/Yellow: 9
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
Connect for Dodge
Journey only.
This is the only connection required for
parking light output for the Dodge Journey, and
the DBALL MUX connection is not required
OR
(+) Ignition: Pink/White or
Pink/Tan, pin 3
HS CAN High: pin 5
HS CAN Low: White/Brown or
White/Lt. Blue, pin 6
[1] (AC) Tach Output: Violet/White: 5
(+) Brake Output: Gray: 6
(-) E-Brake Output: Black/White: 1
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
RAP Off: Yellow/Black: 10
(MUX) Parking Lights: Violet/Green: 8
(MUX) Parking Lights: Violet/Brown: 9
(+) 12V(+) 12V
(-) Hood Switch(-) Hood Switch
(-) Ground(-) Ground
(-) Driver door trigger
Violet wire in
driver kick panel
All adapters are displayed from the wire side (unless specified otherwise).
Parking
Lights

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
Parking Light Vehicle Wiring Reference Chart (Type 1) Page 6
6
5
4
3
2
1
2
7 8 9
345
6 10
1
Light switch,
black 10-pin plug
Light switch,
black 6-pin plug
Vehicle Years Vehicle Wire Location on vehicle Polarity
DBALL Output from
12 Pin connector or Remote Starter
Chrysler
Town & Country 2011+ White/Green Black connector at light switch, pin 3 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Town & Country 2008-10 White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Dodge/Ram
1500 2011+ White Black connector at light switch, pin 1 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
2500 2011+ White Black connector at light switch, pin 1 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
3500 2011+ White Black connector at light switch, pin 1 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
C/V 2012-15 White/Lt. Green Black connector at light switch, pin 3 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Caravan 2008-10 White/Green Black connector at light switch, pin 3 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Challenger 2008+ White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Challenger
(Smart Key) 2008+ White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Durango 2011+ White/Green Black connector at light switch, pin 3 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Grand Caravan 2011+ White/Green Black connector at light switch, pin 3 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Grand Caravan 2008-10 White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Journey 2009-10 White/Violet Passenger kick panel (+) Remote Starter (+) Parking Lights
RAM 2009-10 White Black connector at light switch, pin 1 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Jeep
Grand Cherokee 2011+ White/Green Black connector at light switch, pin 1 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Grand Cherokee
(Smart Key) 2011+ White/Green Black connector at light switch, pin 1 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Volkswagen
Routan 2011+ White/Green Black connector at light switch, pin 3 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Routan 2009-10 White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
Pink
Installation Type 2a (with CHTHD1 T-Harness R7) Page 7
Remote
Starter
(+) Ignition Input/Output
10
DBALL/
DBALL2
RF
Prog. Button
LED
4
TX
(-) Ground
RX
(+)12V
14 12 2
P#: XKD2D65
Parking
Lights
Connect for Jeep
Commander &
Grand Cherokee only.
See page 10 for
wiring information
White/Orange
White/Gray, White
or White/Pink
Twisted pair in the steering column
or behind radio
FT CAN High: White/Orange: 5
FT CAN Low: White: 6
OR
CHTHD1 R7
(optional)
12-pin Connector
(Vehicle side)
Ignition
Barrel
(vehicle side)
12-pin Connector
(harness side)
12-pin Connector
(harness side)
Do NOT
connect
[2] (-) Parking Light Output
[1] (AC) Tach Input
RAP Off: Yellow/Black: 10
(MUX) Parking Lights: Violet/Green: 8
(MUX) Parking Lights: Violet/Brown: 9
[1] (AC) Tach Output: Violet/White: 5
Remote Start Safety
Override Switch is inactive
(used for RSR only)
[2] Connection only required for Jeep Commander & Jeep Grand Cherokee
Wires not listed in this diagram are not required for the installation.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
(+) 12V(+) 12V
(-) Hood Switch(-) Hood Switch
(-) Ground(-) Ground
(-) Driver door trigger
Violet wire in
driver kick panel or driver
door (Jeeps ONLY).
All adapters are displayed from the wire side (unless specified otherwise).
D2D
only

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
Installation Type 2b (with CHTHD1 T-Harness R1-R6) Page 8
Remote
Starter
(+) Ignition Input/Output
10
DBALL/
DBALL2
RF
Prog. Button
LED
4
TX
(-) Ground
RX
(+)12V
14 12 2
P#: XKD2D65
Parking
Lights
Connect for Jeep
Commander &
Grand Cherokee only.
See page 10 for
wiring information
White/Orange
White/Gray, White
or White/Pink
Twisted pair in the steering column
or behind radio
FT CAN High: White/Orange: 5
FT CAN Low: White: 6
OR
CHTHD1 R1-R6
(optional) Connect to White/Red wire, Pin 3
12-pin Connector
(Vehicle side)
Ignition
Barrel
(vehicle side)
12-pin Connector
(harness side)
12-pin Connector
(harness side)
Do NOT
connect
[2] (-) Parking Light Output
[1] (AC) Tach Input
RAP Off: Yellow/Black: 10
(MUX) Parking Lights: Violet/Green: 8
(MUX) Parking Lights: Violet/Brown: 9
[1] (AC) Tach Output: Violet/White: 5
Remote Start Safety
Override Switch is inactive
(used for RSR only)
[2] Connection only required for Jeep Commander & Jeep Grand Cherokee
Wires not listed in this diagram are not required for the installation.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
(+) 12V(+) 12V
(-) Hood Switch(-) Hood Switch
(-) Ground(-) Ground
(-) Driver door trigger
Violet wire in
driver kick panel
or driver door (Jeeps Only).
All adapters are displayed from the wire side (unless specified otherwise).
D2D
only

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
Installation Type 2c (without T-Harness)
Remote
Starter
1
6
12 7
Connector side view
at ignition switch
(-) GWR (Status)
(+) Ignition Input/Output
(-) Lock Output
(+) Starter Output
(-) Unlock Output
(-) Trunk Output
10
DBALL/
DBALL2
Prog. Button
LED
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
9: Pink: (+) Ignition Input
8: Violet: (+) Starter Input
10: Blue/White: (-) GWR (Status) Input
4
14 12 2
HS CAN High: Tan/Black: 3
FT CAN High: Orange/Green: 5
HS CAN Low: Tan: 4
FT CAN Low: Orange/Brown: 6
P#: XKD2D65
Twisted pair in the steering column
or behind radio White/Orange
White/Gray, White
or White/Pink
Page 9
TX
(-) Ground
RX
(+)12V
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13 (+) 12V
RF
[1] (AC) Tach Output: Violet/White: 5
(+) Brake Output: Gray: 6
(-) E-Brake Output: Black/White: 1
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
RAP Off: Yellow/Black: 10
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(+) Brake Input
(-) E-Brake Status Input
7: Pink/White: (+) Parking Lights Input
(+) Parking Lights Output
(MUX) Parking Lights: Violet/Green: 8
(MUX) Parking Lights: Violet/Brown: 9
Ignition
Barrel
Not required in D2D mode.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Ignition Isolation (veh. side): Yellow: 8
Ignition Isolation (conn. side): Orange/Yellow: 9
Parking
Lights
See page 10 for
wiring information
[2] Connection only required for Jeep Commander & Jeep Grand Cherokee
OR
Parking lights output for
Jeep Commander &
Grand Cherokee only.
[2] (-) Parking Light Output
(+) Ignition: Pink/White, pin 3
HS CAN High: White/Black
or White/Lt. Green, pin 5
HS CAN Low: White/Lt. Blue, pin 6
(+) 12V(+) 12V
(-) Hood Switch(-) Hood Switch
(-) Ground(-) Ground
(-) Driver door trigger
Violet wire in
driver kick panel
or driver door
(Jeeps ONLY).
All adapters are displayed from the wire side (unless specified otherwise).

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
Page 10
Parking Light Vehicle Wiring Reference Chart (Type 2)
Jeep Commander & Jeep Grand
Cherokee
ALTERNATIVE parking light
connection
Light switch,
black 10-pin plug
7
2
6
1
10
5
9
4
8
3
Vehicle Years Vehicle Wire Location on vehicle Polarity
DBALL Output from
12 Pin connector
Chrysler
300/300c 2008-10 White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: (MUX ) Parking Lights
9: Violet/Brown: (MUX ) Parking Lights
Dodge
Charger 2008-10 White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: (MUX ) Parking Lights
9: Violet/Brown: (MUX ) Parking Lights
Magnum 2008 White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: (MUX ) Parking Lights
9: Violet/Brown: (MUX ) Parking Lights
Jeep
Commander 2008-10 White/Dk. Blue Hazard light switch (-) (-) Parking Lights Output
Grand Cherokee 2008-10 White/Dk. Blue Hazard light switch (-) (-) Parking Lights Output
Refer to DirectWire for additional parking light locations.

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
(+) Parking Lights
Remote
Starter
(+) Ignition Input/Output
10
DBALL/
DBALL2
Prog. Button
LED
4
14 12 2
P#: XKD2D65
Installation Type 3a (with CHTHD2 T-Harness R9-R10) Page 11
TX
(-) Ground
RX
(+)12V
RAP Off: Yellow/Black: 10
Pink
N.C.
RF
See page 14 for
wiring information
8-pin Connector
at Sentry Key Module Near
Ignition Switch (vehicle side)
8-pin Connector
(harness side)
8-pin Connector
(harness side)
Sentry Key Module
Near Ignition Switch
(vehicle side)
CHTHD2 R9-R10
(optional)
T-04
Do NOT
connect
Remote Start Safety
Override Switch is inactive
(used for RSR only)
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[1] (AC) Tach Input
[1] (AC) Tach Output: Violet/White: 5
Wires not listed in this diagram are not required for the installation.
(+) 12V(+) 12V
(-) Hood Switch(-) Hood Switch
(-) Ground(-) Ground
All adapters are displayed from the wire side (unless specified otherwise).
D2D
only
(-) Driver door trigger
Violet or Violet/Dk. Blue wire
in driver kick panel or
at driver door module

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
(+) Parking Lights
Remote
Starter
(+) Ignition Input/Output
10
DBALL
Prog. Button
LED
4
14 12 2
P#: XKD2D65
Installation Type 3b (with CHTHD2 T-Harness R1-R6) Page 12
TX
(-) Ground
RX
(+)12V
RAP Off: Yellow/Black: 10
RF
See page 14 for
wiring information
Connect to Red/White wire, pin 3 (male plug) Wire side view
(T-Harness 8-pin Conn.)
1
3
8
8-pin Connector
at Sentry Key Module Near
Ignition Switch (vehicle side)
Sentry Key Module
Near Ignition Switch
(vehicle side)
CHTHD2 R1-R6
(optional)
8-pin Connector
(harness side)
8-pin Connector
(harness side)
[1] (AC) Tach Input
[1] (AC) Tach Output: Violet/White: 5
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Wires not listed in this diagram are not required for the installation.
(+) 12V(+) 12V
(-) Hood Switch(-) Hood Switch
(-) Ground(-) Ground
All adapters are displayed from the wire side (unless specified otherwise).
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
9: Pink: (+) Ignition Input
8: Violet: (+) Starter Input
10: Blue/White: (-) GWR (Status) Input
(-) GWR (Status)
(+) Ignition Input/Output
(-) Lock Output
(+) Starter Output
(-) Unlock Output
(-) Trunk Output
D2D
only
(-) Driver door trigger
Violet or Violet/Dk. Blue wire
in driver kick panel or
at driver door module

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
(+) Parking Lights
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
Remote
Starter
(-) GWR (Status)
(+) Ignition Input/Output
(-) Lock Output
(+) Starter Output
(-) Unlock Output
(-) Trunk Output
(+) Brake Input
10
DBALL/
DBALL2
Prog. Button
LED
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
9: Pink: (+) Ignition Input
8: Violet: (+) Starter Input
10: Blue/White: (-) GWR (Status) Input
4
14 12 2
P#: XKD2D65
Installation Type 3c (without T-Harness)
FT CAN Low: Pin 7
FT CAN High: Pin 6
1 8
Sentry Key Module Near Ignition Switch
(connector side view)
(+) Ignition: Pink or Pink/Striped, pin 3
MUX: Violet/Brown, pin 1
Page 13
TX
(-) Ground
RX
(+)12V
(-) E-Brake Status Input
FT CAN High: Tan/Black: 3
FT CAN Low: Tan: 4
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13 (+) 12V
(+) Brake Output: Gray: 6
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
Multiplex Output: Violet/Green: 8
Multiplex Output: Violet/Brown: 9
(-) E-Brake Output: Black/White: 1
RAP Off: Yellow/Black: 10
[1] (AC) Tach Output: Violet/White: 5
RF
Not required in D2D mode.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
See page 14 for
wiring information
(+) 12V(+) 12V
(-) Hood Switch(-) Hood Switch
(-) Ground(-) Ground
(-) Driver door trigger
Violet or Violet/Dk. Blue wire
in driver kick panel or
at driver door module
All adapters are displayed from the wire side (unless specified otherwise).

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
Vehicle Years Wire Polarity Location
Chrysler
200 2011-14 White/Violet (+) Driver kick panel
Aspen 2007-09 Pink/Red (+) Driver kick fuse box, black 40-pin plug, pin 6
Sebring 2007-10 White/Violet (+) Driver kick panel
Sebring Convertible 2008-10 White/Violet (+) Driver kick panel
Sebring Sedan 2007-10 White/Violet (+) Driver kick panel
Dodge
Avenger 2008+ White/Violet (+) Driver kick panel
Caliber 2007-12 White/Violet (+) Driver kick panel
Dakota 2007-11 Pink/Red (+) Underhood fuse box, black 20-pin plug, pin 15
Durango 2007-09 Pink/Red (+) Driver kick fuse box, black 40-pin plug, pin 6
Nitro 2007-11 White/Violet (+) Driver kick panel
RAM 2006-08 White/Gray (+) Above driver kick, gray 74-pin plug, pin 19
Jeep
Compass 2007+ White/Violet (+) Driver kick panel
Liberty 2008-12 White/Violet (+) Driver kick panel
Patriot 2007+ White/Violet (+) Driver kick panel
Wrangler 2007+ White/Violet (+) Passenger kick panel
Wrangler Limited 2007+ White/Violet (+) Passenger kick panel
Mitsubishi
Raider 2007-09 Pink/Red (+) Underhood fuse box, black 20-pin plug, pin 15
Parking Light Vehicle Wiring Reference Chart (Type 3)
Page 14
46
55
65
20
10
3
29
58
59
61
72
64
17
16
15
14
11
60
17 38 44
31 37 68 74
Above driver kick,
gray 74-pin plug
Underhood fuse box,
black 20-pin plug
10
20
9
19
8
18
7
17
6
16
5
15
4
14
3
13
2
12
1
11
39 25
28
29
32
33 21
36 24
9
12
13
16
820
5
17
1
38 4
37 3
40 2
Driver kick fuse box,
black 40-pin plug

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
Remote
Starter
(-) GWR (Status)
(+) Ignition Input/Output
(+) Starter Output
(-) Lock Output
(-) Aux 2 Heated Seat Activation
(-) Unlock Output
(-) Trunk Output
(+) Brake Input
10
DBALL/
DBALL2
Prog. Button
LED
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
5: Violet/Black: (-) Aux2 Input
9: Pink: (+) Ignition Input
8: Violet: (+) Starter Input
10: Blue/White: (-) GWR (Status) Input
4
14 12 2
P#: XKD2D65
FT CAN Low: White
or White/Pink, pin 7
FT CAN High:
White/Orange, pin 6
11 8
5 or 6
Sentry Key Module
Near Ignition Switch
(connector side view)
(+) Ignition: Pink/White or Pink/Lt. Green, pin 3
(+) Start: pin 4
MUX: Violet/Brown, pin 2
Ignition Switch
(connector side view)
Installation Type 4 Page 15
TX
(-) Ground
RX
(+)12V
RF
(-) E-Brake Status Input
(+) Brake Output: Gray: 6
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
Multiplex Output: Violet/Green: 8
Multiplex Output: Violet/Brown: 9
(-) E-Brake Output: Black/White: 1
[1] (AC) Tach Output: Violet/White: 5
Not required in D2D mode.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Parking Lights
See page 16 for
wiring & polarity information
FT CAN High: Tan/Black: 3
FT CAN Low: Tan: 4
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13 (+) 12V
(+) 12V(+) 12V
(-) Hood Switch(-) Hood Switch
(-) Ground(-) Ground
All adapters are displayed from the wire side (unless specified otherwise).

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
Parking Light Vehicle Wiring Reference Chart (Type 4) Page 16
46
55
65
20
10
3
29
58
59
61
72
64
17
16
15
14
11
60
17 38 44
31 37 68 74
Above driver kick,
gray 74-pin plug
Vehicle Years Wire Polarity Location
Chrysler
300/300c 2005-07 White/Violet (+) Passenger kick panel
PT Cruiser 2006-10 White/Violet (+) Driver kick panel
Dodge
Caliber 2007 White/Violet (+) Driver kick panel
Charger 2006-07 White/Violet (+) Passenger kick panel
Magnum 2005-07 White/Violet (+) Passenger kick panel
RAM 2006 White/Gray (+) Above driver kick, gray 74-pin plug, pin 19
Jeep
Commander 2006-07 White/Dk. Blue (-) Hazard light switch
Grand Cherokee 2005-07 White/Dk. Blue (-) Hazard light switch

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
(-) Hood Switch(-) Hood Switch
(+) Parking Lights
Remote
Starter
(-) GWR (Status)
(-) Lock Output
(-) Unlock Output
(-) Keysense: Violet/Tan, pin 5
10
DBALL/
DBALL2
RF
Prog. Button
LED
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
10: Blue/White: (-) GWR (Status) Input
4
14 12 2
P#: XKD2D65
Diode
FT CAN Low:
White, pin 7
FT CAN High:
White/Orange, pin 6
1 8
Sentry Key Module
Near Ignition Switch
(connector side view)
(+) Starter
(-) Accessory 2
(+) Ignition 1
(+) Ignition 2
*Pin 1 or 8 depending on
the vehicle (see page 18). (+) Accessory 1
Installation Type 5
Connect Keysense wire
only if vehicle is equipped
with OEM alarm.
See page 18 for the ignition
switch wiring information
Page 17
TX
(-) Ground
RX
(+)12V
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(+) Brake Input
(-) E-Brake Status Input
Not required in D2D mode.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
(+) 12V
(-) Ground (-) Ground
92
8
1
147
136
12
114
103
See page 18 for
wiring information
Ignition Switch
(black connector)
(+) Brake Output: Gray: 6
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
(-) E-Brake Output: Black/White: 1
[1] (AC) Tach Output: Violet/White: 5
FT CAN High: Tan/Black: 3
FT CAN Low: Tan: 4
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13 (+) 12V
All adapters are displayed from the wire side (unless specified otherwise).
5
30
86 85
87
87a
(+) 12V or (-) Ground (see page 18)
(+) 12V

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
Vehicle Wiring Reference Chart (Type 5) Page 18
12 V Starter Ignition Ignition 2 Accessory Accessory 2*
Wire Polarity Location
Dodge
Dakota 2005 Pink/Red (+) Underhood fuse box, black
20-pin plug, pin 15 Red, pin 7 Pink/Lt. Blue, pin 13
Pink/Lt. Green,
pin 3 Pink, pin 2 Pink/White, pin 14
Dk. Blue (+),
pin 8
Dakota 2006 Pink/Red (+) Underhood fuse box, black
20-pin plug, pin 15 Red, pin 7 Pink/Lt. Blue, pin 13
Pink/Lt. Green,
pin 3 Pink, pin 2 Pink/White, pin 14
Violet (-),
pin 1
Durango 2004 Pink/Red (+) Driver kick fuse box, black
40-pin plug, pin 6
Red/Dk. Blue,
pin 7
Pink/Lt. Blue,
pin 13
Pink/Lt. Green,
pin 3 Pink, pin 2 Pink/Yellow, pin 14
Dk. Blue (+),
pin 8
Durango 2005-06 Pink/Red (+) Driver kick fuse box, black
40-pin plug, pin 6
Red/Dk. Blue,
pin 7
Pink/Lt. Blue,
pin 13
Pink/Lt. Green,
pin 3 Pink, pin 2 Pink/Yellow, pin 14
Violet (-),
pin 1
Mitsubishi
Raider 2006 Pink/Red (+) Underhood fuse box, black
20-pin plug, pin 15 Red, pin 7 Pink/Lt. Blue, pin 13
Pink/Lt. Green,
pin 3 Pink, pin 2 Pink/White, pin 14
Violet (-),
pin 1
Parking Lights
Ignition Switch, black 14-pin plug
Vehicle Years
Underhood fuse box,
black 20-pin plug
Ignition switch,
black 14-pin plug
92
8
1
147
136
125
114
103
Driver kick fuse box,
black 40-pin plug
39 25
28
29
32
33 21
36 24
9
12
13
16
820
5
17
1
38 4
37 3
40 2
10
20
9
19
8
18
7
17
6
16
5
15
4
14
3
13
2
12
1
11
* Vehicle may not have an Accessory 2 wire in pin 1 or 8. If that is the case, this connection is unnecessary.

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
Module Programming Page 19
Go to the next page to complete the module programming.
Refer to the LED Diagnostics section on page 24 for more information and for troubleshooting purposes.
2or
Insert the key into the ignition barrel and turn it
to the ON position.
Key Ignition Push-to-Start (PTS) Ignition
It is important to wait for the LED to start flashing
green. Refer to the LED Diagnostics section on
page 25 for troubleshooting if the LED does not
flash green within 15 seconds.
&
Flashes Green
Flashes Green
Key IN
OFF
START
ON
It is important to wait for the LED to
start flashing green. Refer to the LED
Diagnostics section on page 25 for
troubleshooting if the LED does not
flash green within 15 seconds.
Press the Push-to-Start (PTS) button twice to
turn the ignition ON.
Important: Do NOT press the brake pedal.
2X ENGINE
START
STOP
PUSH
Do NOT
press the
brake pedal
1
Solid
Wait until the LED turns ON solid red.
Vehicles WITH Factory Keyless
(Refer to the next page for programming instructions WITHOUT factory keyless.)
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 or higher. Using version 2.9 or 3.1 will limit
available functions and features.
1. Connect the interface module to your computer using the XKLoader.
2. Open an Internet Explorer browser (version 6 or higher), and go to www.directechs.com. The detail of the platform and firmware
that is currently saved on the interface module will be indicated in the top left corner of the page.
3. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware.
4. In the search result page, select Flash Standard install, and follow the instructions provided on the screen.
5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module.
6. The following message will be displayed when the upload is completed:
“The flashing is successfully completed. You may now unplug the kit.”
You can now proceed with the programming instructions below.
OR
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to
the module, then connect the 4-pin D2D harness.
D2D Installation
W2W Installation
If required for your installation, connect the 10-pin and 12-pin harnesses to the
module, then connect the 14-pin harness to the module.
10-pin
D2D
st
1
12-pin
14-pin
nd
2
rd
3
10-pin
D2D
st
1
th
4
12-pin
14-pin
nd
2
rd
3

Platform: DBALL/DBALL2
Firmware: CHRYSLER
© 2015 Directed. All rights reserved.
Rev.: 20150128
3
4
Turn the key to the OFF
position and remove it
from the ignition barrel.
Press LOCK or UNLOCK on the
factory transmitter. The LED turns ON
solid green OR orange for 3 seconds and
then turns off.
or & & or
Solid Green Solid Orange Off
Key OUT
OFF
START
IGN
or Press the Push-to-Start
(PTS) button once more
to turn the ignition OFF. 1X ENGINE
START
STOP
PUSH
PANIC
Page 20
Vehicles WITHOUT Factory Keyless
(Refer to the previous page for programming instructions WITH factory keyless.)
4Press and release the Programming Button. The LED
turns ON solid green OR orange for 3 seconds and then
turns OFF. &&
3Turn the key to the OFF position and remove it from the ignition barrel.
2
Insert the key into the ignition barrel and turn it to the ON position.
It is important to wait for the LED to start flashing green.*
* Refer to the LED Diagnostics section on page 25 for troubleshooting
if the LED does not flash green within 15 seconds.
Off
Press & Release
&
Flash Green
Key IN
OFF
START
ON
Key OUT
OFF
START
IGN
Solid
Solid
or
You have successfully completed the module programming sequence.
You have successfully completed the module programming sequence.
1
Solid
Wait until the LED turns ON solid red.