DirekTronik ED3331 User manual

10/100Base-TX Industrial Ethernet Extender
1
Quick Start Guide
This quick start guide describes how to install and use the Ethernet
Extender. The Ethernet Extender introduced here provides one channel for
Ethernet over existing coaxial cable.
Product Overview
Use DIN-Rail Mounting Kit
Fit the DIN-Rail mounting kit onto the bottom of the unit and fasten the screws.
The Ethernet Extender can use DIN-Rail mounting kit to fix on the DIN-Rail.

10/100Base-TX Industrial Ethernet Extender
2
Product Features
yComplies with EN61000-6-2 & EN61000-6-3 EMC Generic standard
immunity for Industrial environment.
yOperates transparent to higher layer protocols.
yOne Ethernet port (RJ-45 connector): 10/100Mbps-Full/Half-duplex,
Auto-negotiation, Auto-MDI/MDIX.
yComplies with IEEE802.3 10Base-T and IEEE802.3u 100Base-TX
standards.
yOne Ethernet Extender port (BNC connector): Symmetrical on the VDSL,
high-speed Full-duplex 85Mbps communications link over existing
coaxial cable.
yProvides BNC to F-Type connector.
ySupports one DIP switch to select local or remote site.
yTen reference speeds supports up to 85Mbps @ about 200 meters
(656ft.), down to 1Mbps @ about 2,600 meters (8,530ft.).
yExternal AC to DC power adapter.
y-10℃ to 60℃(14℉to 140℉) operating temperature range.
yHardened aluminum case.
ySupports DIN-Rail or Wall Mounting installation.
yUsed as a stand-alone device or with a chassis.
yHot-swappable when used with a chassis.

10/100Base-TX Industrial Ethernet Extender
3
Ethernet Extender Mode Settings
Ethernet Extender mode settings are made very simple by means of a
switch at the rear panel of the Ethernet Extender. The switch has two
positions for Ethernet Extender mode settings. Refer to the table below for
more details. One device must be set to Loc and the other to Rmt when two
devices are connected.
Loc Rmt
The device operates in local mode The device operates in remote mode
Connecting to Power
This Ethernet Extender is a plug-and-play device. Connect the supplied AC
to DC power adaptor to the receptacle on the rear panel of the Ethernet
Extender, and then attach the plug into a standard AC outlet.
Front Panel & LEDs
The LED indicators give you instant feedback on status of the Ethernet
Extender:
LEDs State Indication
Steady Power on
Pwr stands for POWERPwr
Off Power off
Ethernet
Steady A valid Ethernet connection established
Lnk stands for LINK
Flashing Transmitting or receiving Ethernet data
Act stands for ACTIVITY
Lnk/Act
Off Neither valid Ethernet connection established nor transmitting/receiving Ethernet
data
Steady Ethernet Connection transferring at 100Mbps
100 Off Ethernet Connection transferring at 10Mbps
Ethernet Extender
Green Link Speed: 1~5Mbps, Distance: 2,600 meters (8,530ft.)
1 Amber Link Speed: 6~10Mbps, Distance: 2,400 meters (7,874ft.)
Green Link Speed: 11~16Mbps, Distance: 2,000 meters (6,561ft.)
2 Amber Link Speed: 17~20Mbps, Distance: 1,800 meters (5,905ft.)
Green Link Speed: 21~29Mbps, Distance: 1,600 meters (5,249ft.)
3 Amber Link Speed: 30~43Mbps, Distance: 1,400 meters (4,593ft.)
Green Link Speed: 44~54Mbps, Distance: 1,200 meters (3,937ft.)
4 Amber Link Speed: 55~63Mbps, Distance: 1,000 meters (3,280ft.)
Green Link Speed: 64~74Mbps, Distance: 600 meters (1,968ft.)
5 Amber Link Speed: 75~85Mbps, Distance: 200 meters (656ft.)
Rmt Steady The device operates in remote mode
Loc Steady The device operates in local mode
Err Steady Error occurred
Lnk Steady A valid connection established
Self-diagnostic Test Procedure
yTwo Industrial Ethernet Extenders are connected in pairs by BNC
connectors over coaxial cable.

10/100Base-TX Industrial Ethernet Extender
4
yOne Industrial Ethernet Extender is configured as local unit located at
local site of Ethernet extension by setting mode switch at rear panel of
this Industrial Ethernet Extender to Loc (local mode).
yThe other Industrial Ethernet Extender is configured as remote unit
located at remote site of Ethernet extension by setting mode switch at
rear panel of this Industrial Ethernet Extender to Rmt (remote mode).
yConnect supplied AC to DC power adaptors to receptacle on rear panel
of these two Industrial Ethernet Extenders and then attach plugs into
standard AC outlet sockets to power on these two Industrial Ethernet
Extenders.
yLED 5 on top panel of these two Industrial Ethernet Extenders might
light on in amber or green color if these two Industrial Ethernet
Extenders are connected in pairs by BNC connectors over a short
coaxial cable (less than 200 meters). This means that these two
Industrial Ethernet Extenders could operate in normal condition since
they finally negotiate a best performance for symmetrical transmission.

10/100Base-TX Industrial Ethernet Extender
5
Preface
This manual describes how to install and use the Ethernet Extender. The
Ethernet Extender introduced here provides one channel for Ethernet over
existing voice grade copper wire.
The Ethernet Extender fully complies with IEEE802.3 10Base-T and
IEEE802.3u 100Base-TX standards.
In this manual, you will find:
yProduct overview
yFeatures on the Ethernet Extender
yIllustrative LED functions
yInstallation instructions
ySpecifications

10/100Base-TX Industrial Ethernet Extender
6
Table of Contents
Quick Start Guide............................................................................................................................... 1
PRODUCT OVERVIEW .................................................................................................................... 1
USE DIN-RAIL MOUNTING KIT ....................................................................................................... 1
PRODUCT FEATURES .................................................................................................................... 2
ETHERNET EXTENDER MODE SETTINGS......................................................................................... 3
CONNECTING TO POWER ............................................................................................................... 3
FRONT PANEL &LEDS................................................................................................................. 3
SELF-DIAGNOSTIC TEST PROCEDURE............................................................................................ 3
Preface .............................................................................................................................................. 5
Table of Contents............................................................................................................................... 6
Introduction ........................................................................................................................................ 7
PRODUCT OVERVIEW .................................................................................................................... 7
PRODUCT FEATURES .................................................................................................................... 7
PACKING LIST ............................................................................................................................... 7
One-Channel Ethernet Extender........................................................................................................ 8
PORTS .......................................................................................................................................... 8
ETHERNET EXTENDER MODE SETTINGS......................................................................................... 8
FRONT PANEL &LEDS................................................................................................................. 8
Installation........................................................................................................................................ 10
SELECTING A SITE FOR THE EQUIPMENT...................................................................................... 10
CONNECTING TO POWER ............................................................................................................. 10
USE DIN-RAIL MOUNTING KIT ..................................................................................................... 11
Specifications................................................................................................................................... 12

10/100Base-TX Industrial Ethernet Extender
7
Introduction
The Ethernet Extender provides one channel for Ethernet over existing
coaxial cable. It can be used as a stand-alone device.
Product Overview
Product Features
yComplies with EN61000-6-2 & EN61000-6-3 EMC Generic standard
immunity for Industrial environment.
yOperates transparent to higher layer protocols.
yOne Ethernet port (RJ-45 connector): 10/100Mbps-Full/Half-duplex,
Auto-negotiation, Auto-MDI/MDIX.
yComplies with IEEE802.3 10Base-T and IEEE802.3u 100Base-TX
standards.
yOne Ethernet Extender port (BNC connector): Symmetrical on the VDSL,
high-speed Full-duplex 85Mbps communications link over existing
coaxial cable.
yProvides BNC to F-Type connector.
ySupports one DIP switch to select local or remote site.
yTen reference speeds supports up to 85Mbps @ about 200 meters
(656ft.), down to 1Mbps @ about 2,600 meters (8,530ft.).
yExternal AC to DC power adapter.
y-10℃ to 60℃(14℉to 140℉) operating temperature range.
yHardened aluminum case.
ySupports DIN-Rail or Wall Mounting installation.
yUsed as a stand-alone device or with a chassis.
yHot-swappable when used with a chassis.
Packing List
When you unpack this product package, you will find the items listed below.
Please inspect the contents, and report any apparent damage or missing
items immediately to our authorized reseller.
yThe Ethernet Extender
yUser’s Manual
yAC to DC Power Adaptor
yBNC to F-Type connector

10/100Base-TX Industrial Ethernet Extender
8
One-Channel Ethernet Extender
Ports
The Ethernet Extender provides one TX port and one Ethernet Extender
port.
For the TX port, it uses RJ-45 connector and auto senses the speed of
10/100Mbps.
For the Ethernet Extender port, it uses BNC connector and auto senses the
speed of 1/5/10/20/30/40/50/60/70/75Mbps.
Ethernet Extender Mode Settings
Ethernet Extender mode settings are made very simple by means of a 2
position switch at the rear panel of the Ethernet Extender.
Mode switch
There is one position on the Mode switch for Ethernet Extender mode
settings. Refer to the table below for more details. One end must be set to
Loc and the other to Rmt when two devices are connected.
Loc Rmt
The device operates in local mode The device operates in remote mode
Front Panel & LEDs
LED Indicators
The LED indicators give you instant feedback on status of the Ethernet
Extender:

10/100Base-TX Industrial Ethernet Extender
9
LEDs State Indication
Steady Power on
Pwr stands for POWERPwr
Off Power off
Ethernet
Steady A valid Ethernet connection established
Lnk stands for LINK
Flashing Transmitting or receiving Ethernet data
Act stands for ACTIVITY
Lnk/Act
Off Neither valid Ethernet connection established nor transmitting/receiving Ethernet
data
Steady Ethernet Connection transferring at 100Mbps
100 Off Ethernet Connection transferring at 10Mbps
Ethernet Extender
Green Link Speed: 1~5Mbps, Distance: 2,600 meters (8,530ft.)
1 Amber Link Speed: 6~10Mbps, Distance: 2,400 meters (7,874ft.)
Green Link Speed: 11~16Mbps, Distance: 2,000 meters (6,561ft.)
2 Amber Link Speed: 17~20Mbps, Distance: 1,800 meters (5,905ft.)
Green Link Speed: 21~29Mbps, Distance: 1,600 meters (5,249ft.)
3 Amber Link Speed: 30~43Mbps, Distance: 1,400 meters (4,593ft.)
Green Link Speed: 44~54Mbps, Distance: 1,200 meters (3,937ft.)
4 Amber Link Speed: 55~63Mbps, Distance: 1,000 meters (3,280ft.)
Green Link Speed: 64~74Mbps, Distance: 600 meters (1,968ft.)
5 Amber Link Speed: 75~85Mbps, Distance: 200 meters (656ft.)
Rmt Steady The device operates in remote mode
Loc Steady The device operates in local mode
Err Steady Error occurred
Lnk Steady A valid connection established

10/100Base-TX Industrial Ethernet Extender
10
Installation
This chapter gives step-by-step installation instructions for the Ethernet
Extender.
Selecting a Site for the Equipment
As with any electric device, you should place the equipment where it will not
be subjected to extreme temperatures, humidity, or electromagnetic
interference. Specifically, the site you select should meet the following
requirements:
yThe ambient temperature should be between -10 to 60 degrees Celsius.
yThe relative humidity should be less than 95 percent, non-condensing.
ySurrounding electrical devices should not exceed the electromagnetic
field (RFC) standards.
yMake sure that the equipment receives adequate ventilation. Do not
block the ventilation holes on each side of the equipment.
yThe power outlet should be within 1.8 meters of the product.
Connecting to Power
yThis Ethernet Extender is a plug-and-play device.
yConnect the supplied AC to DC power adaptor to the receptacle on the
rear panel of the Ethernet Extender, and then attach the plug into a
standard AC outlet.

10/100Base-TX Industrial Ethernet Extender
11
Use DIN-Rail Mounting Kit
Fit the DIN-Rail mounting kit onto the bottom of the unit and fasten the
screws. The Ethernet Extender can use DIN-Rail mounting kit to fix on the
DIN-Rail.

10/100Base-TX Industrial Ethernet Extender
12
Specifications
Applicable Standards IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
Ethernet over VDSL
Fixed Ports 1 x 10/100Mbps Ethernet port with RJ-45 connector
1 x Ethernet Extender port with BNC connector
Speed
10Base-T
100Base-TX
Ethernet Extender
10/20Mbps for half/full-duplex
100/200Mbps for half/full-duplex
1, 5, 10, 20, 30, 40, 50, 60, 70, 75Mbps
Cable
10Base-T
100Base-TX
Ethernet Extender
2-pair UTP/STP Cat. 3, 4, 5
2-pair UTP/STP Cat. 5
Coaxial cable (5C2V, RG6A/U)
Switching Method Store-and-Forward
Forwarding rate 14,880/148,810pps for 10/100Mbps
Per Unit- (8 LEDs): Pwr; Rmt, Loc, 1, 2, 3, 4, 5LED Indicators
Per Port-
RJ-45 (2 LEDs): Lnk/Act; 100
BNC (2 LEDs): Err, Lnk
Dimensions 80.3mm (W) × 109.2mm (D) × 23.8mm (H)
(3.16” (W) x 4.30” (D) x 0.94” (H))
Weight 150g (0.33lb.)
Power External power adaptor 12VDC, 0.5A
Power Consumption 6W Max.
Operating Temperature -10°C ~ 60°C
Storage Temperature -20°C ~ 70°C
Humidity 5 ~ 95%, non-condensing
Safety UL508, EN60950-1, IEC60950-1
EMI FCC Part 15, Class A
EN61000-6-3: EN55022, EN61000-3-2, EN61000-3-3
EMS EN61000-6-2:
EN61000-4-2 (ESD Standard)
EN61000-4-3 (Radiated RFI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)
EN61000-4-11 (Voltage Dips Standards)
Environmental Test
Compliance
IEC60068-2-6 Fc (Vibration Resistance)
IEC60068-2-27 Ea (Shock)
IEC60068-2-32 Ed (Free Fall)