PRO SIGNAL PSG3082 User manual

PSG3082
HDMI OVER Cat6/6a/7 EXTENDER
1

WHAT’s IN THE BOX
OVERVIEW
IMPORTANT SAFETY INFORMATION
INSTALLATION
• HDMI extender using HDBaseT, transmits HD audio and video signal, with infrared
remote control for added convenience.
• Ultra HD video and audio transmission range via Cat6, of up to 70 meters.
• Extends 1080p video transmission up to 70 meters.
Please read these instructions carefully before use and retain for future reference.
Requirements
• An HDMI source device with HDMI OUTPUT interface, DVD, PS3, STB, PC etc.
• A display device with HDMI INPUT port, SDTV, HDTV, projector etc.
• Network cables UTP/STP Cat5e/Cat6/Cat6A/Cat7 network cables, to IEEE-568B.
• When using electrical appliances basic safety precautions should always be followed.
• Check that the voltage indicated on the rating plate corresponds with that of the local
network before connecting the power supply to the mains power supply.
• Do not expose the units to moisture or dust and keep any ventilation slots clear.
• Do not connect or disconnect cables while powered on and in use.
• HDMI 1.3 compatible uncompressed HDMI video signal.
• Apply HDBaseT extend technology.
• Supports ultra HD 4kx2k@60Hz and1080p signal over Cat6 up to 70 meters.
• Support HDCP, CEC, 24 bit deep colour 3D.
• Support uncompressed LPCM audio and compressed DTS-HD, Dolby True HD.
• Support use of source device remote control when viewing from an out of sight
location.
• IR remote function can be used in either direction by switching the IR receiver and
transmitters over depending on required location of the controlling remote control.
• Automatically identies and congures a variety of display modes.
• Features RS232 serial bi-direction passback function.
FEATURES
2
• HDMI Transmitter
• HDMI Receiver
• 12V DC PSU x 2 off
• IR-TX Transmitter
• IR-RX Receiver
• RS232 serial port caps x2 off
• User Manual
Connections
• Connect the signal source equipment to the input port of the transmitter using a
quality HDMI cable.

3
• Plug the IR-TX extender into the IR-IN port of the transmitter. Direct the extender
head towards the remote control sensor on the source device.
• Connect an HDTV to the receiver output port using a quality HDMI cable.
• Plug the IR-RX extender into the IR-IN port of the receiver. Direct the sender head
such that it can receive signals from the remote control for your source device.
• Connect one PSU to the receiver 12V DC socket and connect to the mains supply.
• Connect the second PSU to the transmitter 12V DC socket and connect to the mains
supply.
• Power on the signal source and the display.
1. DC12V: Power input.
2. LED status
1 - Power on indicator.
2 - TX/RX connection established.
3 - Indicates signal is being transmitted.
3. HDBT IN: HDBaseT Network connection.
4. HDMI IN and OUT: HDMI signal connection to source and output devices.
5. IR IN: IR signal input to connect with IR receiver extension cable.
6. IR OUT: IR signal output to connect with IR sender extension cable.
Transmitter Panel Connections
Receiver Panel Connections
MAINTENANCE
• Clean the outside casing with a soft cloth lightly moistened with mild soap and water.
Never use any abrasive or solvents.
• Do not allow moisture to enter the casing.

INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL &
ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical & Electronic
Equipment (WEEE). Any WEEE marked products must not be mixed with general household waste,
but kept separate for the treatment, recovery and recycling of the materials used. Contact your local
authority for details of recycling schemes in your area.
Made in China. PR2 9PP
Man Rev 1.0
SPECIFICATIONS
RS232 SERIAL BI-DIRECTION PASSBACK FUNCTION.
Parameter Description
Video
Standards HDMI 2.0, HDCP 2.2, CEC 24bit deep colour
Resolution supported
480i@60Hz, 480p@60Hz, 576i@50Hz,
576p@50Hz, 720p@60Hz, 1080i @60Hz.
1080p@60Hz,3D, 4KX2K@60Hz
Audio Standards LPCM ,DTS-HD, Dolby True HD
Network Standard Cat6, Cat6a, Cat7, supports PoE
Transmission length 70m: UP to 1080p@60Hz 48bpp,
1080p@60Hz 3D,4Kx2K@60 Hz
IR Support 20~60kHz
wide frequency devices Bi-directional IR transmission
Environment
Working temp 0~55oC @ 0~90% humidity
Storage temp -10~70oC
Power Voltage 12V DC @ 2A
Power consumption TX: 6W RX: 8W
Weight TX:240g RX:250g
Dimensions (W x D x H) 109.5 x 87.0 x 24mm each unit
4
RS232 serial bi-direction passback function.
• Supports baud rates of 4800, 9600, 19200, 28800, 38400, 57600 and 115200 and all
devices must be set to the same rate.
• Check the serial cable connections are as shown here:
• To check or set the baud rate use a serial port test tool
set to 115200 and connected to the port before powering the
units on. The test tool will report the current baud rate set.
• To adjust the baud rate to one of the above settings use the test tool ‘set’ command.