Disc Makers ElitePro User manual

Hardware and Installation Setup Guide
ElitePro with AutoGraph VI Printer
CDR/DVDR Publisher

Service and Contact Information
Free lifetime technical support.
Disc Maker's Technical Support Department is here to help you every step of the way with your
duplication system. Our goal is to minimize your downtime and maximize the return on your
investment. We offer FREE technical support to you for as long as you own your duplicator. If
you run into any problems or have any questions, call us at 1-888-800-4041
Our tech support hours are 9am to 5pm EST Monday through Friday.
Toll Free Service Number 1-888-800-4041
Service Email techsupp[email protected]
Support & Download Website www.dmelite.com
For Supplies and Accessories, visit www.discmakers.com
Please register your ElitePro unit by visiting
http://www.dmelite.com/register
This will allow you to be notified of future software upgrades.
Whenever you contact Disc Makers please have the serial number listed below or on the rear
of your unit, so a customer service representative can log onto your account
You are our customer and we will meet your needs and exceed your expectations!
Disc Makers
Plant and Main Office
7905 N. Route 130
Pennsauken, NJ 08110-1402
Toll Free 800-468-9353
Local 856-663-9030
Fax [phone]
Customer Information Below:
Serial Number and
Software Registration Key Label

ElitePro Setup Guide
3
FOREWORD
It is illegal to duplicate copyrighted discs for any reason other than personal use, unless you
happen to be the copyright owner. The autoloader recording unit is intended for use only by
those identities that are the owners of the copyright or are properly licensed to use the
copyright.


Copyright, Trademark and Service Mark Acknowledgement
Manual Revision 082004 Rev 2
Discmakers and the Discmakers logo © Discmakers
ElitePro is a trademark of Discmakers
Microsoft, Windows, XP and .NET are registered Trademarks of Microsoft Corp.
Intel and Celeron are registered Trademarks of Intel Corporation
Plextor is a registered trademark of Plextor Corporation
Pioneer is a registered trademark of Pioneer Electronics
Sanyo is a registered trademark of Sanyo Corporation
Padus and Discjuggler are registered trademarks of Padus Inc
Primera is a registered trademark of Primera Technology, Inc
Signature IV is a trade name of Primera Technology, Inc
Discus is a trademark of Magic Mouse Productions, Inc
FlexWriter is a trademark of Amtren Corporation
All other trademarks and registered trademarks are the property of their respective owners.
This manual and its contents © 2001 2002 2003 2004 Amtren Corporation
The ElitePro is manufactured under license of Patent 6,141,298 and other Patents Pending

ElitePro Setup Guide
4
Table of Contents
Welcome and Introduction 5
Hardware Overview 6
Unpacking the Hardware (Step 1) 7
Installation of CD Pick Arm (Step 2) 8
Installation and Connection of AC Power Monitor, 9
Keyboard and Mouse (Step 3)
Installation of CD Printer (Step 4) 10
Installation of Ink Cartridges (Step 5) 11
Network Connection (Step 6) 12
Turn the System ON and Boot UP (Step 7) 13
Description of Included Software 14
Selecting Recorders & Printing Port 15
with Drive Assigner (Step 8)
Load Blank Media and Start Duplication (Step 9) 16-18
Design Print Image for Media (Step 10) 19-23
Set Print Image for DiscJuggler (Step 11) 24
Cycle Only Option (Step 12) 25
Start the Job (Step 13) 26
Using Drive Assigner 27
Troubleshooting Guide 28

ElitePro Setup Guide
5
Welcome
Thank you for purchasing your new standalone autoloader CDR/DVDR publisher. This system
has been designed and is manufactured under strict quality guidelines. This product will
provide years of dependable and trouble free operation.
Description
125/200 Piece Input CDR or DVDR Drives 2-Year Warranty on Robotics
Your autoloading duplicator is a multi writer desktop DVD/CD-R copying and printing solution
in a single footprint. As the most versatile duplication system on the market today, it offers
you endless possibilities to automate your DVD/CD-R duplication and printing tasks.
The fast and advanced Center-Pick auto loading mechanism will provide ease of use and
trouble-free operation. The autoloader's components are based on industrial design
technology that will provide years of trouble-free operation.
The autoloader comes standard with an Intel® based internal PC preloaded with Microsoft®
Windows® XP. The unit can be connected to your Ethernet network right out of the box
allowing access to files and premastered images. The DiscJuggler.Net software is available
as an option to allow users on the network to submit CD duplication jobs from their desktop!
The autoloader comes standard with CDR or DVDR/CDR combo writers which are controlled
by Padus’s® award winning DiscJuggler® recording software. The recording software
provides a smooth duplication process with trouble-free operation. The DiscJuggler®
software is firmly embedded within the autoloader's system providing a seamless and reliable
solution to the user
Discus© labeling software is included to enhance your product. The Discus© label making
software is a simple and easy to use program that will enable you to create professional
quality CD/DVD labels.

ElitePro Setup Guide
6
Hardware Configuration
Before starting the installation, please review the following Hardware and Functions.

ElitePro Setup Guide
7
This brief setup guide is provided to get the autoloader operational out of the box. Once you
get the system operational, complete online help can be accessed from the DiscJuggler HELP
Section.
Step 1
Unpacking the Hardware:
Your system was shipped in 3 separate boxes. The larger box contains the autoloader unit,
keyboard, mouse and cables. The remaining two boxes contain the monitor and CD printer.
Carefully open the largest box and remove the top protective cardboard sheet. You will then be
able to remove the following:
CD Pick Arm
Keyboard
Mouse
Printer Control Cable
Printer USB Cable
AC Power Cord
Software and Manual
Set the components on a table that will hold the autoloader unit and your PC. Next, by lifting
straight up, carefully remove the foam container and foam protection over the autoloader unit.
You will see the autoloader in a plastic bag. The autoloader has lifting hand holders on either
side. Use these to remove the autoloader from the box. Remove the autoloader from its bag
and place all shipping components back into the shipping carton for future use. It is important
to always ship the duplicator in its proper container; so, storage of the box and accessories is
necessary. In the event you misplace your packaging and need to ship the duplicator, contact
the service department. A new shipping container will be shipped out.
Next, remove the monitor and the printer from their shipping carton. Place all the components
on the table.
Account for all the components and proceed to installation of the CD Pick Arm.
 
               
                  
                     
               
              

ElitePro Setup Guide
8
Step 2
Installation of CD Pick Arm
The CD pick arm needs to be installed onto the rotate arm. Remove the pick arm from the
bubble wrap packaging. Included with the arm will be a bag containing two black plastic
retainers. These retainers are used to hold the pick arm onto the rotate arm.
Hold the pick arm in one hand. Place the arm onto the slotted resting tray on the upper section
of the column. Plug in the RJ12 (telephone) type connector (NOTE: MAKE SURE THE
CONNECTOR RETAINER HAS SNAPPED INTO PLACE BY PULLING GENTLY ON THE
CABLE). Then secure the arm into place by pressing a retainer into each side of the pick arm.
These steps can be reviewed in the pictures shown below.
The pick arm should freely float or pivot from the point where the retainers were installed
Locate Pick Arm & Retainers
Step 1
Hold Pick Arm in Place & Connect
RJ12 Connector
Step 2
Install / Press in the Black
Plastic Retainers
Step 3
The Pick Arm after Installation
Step 4

ElitePro Setup Guide
9
Step 3
Installation and Connection of AC Power, Monitor, Keyboard and Mouse
Plug the Monitor, Keyboard and Mouse into each of their color-coded connections located on
the rear of the autoloader unit. These connections are identical to the common connections of
standard computers.
Arrange the Monitor, keyboard and mouse to the right side of the autoloader unit, to allow easy
access to the rear of the machine.
Plug the AC power cord into the Monitor and into a standard 115VAC outlet.
Plug the power cord into the power supply of the autoloader, also located on the rear side.
Plug into a standard 115VAC outlet.
It is recommended to plug these components into a common plug strip with AC filtering, as is
common with most high-end computers. Also if the unit is to be located in an area where the
utility or power company experiences frequent outages, utilizing a UPS is strongly
recommended.
Rear View of Connections
Keyboard Connection Mouse Connection
Monitor Connection AC Power Connection

ElitePro Setup Guide
10
Step 4
Installation of the CD Printer
Install the CD Printer and connections per this step.
The autoloader is preset for the CD printer and all operating label software and drivers are included with
the installation CDROM.
Place the printer into the printer holding tray located at the top of the drive stack. Holding the printer with
hands on the left and right side, insert the front on the printer at an angle first, and then let the back
section “drop into” place. The printer should be securely inserted into the print holder tray and should be
completely level.
Plug in the USB printer cable provided with the autoloader into the rear of the printer and into the
USB001 connector on the rear of the autoloader.
Plug in the Printer mini din control cable (this is similar to a keyboard cable and has connectors on both
ends) into matching connectors in the rear of the printer and the rear of the autoloader.
Place the AC Power Adapter that was provided with the CD Printer next to the rear of the printer and
plug into a standard 115V AC outlet. Plug the other end into the power connector on the rear of the
printer. The printer will perform a basic internal test and then wait for additional commands from the
operator or the software.
Press the TOP button to turn the printer on. Use the lower button to open and close the tray.
Install Printer by allowing front section
to rest in place, then lower the
rear section into the tray.
Connect the Printer USB
Cable to the printer
Connect the Printer USB Cable
to USB001 port as shown
Connect the Printer DIN Control
Cable from the Printer to the autoloader

ElitePro Setup Guide
11
Step 5
Installation of Ink Cartridges
When you lift up the front plastic cover of the printer, the ink cartridge holder will slide into the
center of the opening enabling you to replace the ink cartridges.
If the pickarm will not allow the front plastic cover to open, then you may gently push the
pickarm downward by applying downward pressure at the base of the pickarm where it wraps
around the column. NEVER attempt to rotate the pickarm or try to push it downward by
pressing down on the top of it. Doing so will damage the autoloader’s picking mechanism.
Unpack the included ink cartridges. Be sure to remove the tape from the cartridges. Do not
touch the metal contacts or ink nozzles. Release the latches on the cartridge holders. Place
the ink cartridges in their respective color-coded holders. The black cartridge goes in the left
slot of the cartridge holder and the color cartridge in the right slot. To secure the cartridges,
close the top of the cartridge holder. You should hear a “snap” sound as they latch back into
place. Close the printer door.

ElitePro Setup Guide
12
Step 6
Network Connection
You may connect the autoloader to your existing computer network. It may be necessary to
change some of the autoloader’s network settings before it will function properly on your
network.
Connecting the autoloader to your network will allow you to access shared folders and drives
on other computers in the network. The DiscJuggler.Net software allows other users on your
network to submit CD duplication jobs to the autoloader from their desktop. If your network
includes access to the Internet, then you can easily download software updates as they
become available.

ElitePro Setup Guide
13
Step 7
Turn the System ON and Boot UP.
Ensure that all the cables are properly connected. Turn on the autoloader by pressing the
power switch located on the unit’s front right side. A small green LED located on the front of
the unit should light up. If not, check to see that the power supply located at the rear of the unit
is turned on and that it is properly connected to a standard working 115V power outlet. The
system will boot up and you will see several different icons on the desktop
Main Startup Screen
(This is an example; units vary with features, etc)
The environment for the autoloader is Windows XP based, all standard functions of XP are
available. Feel free to look around to see the functions of Windows.

ElitePro Setup Guide
14
The following is a brief description of the functions of each icon.
DiscJuggler Pro Local Batch Mode Duplication from any source.
ImageJuggler Local FAST Duplicate and Print Mode with
asynchronously operation of the drives and the printer. This mode
is best used for medium to high volume production tasks. The
production output will be significantly higher than the batch mode.
To use the ImageJuggler program, you must first create an image
of your CD using DiscJuggler Pro. The ImageJuggler should only
be used by the experienced operators.
Network Console Icon. This allows login and setup of the Network
Server Operating Platform. This package is set to login
automatically upon opening the package. The console ICON will
appear in the lower right desktop area when it is deployed. This
package should be operational at all times to service requests from
the clients on your network. This service of the client work will not
impact the local jobs from either DiscJuggler Pro or ImageJuggler.
This icon runs Discus, the CD labeling program for the CD Printer.
You will have to make a label with this software and then print to a
file. This *.prn file will be utilized in the DiscJuggler software to
print the label of the CD. By default XP places the *.prn file in the
same subdirectory that the Discus CD label is saved to.
This is a standard Windows ICON and can be used to access and
service the embedded computer
This is a default desktop folder that is used to store images
processed by the DiscJuggler software.
The ACC (Autoloader Control Console) provides a graphical
interface allowing you to troubleshoot, update, and adjust your
autoloader unit. This is a useful utility for setup and maintenance of
the autoloader.
This icon runs a terminal program to allow serial connection to the
autoloader’s controller. This function is reserved for technical
service instructions from the Customer Support Staff. Please only
use this mode when instructed to do so by the support staff.

ElitePro Setup Guide
15
Step 8
Using Drive Assigner to select Recording Drives & Printing Port
From the factory, your duplicator is set to use the correct recorder drives and printer port.
However, if you ever reinstall or upgrade the DiscJuggler software, it will be necessary to run
Drive Assigner to select the CD recording drives and printing port to use with the autoloader.
To run Drive Assigner, select Start, All Programs, Padus DiscJuggler, and click on
Drive Assigner. DiscJuggler will review the system and display the devices that it has located.
Select the writers that are located in the autoloader unit by clicking on the boxes beside the
drives. Do not select any CD ROM drives. Also, select the appropriate printing port for
DiscJuggler to use when printing CD labels. The FlexPrinter will use USB001. Click on
Update and then OK when finished with your selection. This process will assign only the
recorders of the autoloader to DiscJuggler and will set which port the software uses to
communicate with your CD printer. The assignment will remain set unless you run the Drive
Assigner again and change your settings.

ElitePro Setup Guide
16
Step 9
Load Blank CD’s and Start Duplication
You are now ready to begin a job or task on the autoloader. Turn on your unit if you have not
already done so. Refer to step seven if necessary. The next steps will take you through a
typical setup and usage of the autoloader. It is recommended to follow these steps and
produce a test job, then move on to the many other functions and features of the autoloader.
Load blank Ink Jet media, data side down, onto the input spindle. The input spindle has three
silver rods located around the outside edge of the media. Please be sure the media does not
stick together and that the media lays flat in the input spindle. You may use the included gray
plastic alignment rod to help ensure that the CDs are properly aligned.
Place a CD-R to be copied on top of the blank media in the input spindle. This will be the
‘master’ for this test run. Use a image of 30 MB or less to allow the test run to be faster.
On the Desktop, click on the DiscJuggler ICON and the DiscJuggler will run.
Click on File, choose New and the panel below will open.
Choose Copy CDs and DVDs from the same burner
(This task will take the CD on the top of the Input Stack; load a temp image to the hard drive
and copy from the temp image.)
Screen of Start of a New Job

ElitePro Setup Guide
17
After you have selected Copy CDs and DVDs from the same burner, the panel below will
open. Choose ACTION from the upper right section. On the PULL DOWN select Write and
Print if you have a CD/DVD printer. Otherwise, select Write.
Under the Source and Destination tab, ensure that the autoloader unit is selected, and NOT
a recorder on your PC. Next enter the number of Copies or disks you want to produce. We
have chosen 25 as shown below:

ElitePro Setup Guide
18
Below Copies is an option called Method. The “slider bar” allows you to select your recording
speed. The maximum possible speed will depend upon the model of recorder in your unit and
the type of media you are using. Since nearly all the CDR and DVDR media on the market
today will burn at 24X and 2X respectively, we suggest those as initial recording speeds. Once
you successfully complete your first job, you can try to burn at higher speeds. Results will vary
depending on which brand and type of media you use.
Burn Speed Selector
Once you have found a burning speed that works well with your media, you can make that
speed the default. To do this, click on the Tools menu located at the top of the DiscJuggler
window. Then click on the Options menu. Next, click on the Defaults tab if it is not already
selected. You will see the following window.
Here, you can change the default write
speed for CDs and DVDs to the speeds
that work best with your media.

ElitePro Setup Guide
19
STEP 10
DESIGN PRINT IMAGE (LABEL) FOR MEDIA
Note: You must be using an Autograph VI CD Printer in the following steps. If
you are using another printer refer to documentation that came with your printer.
Next you have to prepare a print image that can be used by the DiscJuggler software to print
text or graphics on top of the media. To do this you will have to use the Discus labeling
software provide with the autoloader. Locate the Discus CD Labeling Software CDR and note
the CD key on the CD’s paper sleeve. It is in the format of XXX-XXX-XXX. Minimize the
DiscJuggler software and on the Desktop, click on the Discus CD Labeling ICON. The
following screen will appear. Type in your Discus key and click the OK button. This only needs
to be done the first time you use Discus.
Type in your Discus Key.
The Discus software will open.
When the Discus screen below opens, click on CD Label.

ElitePro Setup Guide
20
Choose the Print folder at the top. Verify that Discus is set for the Autograph VI.