Siemens Simatic S7-1500 User manual

CPU 1511-1 PN
(6ES7511-1AK00- 
0AB0)
_
_________________
_
_
_________________
_
_
___
_
______________
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
SIMATIC
S7-1500
CPU 1511-1 PN
(6ES7511-1AK00-0AB0)
Manual
01/2013
A5E31264526-AA
Preface
Documentation guide
1
Product overview
2
Wiring
3
Interrupts, diagnostics, error,
and system messages
4
Technical specifications
5
Dimensional drawing
A

Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E31264526-AA
Ⓟ 01/2013 Technical data subject to change
Copyright © Siemens AG 2013.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

CPU 1511-1 PN (6ES7511-1AK00-0AB0)
Manual, 01/2013, A5E31264526-AA 3
Preface
Purpose of the documentation
This device manual supplements the system manual of the S7-1500 automation system
and the function manuals. All cross-system functions are described in the system manual.
The information provided in this device manual and the system manual enables you to
commission the CPU 1511-1 PN.
Conventions
Please also observe notes marked as follows:
Note
A note contains important information on the product described in the documentation,
on the handling of the product and on the section of the documentation to which particular
attention should be paid.
Note on IT security
Siemens offers IT security mechanisms for its automation and drive product portfolio in order
to support the safe operation of the plant/machine. We recommend that you inform yourself
regularly on the IT security developments regarding your products. You can find information
on this on the Internet (http://support.automation.siemens.com).
You can register for a product-specific newsletter here.
For the safe operation of a plant/machine, however, it is also necessary to integrate the
automation components into an overall IT security concept for the entire plant/machine,
which corresponds to the state-of-the-art IT technology. You can find information on this
on the Internet (http://www.siemens.com/industrialsecurity).
Products used from other manufacturers should also be taken into account here.

Preface
CPU 1511-1 PN (6ES7511-1AK00-0AB0)
4 Manual, 01/2013, A5E31264526-AA

CPU 1511-1 PN (6ES7511-1AK00-0AB0)
Manual, 01/2013, A5E31264526-AA 5
Table of contents
Preface ...................................................................................................................................................... 3
1 Documentation guide................................................................................................................................. 7
2 Product overview ....................................................................................................................................... 9
2.1 Properties.......................................................................................................................................9
2.2 Operating and display elements ..................................................................................................12
2.2.1 Front view of the module with front panel ....................................................................................12
2.2.2 Front view of the module without front panel...............................................................................14
2.2.3 Rear view of the module ..............................................................................................................15
2.3 Mode selector switch ...................................................................................................................15
2.4 Functions......................................................................................................................................16
2.4.1 PROFINET IO ..............................................................................................................................16
2.4.2 PROFIenergy ...............................................................................................................................17
2.4.3 Memory reset ...............................................................................................................................17
2.4.4 Restoring the factory settings of the CPU....................................................................................19
3 Wiring ...................................................................................................................................................... 21
4 Interrupts, diagnostics, error, and system messages............................................................................... 25
4.1 Status and error display of the CPU ............................................................................................25
5 Technical specifications........................................................................................................................... 29
A Dimensional drawing ............................................................................................................................... 39

Table of contents
CPU 1511-1 PN (6ES7511-1AK00-0AB0)
6 Manual, 01/2013, A5E31264526-AA

CPU 1511-1 PN (6ES7511-1AK00-0AB0)
Manual, 01/2013, A5E31264526-AA 7
Documentation guide 1
Introduction
The documentation of the SIMATIC products has a modular structure and covers
a range of topics concerning your automation system.
The complete documentation for the S7-1500 system consists of a system manual,
function manuals and device manuals.
The STEP 7 information system (Online Help) also helps you to configure and program
your automation system.
Overview of the documentation for CPU 1511-1 PN
The following table lists additional documents which supplement this description
of CPU 1511-1 PN and are available on the Internet.
Table 1- 1 Documentation for CPU 1511-1 PN
Topic Documentation Most important contents
System
description
S7-1500 Automation System
(http://support.automation.siemens.com/
WW/view/en/59191792) system manual
•Application planning
•Installation
•Wiring
•Commissioning
Power supplies
(http://support.automation.siemens.com/
WW/view/en/57251228) device manual
Properties of the
modules
Signal modules
(http://support.automation.siemens.com/
WW/view/en/59174020) device manual
•Wiring
•Parameter assignment/
addressing
•Interrupts, diagnostics, error,
and system messages
•Technical specifications
•Dimensional drawing
System
diagnostics
System diagnostics
(http://support.automation.siemens.com/
WW/view/en/59192926) function
manual
•Overview
•Hardware/software diagnostic
evaluation

Documentation guide
CPU 1511-1 PN (6ES7511-1AK00-0AB0)
8 Manual, 01/2013, A5E31264526-AA
Topic Documentation Most important contents
Communication
(http://support.automation.siemens.com/
WW/view/en/59192925) function
manual
•Overview
PROFINET with STEP 7 V12
(http://support.automation.siemens.com/
WW/view/en/49948856) function
manual
•PROFINET basics
•PROFINET functions
•PROFINET diagnostics
Communication
Web server
(http://support.automation.siemens.com/
WW/view/en/59193560) function
manual
•Function
•Operation
Designing
interference-free
controllers
Designing interference-free controllers
(http://support.automation.siemens.com/
WW/view/en/59193566) function
manual
•Basics
•Electromagnetic compatibility
•Lightning protection
•Housing selection
Memory concept Structure and use of the CPU memory
(http://support.automation.siemens.com/
WW/view/en/59193101) function
manual
•Setup
•Function principle
•Use
Cycle and
response times
Cycle and response times
(http://support.automation.siemens.com/
WW/view/en/59193566) function
manual
•Basics
•Calculations
Analog value
processing
Analog value processing
(http://support.automation.siemens.com/
WW/view/en/59193559) function
manual
•Wiring options
•Tables of measured values
SIMATIC manuals
All current manuals for SIMATIC products are available for download free of charge from
the Internet (http://www.siemens.com/automation/service&support).

CPU 1511-1 PN (6ES7511-1AK00-0AB0)
Manual, 01/2013, A5E31264526-AA 9
Product overview 2
2.1 Properties
Order number
6ES7511-1AK00-0AB0
View of the module
The following figure shows a CPU 1511-1 PN.
Figure 2-1 CPU 1511-1 PN

Product overview
2.1 Properties
CPU 1511-1 PN (6ES7511-1AK00-0AB0)
10 Manual, 01/2013, A5E31264526-AA
Properties
The module has the following technical properties:
● Communication:
– Interfaces
The CPU 1511-1 PN has a PROFINET interface with two ports. The two ports have
the same IP address and form the interface to the fieldbus level (switch functionality).
– Integrated Web server
The CPU status query is independent of a software installation. Graphically visualized
process variables and user-defined websites facilitate information acquisition.
● Trace functionality
– All CPUs of the S7-1500 automation system support trace functionality.
Trace functionality is independent of the technology and supports you in
debugging/optimizing the user program. It is particularly useful for Motion Control
and control applications.
● Integrated technology:
– Standard Motion Control
PLC Open blocks for programming motion functionality by means
of PROFINET IO IRT and PROFIdrive interface.
The functionality supports speed-controlled axes, positioning axes
and external encoders.
– Integrated control functionality
Universal PID controllers or 3-point controllers with integrated tuning.
Integrated temperature controller
● Integrated system diagnostics:
– System diagnostics is automatically generated and consistently displayed.
● Integrated security:
– Know-how protection
User programs can be securely protected against unauthorized access and
modification.
– Copy protection
User program blocks are linked to the serial number of the SIMATIC memory card
or of the module. User programs cannot run without the corresponding
SIMATIC memory card or module.
– Access protection
Extended access protection provides comprehensive protection against unauthorized
configuration changes. Authorization levels can be used to assign separate rights to
different user groups.
– Integrity protection
The system protects the data transferred to the CPU from unauthorized manipulation.
Altered or external transmission of engineering data is reliably detected by the CPU.