Discount Car Stereo A2D-VWR Instruction Manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
A2D-VWR
MUSIC STREAMING QUICK START INSTALLATION GUIDE FOR AUDI-VW GROUP RADIOS

PRODUCT SAFETY & DISCLAIMER
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE
PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY
•This document is provided as a GENERAL installation guide, some vehicles vary and may
require additional steps. We do not accept responsibility for third party labor charges or
modifications. Exercise due-diligence when installing this product.
•We do not accept any responsibility for vehicle damage or personal injury resulting from
the installation of this product.
•Careless installation and operation can result in equipment damage.
Requirements
CD changer controlling radio
Introduction
Portable audio products are everywhere, reflecting demand from active people
all over the world to take their music on the road. The A2D-VWR provides a
Wireless streaming audio option for any A2DP enabled Smartphone or Tablet
and allows the user to stream their music apps including turn by turn directions
directly into the Audi Concert, Concert II, Symphony, Symphony II and
Volkswagen Single DIN radios. This streaming audio option replaces the factory
external CD/changer, XM.
See Frequently Asked question at the end of this guide for more details.
Installation
(VW and non-Bose systems)
Remove radio from dashboard to gain access to connectors. A pair (Single DIN)
or 2 pairs (Double DIN) removal tools- available separately (See Fig. 1) required
for radio removal.
Fig. 1
Radio removal Tools
1. Slide tools into slots to detent position. Withdraw the radio by pulling
outwards on the tools. See Fig. 2
Fig. 2
2. If present, disconnect Blue (C-3) Green (C-2) and Yellow (C-3) iso
plugs from radio (See Fig. 3).
Fig. 3
Radio connectors

3. Connect installation harness Blue ISO plug (See Fig. 4) into C-3 slot
vacated in step 2—proceed to step 4 below.
Installation:
AUDI: Audi radios have a solid 20-pin plug across chambers A-C (See Fig. 4)
1. Disconnect solid 20-pin plug from radio
2. Connect solid 20-pin plug to installation harness 20-pin connector
(Red)- See Fig. 5.
Fig. 4
Fig. 5
3. Connect installation harness Blue, Green and Yellow ISO plugs (See Fig.
6) to radio as seen in Fig, 3
Fig. 6
4. Secure black wire to ground or to radio chassis as seen in Fig. 7
Fig. 7
Ground wire to radio chassis
5. Secure module and proceed to next section

Pairing
Pairing process varies among devices but the basic steps are the same. This
process is done upon initial install and will not have to be repeated.
1. Turn Ignition and radio “ON”
Blue LED inside module will flash (pairing mode)
2. On A2DP device: Go to Settings, Wireless & Networks, Bluetooth
Settings
3. Select Bluetooth and turn on.
4. Select Bluetooth settings
5. Tap Scan (Search) for devices .
6. Wait for Bluetooth device name to appear (See below) and select it.
Blue LED will glow steady (paired) and tone is heard on car speakers.
Noteworthy: On Androids, it is possible to change paired device name
(e.g. Sky) to something of your own liking. This option may only be available
on older IOS
Optional
The following three options are not required for operation; however, these do
enhance user experience.
To add either to order, tick option on product page.
Smart remote control:
Instead of fumbling around for smartphone, simply press the familiar remote-
control buttons while also keeping your eyes on the road.
Optional remote control allows users to:
1. Control music wirelessly
2. Track up/down
3. Play/Pause (Android)
4. Volume up/down
Pairing:

Operation:
Use wireless remote to perform the following functions on any iOS7.0 and higher
or Android 4.4 and higher.
Package Contents:
Operation
1. Turn ignition and radio “ON”
2. Press “CD” button on radio to enter “Bluetooth” Mode
3. Launch Smartphone streaming application.
4. Use radio volume control button to set playback level. If distorted,
lower volume on phone or if inaudible, raise volume on phone.
Warning: Playlist and Track selection *NOT* possible from the radio
buttons. Use smartphone built-in controls to access or optional
smart remote.
5. If correct operation is confirmed, tuck away any extra wires and re-
install radio.