Discount Car Stereo A2D-BKRCD User manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
A2D-BKRCD
QUICK START MUSIC STREAMING MODULE INSTALLATION GUIDE FOR BECKER WITH ANALOG CD CHANGERS

PRODUCT SAFETY & DISCLAIMER
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE
PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY
•This installation guide is provided as a GENERAL installation guide, some vehicles vary and
may require additional steps. We do not accept responsibility for third party labor charges
or modifications. Exercise due-diligence when installing this product.
•We do not accept any responsibility for vehicle damage or personal injury resulting from
the installation of this product.
•Careless installation and operation can result in equipment damage.
Requirement
CD changer in trunk OR/hatch
Introduction
Many Becker radios lack AUX menu option which means they are not able to
support an auxiliary connection; however, if vehicle has a CD changer, the A2D-
BKRCD is the ticket to add music streaming without sacrificing the original radio
or changer. With the A2D-BKRCD installed, music streaming from smartphone,
tablet, kindle etc. is possible while also retaining use of required CD changer.
Keep in mind for the A2D-BKRCD module to work, vehicle must have a Becker
radio and CD changer such as the CDC-3 (BE2660), BE7860 etc. which
remains connected and operational.
Digital CD changers such as the CDC-4 and others from later models do
not apply.
See Frequently Asked question at the end of this guide for more details.
Installation
Warning: We recommend disconnecting car battery. But before anything
locate and record the radio safe code. Don’t disconnect battery if radio code
is not available, otherwise radio will cease to operate
1. Remove radio from dash to gain access to the connectors. A set of
radio removal tools (See Fig. 1) required.
Fig. 1
Radio removal Tools
Fig. 2
2. Slide tools into slots (51) on radio. (Straight edge facing away).
Withdraw radio by pulling outwards. To release keys simply press
retaining springs. See Fig. 2. For detailed radio removal click here.

3. With radio removed press release tab on BLUE plug (See Fig. 4) and
disconnect from chamber (C-3) (See Fig. 3)
Fig. 3
Radio chamber
Warning: Chamber C-1 is reserved for vehicles amplifier. YELLOW plug (if
present), remains connected.
4. Connect BLUE plug from installation harness (See Fig. 4) into chamber
C-3 vacated in step 3
Fig. 4
8-pin plug
Fig. 4b
installation harness
5. Connect BLUE plug removed from radio in step 3 to mating BLACK
connector on installation harness (Fig. 4b)
Warning: Becker radios are coded and will not operate without code. Do not
proceed to step 6 if radio code is not available.
6. Disconnect factory 8-pin BLACK plug from radio (See Fig. 5)
Fig. 5
7. Connect factory 8-pin BLACK plug to power harness matting 8-pin
connector (See Fig. 6)
8. Connect power harness 8-pin BLACK plug to radio chamber vacated in
step 6
Fig. 6
power harness
9. Test for engine noise. If present a noise filter (not included) may be
required.

Warning: Unlike other European vehicles, BMW and Mercedes
power/speaker plug is molded together (See Fig. 7) which means the
standard power harness (See Fig. 6) does not apply. For these applications
we are including harness seen in Fig.8. To install, follow steps 6-10 taking
into account chambers Block A (BLACK) and block B (BROWN) are molded
together (solid BLACK)
Fig. 7
Fig. 8
Fig. 9
BMW traffic pro with solid 20-pin ISO plug requires our PXHAD3 adapter
harness (sold separately)
10. Secure adapter box and proceed to next section.
Pairing
Pairing process varies among phones but the basic steps are the same. This
process is done upon initial install and will not have to be repeated
1. Turn Ignition and radio “ON”
Green LED through peephole will flash (pairing mode)
2. On A2DP device: go to Settings, Wireless & Networks, Bluetooth
Settings
3. Select Bluetooth and turn on, select Bluetooth settings
4. Tap Scan for devices .
5. Wait for the Bluetooth device name to appear (See Fig. 10) and select
from list. Once paired Green LED will glow steady.
Fig. 10
Notes: Supports multiple phones but connect to one phone at a time.
It may be possible to change above Bluetooth name on older devices.

Operation
1. Turn ignition and radio “ON”
2. Press CD or button combination to enter CD changer mode
(At least 1 disc must be loaded and remain in changer magazine)
3. Set Smartphone or tablet initial volume level to 75% and launch streaming
application
4. Use radio volume control button to set playback level. If distorted, lower
volume audio device volume accordingly.
Warning: Playlist, Track selection, text display is *NOT* possible from
radio. Use audio device built-in controls and display or purchase
optional remote control
Listen to CD changer:
a. Press radio’s “CD” button or button combination to access CD changer
playback
b. Disable Bluetooth on audio device (e.g., smartphone)
CD playback is enabled. Control changer from radio buttons as customary.
To resume streaming:
Enable Bluetooth on audio device and enable streaming app.
Note: Music streaming has priority for as long as audio device is paired. CD
changer playback is only possible if audio device is not paired or out of
range (approx. 30 ft.)
5. If operation is confirmed, reinstall radio
Optional remote
Optional remote control allows users to:
1. Control music wirelessly
2. Activate Phone commands (Siri, Google play etc.)
3. Track up/down
4. Volume up/down
Pairing: