Discount Car Stereo JAGCD-HF Instruction Manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
JAGCD-HF
QuickStartBluetoothInstallationGuideforselectJaguarxJ&xKwithCDChanger
Works in 1998-03 x308 and 1997-06 x100
Created May 15, 2016
Revised: January 11, 2020

Introduction:
Safety comes first when you’re on the road, so having an intuitive and easy to
use Bluetooth kit is essential to reducing driver distraction. The JAGCD-HF
Bluetooth receiver is compatible with virtually all smartphones, and sounds
great for mobile conversations or streaming music. In addition, the JAGCD-HF
requires and retains factory installed CD changer and also includes a USB
port to changer devices. The included audio adapter connects at the changer in
trunk/boot and module installs beneath center console glove box (armrest).
See Frequent Asked questions and Feature Comparison at the end of this
guide.
Audio module Installation:
1. Remove carpet trim piece surrounding audio rack
2. Remove (4) 8mm nuts securing rack to vehicle.
3. wiring and connections are behind the units
4. Locate CD changer single thick black cable (connects changer to
Amplifier in premium systems or radio in standard systems) (See
Fig. 1)
Noteworthy: There are a few cables with similar size/color in this area.
The single thick black cable from changer chassis is the correct one
Fig. 1
5. Remove cable from holding tab and disconnect them by gasping both
plugs and gently pulling apart (do not twist)
6. Once disconnected; CD changer female connector (right),
amplifier/radio plug (left) see Fig. 2
Fig. 2
7. Mate CD changer connector to audio module right angle male plug.
Note: Module right-angle plug (See Fig. 3) does not have an alignment
arrow indicator, however the imaginary arrow (See Fig. 3) must be
opposite arrow on factory changer connector. Once aligned mate both
(do not twist).
Fig. 3
Fig. 3a

8. Connect factory male (See Fig. 2) audio module female (See Fig. 3a)
9. Route 6-pin plug (See Fig. 4) on audio cable to center console area.
Routing Audio cable (sedan)
1. Use a pry tool to open gap between window pillar and rear deck as
seen in Fig. 5. From inside trunk fish audio plug (See Fig. 4) through
and into the cabin. (See Fig. 6 )
Fig. 4
12 ft. Audio cable
Fig. 5
Fig. 6
2. Pull excess cable and begin tucking under backrest and seat cushion as
you work towards the rear of the center glove box (armrest) as seen
in Fig. 7, Fig. 8 and Fig. 9
Fig. 7
Fig. 8
Fig. 9
3. Continue to use pry tool or fingers to fish wire under center glove box
to storage bin.
4. To remove storage bin: Open the center glove box and remove 2
Philips head screws from latch cover and two more from hinge then
remove the single screw on retainer bracket.
5. Lift to remove storage bin and set aside.
6. Locate audio plug fed through in step 3 and gently pull excess cable.
Note: The aforementioned steps apply to sedan models. X100 (convertibles)
requires additional steps not part of this guide.

Installing Bluetooth Module
In our t 2001 XJR Premium Audio test vehicle, Bluetooth module was
secured to center armrest sidewall (See Fig. 10). In this area you will also
find factory phone plug (See Fig. 11) and cigar lighter, either of which can be
used to power module (see Fig. 10).
Fig. 10
Fig. 11
Bluetooth Module Red wire requires 12V Accessory supply (Do not connect
to constant battery supply) and Black wire must be grounded.
Factory connector/Plug
Accesory wire
Ground wire
10-pin Female (white)
Pin 10 (light green)
Pin 6 (black)
10-pin Male (yellow)
Pin 10 (white/green)
Pin 6 (black)
14-pin (yellow)
Pin 13 (Green)
Pin 11n (black)
18-pin male (yellow)
Pin 5 (Green)
Pin 11 (black)
Fig. 11b
1. If vehicle has no phone plug, use cigar lighter under console:
Tap module’s Red wire to White/Blue= 12V ACC and Black wire to
Black=Ground
Fig. 12
Note: Cigar lighter supplies may introduce noise into the system. This is not the result of a faulty
module but your vehicles electrical system. Find a clean power/ground supply (we recommend
factory phone plug). If engine noise is still an issue, consider adding a noise filter.

2. Connect 6-pin audio splitter plug (See Fig. 13) to audio cable 6-pin
connector (routed from trunk/hatch)
Fig. 13
Audio splitter
3. Connect audio splitter straight 3.5mm plug (See Fig. 13) to Module
input jack labeled (CD) (See Fig. 14)
Fig. 14
Audio Jack in center
4. Connect audio splitter right angle 3.5mm plug (See Fig. 13) to module
pigtail jack (See Fig. 15)
Note: Older version of the audio splitter may have these functions reversed. If
there is no audio playback or if audio is low/distorted it’s likely because these
are reversed and the right-angle plug must be connected to the “CD input
instead of pigtail jack.
Fig. 15
pigtail jack
5. Connect microphone/push-button (See Fig. 16) to Module mic input
jack (See Fig. 14)
Fig. 16
Control button/Microphone
6. Consider where to install control button/mic. The microphone is built-
in and must be facing forward for voice commands and phone dialog
(cable is 6ft. long). We recommend completing the remainder of
the install prior to securing the button. Once settled on location,
remove tape backing (See Fig. 17) and stick to dash (See Fig. 18)
or purchase our G2-HF visor kit which allows microphone to be
mounted separately. See Optional Microphone/control button
installation kit at the end of this guide.

Fig. 17
Control/Mic button
Fig. 18
Control button/mic on dash
Make sure no ventilation duct is pointed towards the mic.
It is best to mount button facing driver
USB CHARGING PORT
The USB port is for charging only. Should you decide to use it, we suggest one of
3 connecting options:
A. Flush to dash/panel (requires drilling a ¾” hole)
B. Flush Mount with Support bracket (use this option to mount USB wherever
your installation demands without drilling)
C. Use your own cable- (default)
A. Flush Mount to Dash or Panel (drilling required)
1. Drill a ¾” hole in dash or panel using a step drill bit or equivalent (See
Fig. 19)
Fig. 19
Step drill bit
2. Insert 3.2ft. (1 Meter) USB male terminal (See Fig. 20) through the ¾”
hole created in step 1 and connect to USB port on Module (See Fig. 21)
Fig. 20
Flush mount USB cable

Fig. 21
Module USB port
3. Push USB header (See Fig. 22) until it snaps in place and flush with
mounting surface (See Fig. 23)
Fig. 22
Flush mount USB Terminal
Fig. 23
Flush mounted to dash
4. Tuck and secure any extra wire from moving parts
Note: Many have reported a flush install to back wall in storage
compartment.
B. Flush mount with Support Bracket (No drilling)
1. Locate a flat surface at location of choice within 3.2 ft. (1 meter) of
module and mount USB support bracket (See Fig. 24) to surface using
adhesive/tape or screws.
Fig. 24
USB mounting bracket
2. Insert USB male terminal through hole in bracket (See Fig. 25) and
connect to USB port on Module (See Fig. 21)
Fig. 25
3. Push USB header until it snaps in place and flush (See Fig. 26)
Fig. 26
4. Tuck and secure any extra wire away from moving
C. No USB Mount (default)
USB port is for charging only. Connect your own USB2.0 extension cable or
proceed to next step if charging is not required.

Bluetooth Pairing and Connection
This process is required on initial install. After initial pairing, the Bluetooth
receiver will automatically connect with paired phone upon entering the vehicle.
1. Turn vehicle ignition to “ON”.
2. Red LED inside module will begin to flash
3. On incoming/outgoing calls, ring tone plays on car speakers
4. Access your Smartphone Bluetooth menu settings, and search (scan)
for devices.
5. Select the G2 and tap “Connect”
Note: Pairs up to 4 phones but connects to one phone at a time.
Warning! Caller ID and text display are not possible on factory Radio. Operate Bluetooth device
by pressing the control button or Voice Recognition application. Use radio volume control button
to control playback level.
Bluetooth Operation
1. Turn ignition to ACC position and radio to ON.
2. Press “CD” button on radio. Track or Disc number are displayed only if
they are disc in Changer magazine otherwise “NO MAGAZINE” is
displayed (See Fig. 27)
Fig. 27
Radio must be in “CD Mode” when using the JAGCD-HF.
CD changer remains connected and operational.
3. Use radio volume button to adjust playback level
Music Commands
The following music command are possible from the control button
To
Proceed this way
Pause song
Press and release button
Resume play
Press and release button
Skip to next song
Press button twice
Skip to previous song
Press button three times
Activate CD changer mode*
Press button four times
Activate Voice control
Press/hold button for 2 seconds
Switch from Aux to music streaming
Press and release button

Phone Commands
From control button the following phone commands are possible.
To
Proceed this way
Answer call
Press and release button
End call
Press and release button
Reject incoming call
Press button twice (call goes to VM)
Cancel outgoing call
Press button twice
Activate Voice Control
Press/hold button for 2 seconds
Notes:
1. If playback is distorted or low, adjust volume on phone.
2. To reset Module press and Hold button for 5 seconds (this will not un-pair phone
or erase stored phones)
3. Bluetooth range is approximately 30 ft. make sure device is within range of receiver
4. Voice command compatible with Apple (Siri), Android (Google Now), Blackberry
(Assistant)
5. *Audio controls not applicable to factory changer. Use changer controls buttons on
radio as customary.
6. Upon ending call, music streaming is resumed, however to resume CD changer
playback control button must be pressed 4 times
If successful reverse the removal steps and secure control button/microphone
to dash as per step #6 in “installing Bluetooth module” instructions.
Congratulations, you’ve just updated your vehicle to support new technology
while preserving the original radio and dash components.
Enjoy!
CD Changer Operation
The JAGCD-HF unlike our JAG-HF and BT45-JAG retains CD changer functionality.
To operate, press “CD” button on radio, then press control button 4 times. To
exit CD changer mode press control button once. (returns to music streaming)
Use radio buttons to control changer as customary.
TIP: If at some point the need should arise to connect an audio device (e.g. satellite
radio, MP3 player et) to the system, you may disconnect 3.5mm plug from module “CD”
jack and connect audio device in its place. CD changer will no longer play.
Feature Comparison:
Feature
JAG-HF
JAGCD-HF
BT45-JAG
CD changer retention
X
✓
X
Audio input (aux)
✓
✓*
X
Charging (USB)
✓
✓
X
Built-in mute feature
X
X
✓
Separate microphone
X**
X**
✓
Requires CD changer
✓
✓
✓
Voice Activation
✓
✓
✓
Requires factory phone plug
X
X
✓
Plug-n-play installation
X
X
✓
*Aux input instead of CD changer
** with optional G2-HF kit

Optional visor microphone Kit
The default button has a built-in microphone (See Fig. 28)
Fig. 28
which means mounting the button in certain areas may be great for controls, but
may not so great for issuing voice commands or holding Bluetooth
conversations. The optional G2-HF kit allows for a more conventional microphone
install to visor etc. (See Fig. 29)
Package contents:
Microphone with visor clip on 10ft. cable x 1
Control button (green) x 1
Slitter harness x 1
Fig. 29
Fig. 30
Installation:
1. Use clip to secure microphone to visor or location of choice and route
cable behind the dash.
2. Connect microphone right angle 2-pin plug to “Mic input” jack on
splitter harness (note lip on mic input jack in Fig 31)
Fig. 31

3. Connect splitter 4-pin plug (to module “Mic” input) to blue input jack on
module seen in Fig. 32
Fig. 32
4. Connect 4-pin plug from control button to 4-pin jack on splitter
(labelled control button in Fig.31)
Warning: If you experience clicking sound or no audio, please refer back to
the installation steps above. The likely cause is the microphone and control
buttons connections are reversed.
You may also use the blue push button with the visor kit.
Frequent asked questions
1. I’m having trouble pairing second phone. What is the process?
In order to pair a second phone you must disconnect paired phone. Once module is
free, it will be ready for pairing.
2. Where do I connect the audio adapter?
The audio adapter included in kit must be connected to the CD changer short
pigtail connector in trunk or hatch. The CD changer pigtail cable is located behind
audio rack.
3. In which model/year Jaguars will the JAGCD-HF work and where does the
audio adapter connect?
1998-99 x308 (To Changer/Trunk)
1997-99 x100 (To Changer/Trunk)
4. Will the stereo mute when I receive or make a phone call?
This system will not mute unless radio is in “CD” mode (Bluetooth mode). If in radio
(AM/FM) Mode and a call comes in, the audio system will not mute and in order to
hear caller; radio must be switched “CD” (Bluetooth Mode)
5. Will I be able to use both music and Navigation apps at the same time?
YES! When streaming audio and Navigation apps; music will mute during navigation

guidance and return to previous state when guidance ends. If a call is made or
received, both Navigation guidance and audio streaming are muted until the call
has ended.
6. After installing and testing the system everything works, but there is engine
“whine”. (increases with RPM) What can I do to fix this?
7. Check ground wire and make sure all connections are snug.
If powering module with cigar lighter: remove device plugged into cigar port.
Relocate ground wire,
Install a suitable noise filter.
8. Which devices can be charged on the USB charging port?
The USB charging is compatible with most devices requiring 2A charging current.
Notes:
- Muting is not possible in AM/FM mode. Muting is only possible in “CD”
(Bluetooth) mode.
- Must use mic/push button included with kit or optional G2-HF visor mic kit.
factory mic (if present) does not apply.
- CD changer required and remains functional.
Disclaimer
• This product has no affiliation with Jaguar or Apple
• We’re not liable for misuse of this product.
Email [e-mail]
© 1995-Jan-20 Discount Car Stereo, Inc. All rights reserved. Information in this document is
subject to change without notice. Other products and companies referred to herein are
trademarks or registered trademarks of their respective companies or mark holders.