Discount Car Stereo JAG-HF User manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
JAG-HF
QUICK START BLUETOTH INSTALLATION GUIDE FOR SELECT JAGUAR XJ & XK WITH CD CHANGER
1998-03 x308 and 1998-06 x100
Created May 15, 2016
Revised: March 13, 2021

PRODUCT SAFETY & DISCLAIMER
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE
PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY
•This installation guide is provided as a GENERAL installation guide, some vehicles vary and
may require additional steps. We do not accept responsibility for third party labor charges
or modifications. Exercise due-diligence when installing this product.
•We do not accept any responsibility for vehicle damage or personal injury resulting from
the installation of this product.
Careless installation and operation can result in equipment damage
Introduction:
Safety comes first when you’re on the road, so having an intuitive and easy to
use Bluetooth kit is essential to reducing driver distraction. The JAG-HF kit is
compatible with virtually all Bluetooth phones, and sounds great whether you are
using it for mobile conversations or streaming music. In addition to Bluetooth,
the JAG-HF provides a 3.5mm Audio input which can be used to connect
and play audio devices such as MP3 Players, iPods, Zune, iPads etc. (this
audio input replaces CD changer playback). The built-in USB charging port
can be used to charge devices (2A), however for larger current hungry devices
(e.g., iPhone 8 and newer), we recommend adding optional USB-DMA3 “Fast
Charge” kit. The AUX audio adapter connects at changer in trunk or hatch and
Bluetooth module installs beneath center console glove box (armrest).
CD changer required, remains connected but will no longer play. To retain
CD changer playback, purchase our JAGCD-HF instead.
See Frequently Asked questions at the end of this guide
Audio module Installation:
1. Remove carpet trim piece surrounding audio rack
2. Remove (4) 8mm nuts securing rack to vehicle.
3. wiring and connections are behind the units
4. Locate single thick black cable from CD changer (connects changer
to Amplifier in premium systems or radio in standard systems)
(See Fig. 1)
Noteworthy: There are similar size/color cables in this area. The
single thick black cable from changer chassis is the correct one.
Fig. 1
5. Remove cable from holding tab and disconnect by grasping both plugs
and gently pulling apart (do not twist)
6. Once disconnected; note Fig. 2- CD changer female connector (right),
amplifier/radio plug (left).
Fig. 2
7. Connect audio module right angle plug (See Fig. 3) to CD changer
connector.
Note: Module right-angle plug (See Fig. 3) does not have an alignment
arrow indicator; however, the imaginary arrow (See Fig. 3) must be
opposite arrow indicator on factory CD changer connector. Once
aligned mate both (do not twist).

Fig. 3
Fig. 3a
8. Connect one end of included 16 ft. 3.5mm male-male audio cable to jack
on Aux box (See Fig. 4), and carefully route audio cable to the center
console.
Fig. 4
Routing audio cable
1. Use a pry tool to open gap between window pillar and rear deck as
seen in Fig. 5. Go into trunk and fish the audio jack (See Fig. 4) through and
into the cabin. (See Fig. 6)
16 ft. Audio Cable
Fig. 5
Fig. 6
2. Pull excess cable and begin tuck under backrest and seat cushion as you
work towards the rear of the center glove box (armrest) as seen in Fig. 7,
Fig. 8 and Fig. 9

Fig. 7
Fig. 8
Fig. 9
3. Continue to use pry tool or fingers to fish wire under center glove box into
storage bin.
4. To remove storage bin: Open the center glove box and remove 2 Philips
head screws from latch cover and two more from hinge then remove the
single screw on retainer bracket.
5. Lift to remove storage bin and set aside.
6. Locate audio plug fed through in step 3 and gently pull excess cable.
Bluetooth module installation
In our test vehicle (2001 XJR Premium Audio), the Bluetooth module was
secured to center armrest sidewall (See Fig. 10) and is our
recommendation. In this area you will also find the factory phone plug and
cigar lighter wiring, either of which can be used to power the Bluetooth
Module (see Fig. 11).
Alert!! Cigar lighter wiring is prone to noise especially if a USB charger is
installed. Locate a noise free power source or purchase a noise filter. In
most instances, this noise is not related to a bad module.
Fig. 10
Fig. 11
Bluetooth Module Red wire requires 12V Accessory Supply (Do not connect
to constant battery supply) and the Black wire must be grounded.

Factory connector/Plug
Ignition supply wire
Ground wire
10-pin Female (white)
Pin 10 (light green)
Pin 6 (black)
10-pin Male (yellow)
Pin 10 (white/green)
Pin 6 (black)
14-pin (yellow)
Pin 13 (Green)
Pin 11n (black)
18-pin male (yellow)
Pin 5 (Green)
Pin 11 (black)
1. If vehicle does not have a phone plug, simply tap into cigar lighter
supply wires under console: White/Blue= 12V ACC, Black=Ground.
Fig. 12
2. Connect 3.5mm audio plug (routed from trunk) to Bluetooth Module
audio jack (See Fig. 13)
Fig. 13
Audio out Jack
3. Connect supplied (3ft.) audio cable (See Fig. 14) to Bluetooth module
“AUX” input jack, (See Fig. 15) and route other end to dash area or
location where audio device will reside (within 3ft).
Fig. 14
3ft. audio cable
Fig. 15
Bluetooth module
4. Connect control/mic plug (See Fig . 16) Bluetooth Module “Mic” input
(See Fig. 15)
Fig. 16
Control button/Microphone
5. Consider where to install control/mic button. Keep in mind the control
button must be within reach of the driver and facing driver for voice
commands and phone dialog (cable is 6ft. long). We recommend
completing the rest of the install prior to securing the
control/mic button to the dash. Once you decide on a location simply
remove tape backing (See Fig. 17) and stick to dash (See Fig. 18)

Fig. 17
Control/Mic button
Fig. 18
Control button/mic on dash
Make sure no ventilation duct is pointed towards the mic.
It is best to mount button facing driver
USB CHARGING PORT
Module USB port is for charging only. Please not this may not provide sufficient
current to charge newer power-hungry devices (e.g., iPhones). If you own one of
these newer devices, consider purchasing our USB-DM3 Smart charging Kit.
You may install the provided USB kit in 1 of 3 ways:
These are also applicable to optional USB Fast Charge Kit.
A. Flush to dash/panel requires drilling a ¾” hole
B. Flush Mount with Support bracket (use this option to mount USB terminal
wherever your installation demands without drilling)
C. Not Mounted- (default)-- Connect your own USB Cable
A. Flush Mount to Dash or Panel (requires drilling)
1. Drill a ¾” hole in the dash or panel using a hole saw, step drill bit or
equivalent (See Fig. 19)
Fig. 19
Step drill bit
2. Insert 3.2ft. (1 Meter) USB male terminal (See Fig. 20) through the ¾”
hole created in step 1 and connect to USB port on Module (See Fig. 21)
Fig. 20
Flush mount 3.2 ft. USB cable
Fig. 21
Module USB port
3. Snap USB head to mounting surface until flush (See Fig. 23)

Fig. 22
USB head
Fig. 23
Flush mounted to dash
4. Tuck and secure any extra wire from moving parts
B. Flush mount with Support Bracket (No drilling)
1. Locate a flat surface at location of choice within 3.2 ft. (1 meter) of
module and mount USB support bracket (See Fig. 24) to surface using
adhesive/tape or screws.
Fig. 24
USB mounting bracket
2. Insert USB male terminal through hole in bracket (See Fig. 25) and
connect to USB port on Module (See Fig. 21)
Fig. 25
3. Snap USB head to mounting plate until flush (See Fig. 26)
Fig. 26
4. Tuck and secure any extra wire away from moving

Bluetooth Pairing and Connection
This process is required the first time you use the JAG-HF. After initial pairing,
the JAG-HF will automatically reconnect with the paired phone upon entering
vehicle.
1. Turn the vehicle ignition to “ON”.
2. The Red LED inside module will begin to flash
3. On incoming/outgoing calls, ring tone plays on car speakers
4. Access your Smartphone Bluetooth menu settings, and search (scan)
for devices.
5. Select the G2 and tap “Connect”
Note: Pairs up to 4 phones but connects to one phone at a time.
Warning! Caller ID and text display are not possible on factory Radio. Operate
Bluetooth device by pressing the control button and your Voice Recognition
applications. Use the radio volume button to control playback level.
Bluetooth Operation
1. Turn ignition to ACC position and radio ON.
2. Press “CD” button on radio. Track or Disc number are displayed only if
they are disc in magazine otherwise “NO MAGAZINE” is displayed (See
Fig. 27)
Fig. 27
Radio must be in “CD Mode” when using the JAG-HF. CD Changer remains
connected but will no longer play.
3. Use Radio button to Adjust Volume
Music Commands
To
Proceed this way
Pause a Song
Press and release button
Resume Play
Press and release button
Skip to next song
Press button twice
Skip to Previous Song
Press button three times
Activate Aux input*
Press button four times
Activate Voice Control
Press/hold button for 2 seconds
Switch from Aux to Streaming Audio
Press and release button

Phone Commands
To
Proceed this way
Answer call
Press and release button
End call
Press and release button
Reject incoming call
Press button twice (call goes to VM)
Cancel outgoing call
Press button twice
Activate Voice Control
Press/hold button for 2 seconds
Notes:
1. If audio playback is distorted or low, adjust volume on phone.
2. To reset Module press and Hold button for 5 seconds (this will not
un-pair phone or erase stored phones)
3. Bluetooth range is approximately 30 ft. make sure device is within
range of receiver
4. Voice command compatible with Apple (Siri), Android (Google Now),
Blackberry (Assistant)
5. *Audio controls not applicable in Aux mode. Use the Aux device built-in
control for music selection and controls.
If successful proceed to reverse the removal steps for Amp rack and center
glovebox console and secure the control button/microphone to dash as per step
#6 in “installing Bluetooth module” instructions.
Congratulations, you’ve just updated your vehicle to support new technology
while preserving the original radio and dash components.
Enjoy!
Frequent asked questions
1. How to I pair a second phone to module?
In order to pair other phones make sure no other phone is paired to module.
Once first device is unpaired, it will be possible to pair another.
2. Can the JAG-HF be installed without removing the radio?
YES; this kit is designed to be installed without removing radio in both
Premium and Standard Systems.
3. What’s the major difference between the JAGCD-HF and JAG-HF?
The JAGCD-HF requires and retains the CD changer, the JAG-HF requires
but does not retain use of the CD changer. (Changer remains connected
but will no longer play and instead an aux input jack is provided)
4. In which model/year Jaguars will the JAG-HF work and where does
the audio module connect?
1998-03 x308 (To changer)
1997 x100 –with Ai-Net style changer only (To changer)
1998-06 x100 (To changer)
5. Will the stereo mute when calls are made or received?
This system will not mute stereo unless radio is in “CD” mode (Bluetooth
mode). If in AM/FM mode, audio system will not mute. In addition, you must
switch radio to “CD” (Bluetooth Mode).
6. Will I be able to use both music and Navigation apps at the same time?
YES! When streaming audio and Navigation apps, music will mute during
navigation guidance and return to previous state when guidance ends. If a
call is made or received, both Navigation guidance and audio streaming are
muted until the call ends.
7. Which audio devices can I connect to the AUX input?
The 3.5mm aux jack on Bluetooth module supports any audio device with a
3.5mm plug (e.g. iPod, MP3, Satellite radio, etc.).
8. Which devices can be charged from USB charging port?
Any and all Bluetooth 2.0 devices requiring 5V Charge including
smartphones, iPod, iPhones, etc.; however, power hungry devices such as
the new iPhones (8-up) may not charge. If you own one of these power-
hungry phones, purchase optional Fast charger option.

9. There is Engine “whine”. What can I do to fix this?
Check ground wires
make sure all connections are snug
If powering module with cigar lighter, try removing device plugged into
cigar port.
Relocate ground wire
Install a noise filter
Feature Comparison :
Feature
JAG-HF
JAGCD-HF
BT45-JAG
A2DIY-JAG98
CD changer retention
X
✓
X
✓
Audio input (aux)
✓
✓*
X
✓
Charging (USB)
✓
✓
X
Optional
Built-in mute feature
X
X
✓
X
Separate microphone
X
X
✓
✓
Requires CD changer
✓
✓
✓
✓
Voice Activation
✓
✓
✓
X
Requires factory phone plug
X
X
✓
X
Plug-n-play installation
X
X
✓
X
Wireless remote control
X
X
X
✓
*Aux input instead of CD changer
Disclaimer
• This product has no affiliation with Jaguar or Apple
• There are no warranties expressed or implied by purchase of this product
• We’re not liable for misuse of this product.
Email [e-mail]
© 1995-Mar-21 Discount Car Stereo, Inc. All rights reserved. Information in this
document is subject to change without notice. Other products and companies referred
to herein are trademarks or registered trademarks of their respective companies or
mark holders.