Discount Car Stereo A2DIY-CTSX Instruction Manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
A2DIY-CTSx
QUICK START INSTALLATION GUIDE FOR SELECT 2003-07 CADILLAC CTS/SRX WITH XM TUNER MODULE

PRODUCT SAFETY & DISCLAIMER
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE
PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY
•This installation guide is provided as a GENERAL installation guide; some vehicles vary and
may require additional steps. We do not accept responsibility for third party labor charges
or modifications. Exercise due-diligence when installing this product.
•We do not accept any responsibility for vehicle damage or personal injury resulting from
the installation of this product.
•Careless installation and operation can result in equipment damage.
Requirements:
XM tuner Module with or without subscription
Introduction:
If your state has enforced hands-free laws and you own a 1st Generation CTS or
SRX with an XM tuner module (with or without subscription), the A2DIY-CTSx is
for you! This kit supports Hands-free calls, music streaming and option to retain
XM playback (if subscribed). The included smart remote pairs with smartphone
to allow users control of music, volume, play/pause and more. In addition, this
kit includes a visor mount microphone with the latest noise cancellation
features. Optional USB “Fast charge” kit to keep current hungry devices charged
while on the road.
Thanks to the A2DIY-CTSx you keep radio, XM subscription while enjoying
Bluetooth features only available on newer cars.
Warning:Vehicle must have an XM tuner module (metal box on rear deck or
rear side panel), with or without subscription; however, if subscription has
expired (with no plans to renew) an AUX input jack is provided
See Frequently Asked question at the end of this guide for more details.
Installation:
Radio removal required to gain access to the connectors.
1. Using a panel removal tool, unclip and remove the top A/C vents panel
(See Fig. 1)
Fig. 1
2. Open ash tray and remove tray. Extract (1) 9/32" screw in tray cavity.
(A Phillips head can be used to remove the screw)
3. Using a panel removal tool, unclip and remove A/C Control/ash tray
assembly below the radio (See Fig. 2)
Fig. 2

4. Remove the (4) 10mm screws securing radio to the dash (See Fig. 3)
Fig. 3
5. Pull radio forward to reveal the connectors (See Fig. 4)
Fig. 4
Radio connectors
6. Disconnect factory 8-pin GRAY plug from radio (See Fig. 4) and
connect to 8-pin BLACK plug on harness (See Fig. 5)
Fig. 5
7. Connect harness 8-pin BLACK plug (See Fig. 6) to radio chamber vacated
in step 6.
Warning: Module is wired to receive 12V from radio amplifier turn on lead
(PIN 2-gray plug); however, radio may not provide enough current to
power both the module and Bose amplifier and as a result the module will
work intermittently in which case module must be powered elsewhere
Disconnect terminal (1) and (2). Connect (2) and (3). ((1) is not used).
Route and connect (3) to 12V accessory supply in vehicle. Accessory power
available under steering column inside driver's lower-dash kick panel. Panel
is supported by three bottom screws and three metal/plastic clips at the
top. Brown wire coming off ignition harness provides ACC power.
Fig. 6
harness

8. Non-XM subscribers: Connect included 3.5mm male to male audio cable
(See Fig. 7) to module “AUX” jack (See Fig. 8) and route other end to front
of the dash where aux device will reside (within 3ft.)
Fig. 7
audio cable
Fig. 8
Module inputs
9. Install microphone to visor or headliner using included visor clip (See
Fig. 10).
Fig. 9
Microphone
Fig. 10a
Visor clip
10. Carefully route microphones plug down side pillar and behind the dash
and connect to module “MIC” input (See Fig. 8)
Excursive caution when routing microphone so to not damage the
cable and ensure no ventilation ducts are pointed towards
microphone.
Visor

Optional charging kit: (not for thumb drives etc.)
Optional “Fast charging”kit can be added to the A2DIY-CTSx. Should you decide
to purchase, we suggest one of 2 connecting options:
A. Flush to dash/panel requires drilling a ¾” hole
B. Flush with Support bracket (Mount USB terminal wherever your installation
demands without drilling)
To add USB charging kit to order, tap the option on order page,
A. Flush to Dash or Panel (drilling required)
1. Drill a ¾” hole in the dash or panel using a step drill bit or equivalent
Step bit
2. Insert male terminal from supplied 3ft. cable (See Fig. 11) through hole
created in step 1 and connect to installation harness charging port
(See Fig. 12)
Fig. 11
Flush mount 3 ft. USB cable
Fig. 12
USB port
3. Snap USB cable head (See Fig. 13) to hole created in step until flush
with mounting surface (See Fig. 14)
Fig. 13
USB head
Fig. 14
Flush mounted to dash
4. Tuck and secure any extra wire from moving parts and test operation

B. Bracket Mount (No drilling)
1. Locate a flat surface at location of choice within 3.2 ft. of module to
mount USB support bracket (See Fig. 15) using adhesive/tape or
screws (included).
Fig. 15
USB mounting bracket
2. Insert USB cable male terminal through hole in bracket (See Fig. 16)
and connect to installation charging port (See Fig. 12)
Fig. 16
3. Snap USB cable head (See Fig. 16) to bracket until flush (See Fig. 17)
Fig. 17
4. Tuck and secure any extra wire away from moving parts and test
operation ( See Bluetooth Pairing and Connection )
Media button operation:
Pairing media button: Ensure Bluetooth is enabled on your device (e.g.,
Smartphone/Tablet etc.)
Press and hold pause/play button (See Fig. 19) until Blue LED begins flashing
Scan smartphone for available devices and select BT009 from list. (Blue LED
turns off).
Fig. 19
Installation:
Attach the button to steering wheel (includes holder) or dashboard using
included double-side tape –your choice.

Operation:
Once paired with smartphone/Tablet, users may perform the following functions
on iOS devices with Bluetooth 3.0 and later or Android 4.0 or later.
Media button functions are NOT applicable to the C5 radio.
0.
Charging:
Media button built-in rechargeable 200mAH battery may last up to 10 days. Use
supplied USB cable to charge. Red LED indicates charging; A full charge is
reached after 2 hours at which time LED turns off.
Module Pairing:
Pairing varies among devices but basic steps are the same. This process is done
upon initial install and will not have to be repeated.
1. Turn ignition and radio “ON”
LED inside module peephole will flash rapidly (pairing mode)
2. On A2DP device: go to Bluetooth Settings
3. Select Bluetooth to enable
4. Tap Scan for devices .
5. Wait for Bluetooth device name (See Fig. 18) to appear and tap it. Once
paired confirmation tone is heard on car speakers
Fig. 18
Noteworthy: On Android devices it may be possible to change device
name to something of your choosing. This may not be possible on newer iOS
devices.
Warning: Caller ID and text are not shown on radio display. Operate
Bluetooth device with smart remote, VR (voice recognition) or built-in
touch controls. Radio buttons can be used to adjust playback level

Operation:
Test Operation:
1. Turn ignition and radio “ON”
2. Press radio “BAND”or “XM ½” soft button to enter Bluetooth mode
3. Launch streaming application (e.g., Pandora, Apple music etc.)
4. Use device built-in control or media button to change tracks, adjust
device volume, pause/play etc.
5. Place test call or ask someone to call. Press media button
“Pause/Play” button to accept/end call.
Use media button Pause/Play to switch between AUX/XM
playback and Bluetooth.
6. If correct operation is confirmed go ahead and reinstall radio.
Notes:
1. If playback is distorted or low, adjust volume level on Smartphone.
2. On incoming calls, ring tone also plays on car speakers
3. Bluetooth range is approximately 30 ft. ensure device is within range
4. Music streaming has priority.
5. *Media button does not control XM/AUX device or radio functions. Use aux
device built-in controls and radio buttons as customary.
Frequent ask questions & troubleshooting:
1. My XM subscription has expired. Will the A2DIY-CTSx work without
subscription?
YES. If subscription has expired (no plans to renew in the future), an AUX
input jack is provided through which users can connect and play portable
audio devices (Mp3 Players, iPod, DVD, iPad etc.) Aux input not available
to XM subscribers.
2. I’m not the original owner and don’t know if vehicle has XM Tuner. How
can I find out without ripping it apart?
Turn radio “ON”. Press “BAND” button repeatedly to cycle through
AM/FM/CD/XM1/2. If only AM/FM is displayed, vehicle does not have
required XM Tuner module and is NOT compatible. On Navigation radios if XM
button is grayed-out, vehicle does not have XM tuner module.
3. Does the A2DIY-CTSx work on all radios?
Works on first generation CTS Navigation and non-Navigation radios. Also
works on SRX non-Navigation only. (not applicable to SRX Navigation
radios).
4. Can I control Smartphone music from radio buttons?
NO; you must continue to use device built-in touch controls or included
media button (remote). Factory radio volume button is used to set
playback level and tone control.
5. Does phone number, song name etc. shown on radio display/screen?
NO. Smartphone or audio device screen must be used to display song and
number details.
6. My XM subscription is active, but how do I listen?
Press BAND or XM1/2 button on radio to enter XM Mode (if not already) XM
should automatically play, otherwise press media button pause/play
7. Will radio mute when I receive or make a phone call?
This system will mute only if radio is in Bluetooth (XM) mode. If in
AM/FM/CD mode, no mute function. In addition, user must switch to “XM”
(Bluetooth Mode) so callers voice can be heard on car speakers.
8. My second phone does not pair or find Bluetooth module?
In order to pair other devices ensure no other is connected this will then
allow another device to pair.

9. Will I be able to use optional USB port to connect and play music from
flash drives?
NO. The USB port is for charging only.
10. What are the major differences between the A2DIY-CTSx and A2DIY-
CTS?
The A2DIY-CTSxworks in vehicles with XM tuner module with or without
subscription. A2DIY-CTS (discontinued) applies to vehicles without XM Tuner
module.
11. My vehicle does not have XM tuner. Will I still be able to add Bluetooth?
NO! Unfortunately, module for this application has been discontinued.
Disclaimer
• This product has no affiliation with Cadillac
• We’re not liable for misuse of this product.
•We recommend professional installation
For help email [e-mail]
© 1995-September 7, 2021 Discount Car Stereo, Inc. All rights reserved. Information in this
document is subject to change without notice. Other products and companies referred to herein
are trademarks or registered trademarks of their respective companies or mark holders.