Discount Car Stereo A2DIY-HON03 User manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
A2DIY-HON03
TriplePlayMediaBluetoothandAUXInstallationGuideforSelect2003-12Honda&Acura
Created:January16,2019
RevisedMarch29,2020

Introduction:
If your 2003-12 Honda or Acura does not include Bluetooth our A2DIY-HON03
“triple play” upgrades these vehicles to support (1) Bluetooth Hands-Free
calling, (2) music streaming from any smartphone or Tablet with A2DP and HF
profile. In addition to Bluetooth, it includes a 3.5mm (3) AUX input jack which
user can connect and play portable audio devices (e.g. Mp3 Players, satellite
radio kit, iPods etc.). The included wireless remote allow user to change tracks,
volume and more while keeping eyes on the radio. An optional USB charging
port supplies up to 3A charging power for those power-hungry devices. Keep
the radio and car you love while enjoying Bluetooth features only available on
newer cars.
See Frequently Asked question at the end of this guide for details.
Installation: (To radio)
Remove radio from dashboard to gain access to connector. (Vehicle
specific radio removal instructions are not part of this guide, but may be
available upon request)
Older 14-pin blue plug radios (See Fig. 2) are not compatible.
Compatible radios must have 14-pin white connector as seen in
Fig. 1.
1. Locate 14-pin white connector (See Fig. 1) (usually on back or bottom
of the radio)
Fig. 1
Radio 14-pin port
Fig. 2
Honda 14-pin plugs
2. Connect module 14-pin plug (See Fig. 2) to radio 14-pin connector.
Note: If vehicle has Navigation the HON03-F/MM t-harness (sold
separately) is required to retain GPS guidance (prompts)
3. Connect supplied 3.5mm audio cable (See Fig. 4) to module “AUX” jack
(See Fig. 3). Route other end to front of the dash or wherever Aux
device will reside (within 3 ft.)- Skip this step if not using the aux jack.
Fig. 3
Module input jacks

Fig. 4
Module
4. Connect push-to talk button 1/8” plug to module “CTR” jack (See Fig.
3), route button to dash area (cable is 6ft. long); remove tape backing,
clean area and secure to dash. (See Fig. 5)
Fig. 5
push-to-talk button
Noteworthy: Push-to-talk button is not required for Android applications
because the wireless remote play/pause button replicates its function (e.g.
start/end phone call and switch between Bluetooth and aux input
5. Secure microphone (See Fig. 6) to visor or headliner using included
visor clip (See Fig. 6a) 6)
Fig. 6
Microphone
Fig. 6a
Visor clip
6. Carefully route microphones right angle plug (See Fig. 6) down pillar,
under driver kick panel to radio cavity and connect to module “MIC”
jack (See Fig. 3)
Be cautious when routing microphone cable. Also ensure no
ventilation ducts are pointed towards microphone.
Wireless remote control
Pairing wireless remote: The included wireless remote must be paired
with Smartphone for media control functions (does not control radio functions).
The remote pairs with multiple devices but can only operate one at a time.
Follow 3-step pairing process below:

Installing wireless remote:
Wireless remote can be installed on dashboard using provided double side tape
or to steering wheel.
Remote control operation:
With wireless remote paired to smartphone, users may perform the following
functions on devices with iOS7.0 and higher and Android 4.4 and higher.
In addition to above:
To answer/end call press Play/Stop button (Android only)
To switch from streaming/AUX press, Play/Stop button (Android only)
To answer/end call press push-to-talk button (Apple and/or Android)
To switch from streaming/AUX press push-to-talk button (Apple and/or
Android)
Notes:
1. If playback is distorted or low, adjust volume on Bluetooth device.
2. On incoming calls, ring tone plays on car speakers
3. Bluetooth range is approximately 30 ft. make sure device is within
range
4. Music streaming has priority.
5. *Wireless remote does not control Aux device. Use radio buttons to
control changer as customary and AUX device buttons for music
selection and controls.
Pairing:
Pairing varies among devices but basic steps are the same. This process is
done upon initial install and will not have to be repeated.
1. Turn ignition and radio “ON”
Blue LED through module peephole will flash (pairing mode)
2. On A2DP device: go to Bluetooth Settings
3. Select Bluetooth and turn on
4. Tap Scan for devices .
5. Wait for Bluetooth device name (LANNI) to appear and tap it. Once
paired confirmation tone is heard on car speakers
Test Operation:
1. Turn ignition and radio “ON”
2. Press “DISC” “CD” or “XM/AUX” button on radio
3. Launch smartphone music streaming application
4. Use wireless remote to change tracks, adjust device volume, pause etc.
5. Place call or ask someone to call. Use push-to-talk button to answer
call (iPhone and Android) or press pause/play button on remote
(Android only)
Note: The push-to-talk button can be used to answer/end calls on both
Apple and Android devices, however wireless remote pause/play
button only works to answer/end calls on Android devices.
6. If correct operation is confirmed go ahead and reinstall radio.

Frequent asked questions
1. Does the A2DIY-HON03 work on all Honda radios?
NO; The A2DIY-HON03 works on select 2003-12 Honda and Acura CD
Changer/XM ready radios OR vehicles. XM, External CD Changer must be
disconnected and will no longer function.
2. My radio has a built-in 6 CD Changer, will the A2D-HON03 Work?
YES so long it also has a 14-pin port for external devices
3. Will the A2DIY-HON03 disable the radio built-in CD Changer?
NO; CD changer built-into the radio remains functional.
4. Can radio buttons be used to control smartphone functions?
NO; You must use audio device built-in controls to browse music library or
included wireless remote control limited functions describe on page 3.
5. Will I be able to make phone calls using this module?
NO; the A2D-HON03 does not supports Hands-Free Calls.
6. My vehicle has factory GPS. Will it continue to work with this module?
YES, but to retain Navigation prompts you must purchase our HON03-F/MM
T-harness (sold separately)
7. How do I listen to AUX device?
Connect AUX device to module input jack, press “DISC” “CD” or “XM/AUX”
button on radio to enter Bluetooth mode, then press push-to-talk button
(Android or Apple) or play/pause on remote (Android only)
Note: A paired device is not required for AUX to function.
8. Will radio mute when I receive or make phone calls?
Muting is possible only if radio is in “Bluetooth” mode. If in AM/FM or CD
mode; muting is not possible. In addition, user must place radio in
“Bluetooth”for caller to be heard on car speakers.
9. My second phone does not pair or find Bluetooth module?
In order to pair second devices ensure no other device is currently
paired. Once that device is un-paired, module will enter discovery mode and
ready for paring.
10. How to I remove radio from the dash?
Due to the many applications for this module, vehicle specific radio removal
instructions are not part of this guide, but may be available upon request.
Simply click the support email link below and include vehicle model/year.
Disclaimer
• This product has no affiliation with Honda, Acura.
• We’re not liable for misuse of this product.
•We recommend professional installation.
Email [email protected]
© 1995-Mar-20 Discount Car Stereo, Inc. All rights reserved. Information in this document is
subject to change without notice. Other products and companies referred to herein are
trademarks or registered trademarks of their respective companies or mark holders