Discount Car Stereo AAI-SONY User manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
AAI-SONY
INSTALLATION GUIDE FOR SONY AUX READY RADIOS

PRODUCT SAFETY & DISCLAIMER
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE
PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY
•This installation guide is provided as a GENERAL installation guide, some vehicles vary and
may require additional steps. We do not accept responsibility for third party labor charges
or modifications. Exercise due-diligence when installing this product.
•We do not accept any responsibility for vehicle damage or personal injury resulting from
the installation of this product.
•Careless installation and operation can result in equipment damage.
Requirements:
Sony CD Changer controlling radio
Introduction:
Portable audio products are everywhere, reflecting demand from active people
all over the world to take their music with them. IPods, iPads, MP3's, portable
DVDs compact stereos etc. let you enjoy music at the beach, picnic, back yard
and in the car. The AAI-SONY is compatible with all Sony CD changer controlling
radios and takes the place of the CD changer or satellite radio (if installed).
This adapter converts the Unilink CD changer port to 3.5mm, 30-pin dock, Apple
Lightning or USB.
Apple lightning and USB terminal are compatible with: iPhone 5(C, S)- 12, iPod
Touch (5G), iPad(4G), iPad Mini(1G), iPad Mini with Retina display etc.
Warning: Sony radio control buttons (except volume and tone controls) do not
apply. Use audio device built-in controls and display for music selection and
controls.
Installation:
Remove Sony radio from dashboard to gain access to the connectors. Refer to
Fig. 1
Fig. 1
3.5mm installation
1. Connect audio cable left + right to radio BUS AUDIO INPUTS
2. Connect Unilink BUS adapter to radio Unilink CD CHANGER PORT
3. Route 3.5mm plug from audio cable to dash area or within 6 ft.
Apple 30-pin dock installation
1. Connect adapter cable left + right RCA’s to radio BUS AUDIO INPUTS
2. Connect (Splice) adapter cable red wire to Sony radio accessory wire
(usually red)
3. Connect (Splice) adapter cable black wire to Sony radio ground wire
(usually black)

4. Connect Unilink BUS adapter to radio Unilink CD CHANGER PORT.
5. Route 30-pin dock to front of dash area within 6 ft.
Apple iOS lightning cable
1. Connect adapter cable left + right RCA’s to radio BUS AUDIO INPUTS
2. Connect (Splice) adapter cable red wire to Sony radio accessory wire
(usually red)
3. Connect (Splice) adapter cable black wire to Sony radio ground wire
(usually black)
4. Connect Unilink BUS adapter to radio UNILINK CD CHANGER PORT.
5. Route Lightning plug to dash area or to within 4 ft.
USB cable terminal
1. Connect adapter cable RCA’s to radio BUS AUDIO INPUTS
2. Connect (Splice) adapter cable red wire to Sony radio accessory wire
(usually red)
3. Connect (Splice) adapter cable black wire to Sony radio ground wire
(usually black)
4. Connect Unilink BUS adapter to radio UNILINK CD CHANGER PORT.
Terminal mount option:
A. Flush to dash/panel requires drilling a ¾” hole in the dash
B. Flush with Support bracket (use this option to mount USB terminal
wherever your installation demands without drilling)
C. No USB Mount- (default)
A. Flush to Dash or Panel (req. drilling)
1. Drill a ¾” hole in dash or panel using a step drill bit or equivalent (See
Fig. 13)
Fig. 2
Step drill bit
2. Insert 3ft. USB cable (See Fig. 14) through ¾” hole created in step 1
Fig. 2
3 ft. USB cable
3. Snap USB head (See Fig. 3) until flush with mounting surface (See Fig.
4)
Fig. 3
Flush mount USB Terminal

Fig. 4
Flush mounted to dash
4. Tuck and secure any extra wire from moving parts and proceed to test
operation
B. USB Bracket Mount (No drilling)
1. Locate a flat surface at location of choice within 3.2 ft. of radio to
mount USB bracket (See Fig. 5) to surface using adhesive/tape or
screws (included)
Fig. 5
USB mounting bracket
2. Insert USB male terminal through hole in bracket (See Fig. 6)
Fig. 6
3. Snap USB head to bracket until flush (See Fig. 7)
Fig. 7
5. Connect USB Male terminal to USB adapter cable
6. Tuck and secure any extra wire away from moving parts and test operation

Operation:
Test operation prior to re-installing radio:
1. Connect iPod, iPhone or MP3 player to 3.5mm, 30-pin, lightning or USB
terminal.
2. Verify Apple device is charging (iPod dock, Lightning or USB only)
3. Do not proceed if device does not charge; instead, verify power and ground
connection.
4. Turn radio “ON” and enter CD changer mode. (See Sony manual)
5. Select track from audio device music library.
6. Audio device should be heard on car speakers.
7. If correct operation is confirmed re-install radio.
Warning: Playlist and Track selection *NOT* possible from Sony radio. Use audio
device built-in controls to access music files.
Not all Sony radios have CD changer controls. Ensure radio in your vehicle has
CD changer controls; otherwise, the AAi-SONY will NOT WORK.
USB option is exclusive to Apple IOS devices (except Nano 7G)—Will not play
other Apple devices (e.g., 30-pin dock connector nor Android devices)
Disclaimer
• This product has no affiliation with Blaupunkt or Apple
• We’re not liable for misuse of this product.
•We recommend professional installation.
Email [e-mail]
© 1995-Aug-21 Discount Car Stereo. All rights reserved. Information in this document is
subject to change without notice. Other products and companies referred to herein are
trademarks or registered trademarks of their respective companies or mark holders.