Discount Car Stereo CHRY-AUX Instruction Manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
CHRY-AUX
QUICK START INSTALLATION GUIDE FOR SELECT 1995-02 CHYSLER CD CHANGER READY RADIOS
created August 10, 2015
Revised: September 5, 2021

PRODUCT SAFETY & DISCLAIMER
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE
PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY
•This installation guide is provided as a GENERAL installation guide, some vehicles vary and
may require additional steps. We do not accept responsibility for third party labor charges
or modifications. Exercise due-diligence when installing this product.
•We do not accept any responsibility for vehicle damage or personal injury resulting from
the installation of this product.
•Careless installation and operation can result in equipment damage.
Requirements:
cd changer controlling radio
Introduction
Any car owner adamant about keeping the factory radio and maintaining vehicles
original look and feel will be pleased to find this adapter. The CHRY-AUX updates
the vehicle owner to connect and play modern media audio devices such as MP3
players, Smartphones etc. without changing the radio. The CHRY-AUX auxiliary
input adapter connects to the radios 8-pin CD changer port which guarantees to
best possible sound. Factory CD changer (if present) must be disconnected.
See Frequently Asked question at the end of this guide for details.
Installation
Radio removal required to gain access to connectors.
Vehicle specific radio removal is not part of this guide; however, these can be
made available upon request.
1. Connect adapter 8-pin plug (See Fig. 1) to “CD”changer connector on
radio (See Fig. 2)
Fig. 1
8-pin plug
Fig. 2
Radio connector
2. Connect one end of supplied 3.5mm audio cable (See Fig. 3) to input
jack on adapter (See Fig. 4), route cable end to front of the dash or
wherever audio device will reside (within 3 ft.)

Fig. 3
3 ft. Aux cable
Fig. 4
3.5mm jack
3. Secure adapter box and proceed to next step.
Operation
1. Turn ignition to “ACC” and radio “ON”
2. Press radio “MODE”button. Radio display changes to Disc1 Track 1 as
seen in Fig. 5
Fig. 5
3. Use radio volume control button to set playback level.
Warning: Playlist and Track selection is *NOT* possible from Chrysler
radio buttons. Use audio device built-in controls or wireless remote to
access and control audio files and applications.
4. If correct operation is confirmed go ahead and reinstall Radio.

Frequent ask questions & troubleshooting
1. Will the CHRY-AUX work on all Chrysler 8-pin CD changer port radios?
NO; this adapter works on 2 Chrysler changer controlling radios:
1. Square face Tape radio: With Mode button, 5 band EQ, "Disk Up" on
preset # 1, “Disc down” on preset #5, 8-pinCD changer port as seen here
2."Square face Tape radio: With MODE/EJECT button, 6 radio presents,
Bass and Treble slider controls, "DIRECT DISC SELECT 1-6" printed above
radio presets as seen here
Also works on European radio model P04704345.
2. My radio has most features listed in question 1. Will the CHRY-AUX
work?
NO; The compatible radio must have all features listed to be compatible
3. Will I have to disconnect the factory CD changer?
YES, this adapter uses the CD changer 8-pin port. Any and all devices using
this port will need to be disconnected. Purchase our A2D-CHRY to retain CD
changer.
4. Can I use the radio to control songs and display text?
NO, this adapter does not control audio device (e.g., smartphone). Use
device built-in control and display just as you would in portable mode.
Disclaimer
• This product has no affiliation with Chrysler
• We’re not liable for misuse of this product.
•We recommend professional installation
email [email protected]
© 1995-Sep-21 Discount Car Stereo, Inc. All rights reserved. Information in this document is
subject to change without notice. Other products and companies referred to herein are
trademarks or registered trademarks of their respective companies or mark holders.