Discount Car Stereo A2D-SRX Instruction Manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
A2D-SRX
QUICK START INSTALLATION GUIDE FOR CADILLAC 2003-06 SRX WITH NAVIGATION & XM TUNER MODULE
created August 10, 2015
Revised: June 18, 2021

PRODUCT SAFETY & DISCLAIMER
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE
PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY
•This document is provided as a GENERAL installation guide, some vehicles vary and may
require additional steps. We do not accept responsibility for third party labor charges or
modifications. Exercise due-diligence when installing this product.
•We do not accept any responsibility for vehicle damage or personal injury resulting from
the installation of this product.
•Careless installation and operation can result in equipment damage.
Introduction:
Are you looking to stream music application in your 1st Generation SRX with
Navigation radio and XM tuner module? Our A2D-SRX Bluetooth module, allows
these vehicles owners to stream music applications (e.g., Pandora, Apple Music,
SiriusXM, Spotify etc.) from Smartphone, Tablet, Kindle etc. through the
Navigation radio XM port. A wireless connection means no wires, clutter or
complicated setup. The two requirements for this module to work are:
1. Navigation radio
2. XM Tuner Module (with or without subscription).
If XM subscription is active, select “Subscribed”, if expired, select “Not
subscribed”; however, if not currently subscribed but plan to renew in the
future, select “Subscribed” otherwise XM will not play upon activation.
To verify vehicle has required XM Tuner Module; press radio “BAND” button. If
XM1/2 softkeys is available (not grayed out), vehicle has required XM Tuner
Module and compatible with the A2D-SRX.
See Frequently Asked question at the end of this guide for details.
Installation:
Navigation radio must be removed from dashboard to gain access to connectors.
1. Using a panel removal tool, unclip and remove the top A/C vents panel
(See Fig. 1)
Fig. 1
2. Open ash tray and remove tray. Extract (1) 9/32” (7mm) screw from
tray cavity.
3. Using panel removal tool, unclip and remove A/C control/ash tray
assembly below radio (See Fig. 2)
Fig. 2
4. Remove (4) 10mm bolts securing radio to the dash (See Fig. 3)

Fig. 3
5. Pull radio forward to reveal connectors (See Fig. 4)
Fig. 4
Radio connectors
6. Disconnect factory 16-pin plug from navigation radio (See Fig. 4)
7. Connect factory 16-pin plug removed from radio in step 6, to 16-pin
connector on adapter harness (See Fig. 5).
Fig. 5
connector
8. Connect 16-pin plug from adapter (See Fig. 6) to radio cavity vacated
in step 6
Fig. 6
plug
9. Connect single red wire to a 12V Accessory supply wire in vehicle. Do
not connect to 12V constant supply (battery)
Tip:Accessory (ACC) power is available on SRX ignition harness (found
under steering column). Remove panel under steering column and tap
brown wire coming off the ignition harness. This wire will power the adapter
when ignition is “ON”.

Pairing:
Pairing process varies among devices but basic steps are the same. This
process is done upon initial install and will not have to be repeated
1. Turn Ignition and navigation radio “ON”
LED inside adapter peephole will flash (pairing mode)
2. On A2DP device (e.g., Smartphone): Go to Settings, Wireless &
Networks, Bluetooth Settings
3. Select Bluetooth and turn on.
4. Then select Bluetooth settings
5. Tap Scan for devices .
6. Wait for the Bluetooth device name to appear and select it. (One of two
devices will display)
LED inside adapter peephole will glow steady (paired)
Test Operation:
1. Turn ignition and navigation radio “ON”
2. Press “BAND” button and select XM1/2
3. Launch Smartphone or Tablet music application.
4. Use radio volume control button to set the playback level.
Playlist and Track selection *NOT* possible from
buttons or display. Use audio device (e.g., Smartphone)
built-in controls or optional wireless remote to access
and control audio files.
5. If correct operation is confirmed go ahead and reinstall radio.
Active XM Subscribers:(Available only if “Subscribed” was selected during
checkout)
1. To listen to XM:
Press “BAND” button on radio, pause streaming or disable Bluetooth on audio
device. XM playback will resume.
2. To return to streaming
Un-pause streaming or re-enable Bluetooth in audio device settings screen.
Note: Music streaming has priority and remains until Bluetooth is paused or
disabled on audio device. XM Playback is only possible if music streaming is
paused, Bluetooth is disabled or device is out of range.

Optional Smart Remote:
Smart remote is optional and not required for the A2D-SRX operation,
however instead of fumbling with phone, simply press buttons while keeping
eyes on the road. The remote can also be used at home. (Does not control
factory radio operations)
Remote control functions:
1. Control music wirelessly
2. Activate VR commands (Google only.)
3. Track up/down
4. Volume up/down
Pairing Bluetooth remote:
Smart remote operation:
Use smart remote to perform the following functions on any iOS7.0 and higher
or Android 4.4 and higher.
Contents:

Frequently asked questions
1. Will the A2D-SRX work in SRX without Navigation?
NO; Works only in 1st generation SRX with Navigation radio and XM Tuner
Module (a separate box installed in rear quarter panel)
2. Will the A2D-SRX work in Bose systems?
YES; works in Bose and Non-Bose applications
3. My XM subscription has expired, will the A2D-SRX still work?
YES; as long as vehicles has an XM Tuner module. (With or without
subscription) Select “Not subscribed” option when ordering or if you plan to
renew at a later date, select Subscribed otherwise XM will not play upon
activation.
4. My XM subscription is still active; will the A2D-SRX still work?
YES; Retain XM playback by selecting “Subscribed”from options because
“Not subscribed” version will NOT retain XM playback
5. I’m not the original owner and don’t know if vehicle has required XM
Tuner module. How can I find out without ripping the car apart?
XM tuner module is located behind rear side quarter panel however, you
may also check by turning on the radio, and press “BAND” button. If XM1/2
softkey is available (not grayed out), your vehicle has required XM module.
6. Can I install the A2D-SRX without removing the radio?
NO; The A2D-SRX requires radio removal. As an alternate, purchase our
A2D-GM3x which connects at the XM Tuner module location in quarter
panel.
7. Can I use the A2D-SRX to make/receive phone calls?
NO;The A2D-SRX supports music streaming only, Not for phone calls.
Disclaimer
• This product has no affiliation with GM
• We’re not liable for misuse of this product.
•We recommend professional installation
For help please email [email protected]
© 1995-Jun-21 Discount Car Stereo, Inc. All rights reserved. Information in this
document is subject to change without notice. Other products and companies referred
to herein are trademarks or registered trademarks of their respective companies or
mark holders.