Divio 4CH NVR User manual

 


1
4 /8/16 CH NETWORK VIDEO RECORDER
Quick Installation Guide
4/8CH NVR Front Panel
The front panel includes:
1. Power button: Power On/Off NVR.
2. IR receiver: Receiver for IR remote.
3. Status indicators:
: HDD Indicator turns on when system is accessing hard disk
: Alarm indicator turns on when alarm is detected.
:: Exception indicator turns on when system exception alert is detected, such as disk full, disk
error, no disk, network disconnect, illegal login, disk over temperature, fan fail, network fail,
power loss and IP conflict.
: Rec indicator turns on when NVR is recording.
: WAN indicator turns on when NVR is connecting to WAN port.
: LAN indicator turns on when NVR is connecting to LAN port.
4. CH1~CH8 : Indicators turn on when the video is connected to the system.
5. USB port : USB port for connecting devices, such as USB mouse or USB flash device.
4/8CH NVR Rear Panel
The rear panel connectors include:
1. Audio In: Connect the microphone or camera audio output to the audio input connector.
2. Audio Out: Connect a speaker or other audio output device to the audio output connector.
3. VGA: Connect a VGA monitor to the VGA output connector.
4. HDMI: Connect a HDMI monitor to the HDMI output connector.
5. LAN: Connect hub with IP cameras via RJ-45 network cable.


 


2
6. WAN: Connect NVR to Internet via a RJ-45 network cable.
7. RS485 socket: For RS485 PTZ control.
8. Alarm In: Connect to 4 or 8 alarm inputs to the alarm input connectors.
9. Alarm Out: N.C or N.O type alarm signal out.
10. Power: Plug the DC12V power source into the power socket.
4/8CH NVR Packing
The package contains the following items:
-Network video recorder x 1 -IR remote control x 1 (optional)
-User manual/Quick Install/CMS disc x 1 -Quick Install Paper x1
-Poweradapterx1 -Powercordx1
-Alarm terminal block x 4 -SATA connection cable x 3
-Hard drive mounting bracket x 6 pcs -Screws for mounting bracket x 15 pcs
-Screws for mounting hard drive x 15 pcs
4/8CH NVR Installation and connections
4/8CH NVR Hard drive Installation:
Follow the steps to install or replace the hard disk,
Step1. Take out the screws on the back panel of the unit.
Step2. Slide opens the top cover.
Step3. Use the HDD mounting screws attached in the accessory pack to fix the mounting brackets
to the hard drive.
Step4. Connect SATA & Power wire to Hard Disk and put it on right position of the case. Use the
HDD mounting screws attached in the accessory pack to fix the hard drive with bracket firmly on to
the chassis.
Step5. Connect the SATA cables to the SATA connectors on the main board.
(Step3)
4/8CH NVR Connections:
Primary connection:
1. Connect the IP cameras to the LAN port through the hub. Power up the IP camera before
powering the NVR.
2. Connect at least one proper monitor to the HDMI or VGA output. (Supporting display mode
from 1024x768 up to 1920x1080)
3. Connect an USB mouse to a USB port.
Optional connections:
1. Connect the second monitor to the other monitor output. (Supporting display mode from


 (Step5)

 


3
1024x768 up to 1920x1080)
2. Connect the audio signal to the AUDIO IN RCA input.
3. Connect the AUDIO OUT RCA output to the monitor or an audio speaker.
4. Connect up to 8 ALARM IN inputs through the supplied terminal blocks.
5. Connect the ALARM OUT output through the supplied terminal blocks.
6. Connect a pan/tilt/zoom control unit to the RS-485 port through the supplied terminal block.
7. Connect to your network through the Ethernet port.
Powering up:
1. Connect the power unit to the AC power outlet.
2. Connect the DC power cord to the 12VDC connector on the unit.
16CH NVR Front Panel
The front panel includes:
1. Power button: Power On/Off NVR.
2. IR receiver: Receiver for IR remote.
3. Status indicators:
: HDD Indicator turns on when system is accessing hard disk
: Alarm indicator turns on when alarm is detected.
:: Exception indicator turns on when system exception alert is detected, such as disk full, disk
error, no disk, network disconnect, illegal login, disk over temperature, fan fail, network fail,
power loss and IP conflict.
: Rec indicator turns on when NVR is recording.
: WAN indicator turns on when NVR is connecting to WAN port.
: LAN indicator turns on when NVR is connecting to LAN port.
4. CH1~CH16 : Indicators turn on when the video is connected to the system.
5. USB port : USB port for connecting devices, such as USB mouse or USB flash device.
16CH NVR Rear Panel
The rear panel connectors include:


 


4
1. Power: Plug the power cord into the power socket.
2. Alarm Out: N.C or N.O type alarm signal out.
3. Alarm In: Connect to 16 alarm inputs to the alarm input connectors.
4. RS485 socket: For RS485 PTZ control.
5. Audio Out: Connect the microphone or camera audio output to the audio input connector.
6. Audio In: Connect the microphone or camera audio output to the audio input connector.
7. HDMI: Connect a HDMI monitor to the HDMI output connector.
8. VGA: Connect a VGA monitor to the VGA output connector.
9. LAN: Connect hub with IP cameras via RJ-45 network cable.
10. WAN: Connect NVR to Internet via a RJ-45 network cable.
11. USB port: USB port for connecting devices, such as USB mouse or USB flash device.
12. Ext. IR: Connect IR extension cable to Ext. IR port to increase the range of an infrared signal.
16CH NVR Packing
The package contains the following items:
-Network video recorder x 1 -IR remote control x 1 (optional)
-User manual/Quick Install/CMS disc x 1 -Quick Install Paper x1
-Powercordx1 -Alarmterminalblock10Px2
-SATA connection cable x 6 -Alarm terminal block 6P x 2
-Hard drive mounting bracket x 6 pcs -Screws for mounting bracket x 15 pcs
-Screws for mounting hard drive x 28 pcs
16CH NVR Installation and connections
16CH NVR Hard drive Installation:
Step1. Remove the hard disk mounting bracket and hard disk screws from the accessory pack.

 


5

Step 2. Fix the harddisk on to the harddisk mounting bracket and fix the screws on to the screw holes as
indicated in the diagram. Each set of harddisk brackets can mount 2 harddisks.


Step 3. Remove the screws on the top cover and slide open the top cover. Place the harddisks with
brackets into the unit and use the attached harddisk mounting screws to fix the brackets on to the
unit.
Step 4. Connect the SATA cables to the SATA connectors on the main board. Please refer to the below for
the hard drive port numbers and connect the HDD accordingly. The NVR will recognize the hard
drives according to the SATA port numbers for the disk management.

 


6
Step 5. Connect the hard disk power cable and SATAcable on to each hard disk. Reassemble the top cover
and fix the screws back once all the hard disks are well installed.


 


7
16CH NVR Connections:
Primary connection:
1. Connect the IP cameras to the LAN port through the hub. Power up the IP camera before
powering the NVR.
2. Connect at least one proper monitor to the HDMI or VGA output. (Supporting display mode
from 1024x768 up to 1920x1080)
3. Connect an USB mouse to a USB port.
Optional connections:
1. Connect the second monitor to the other monitor output. (Supporting display mode from
1024x768 up to 1920x1080)
2. Connect the audio signal to the AUDIO IN RCA input.
3. Connect the AUDIO OUT RCA output to the monitor or an audio speaker.
4. Connect up to 16 ALARM IN inputs through the supplied terminal blocks.
5. Connect the ALARM OUT output through the supplied terminal blocks.
6. Connect a pan/tilt/zoom control unit to the RS-485 port through the supplied terminal block.
7. Connect to your network through the Ethernet port.
Powering up:
1. Connect the power cord to the power socket.
※ It is suggested to installed tested hard disk to ensure the recording performance, Please refer to
the below for the tested compatible hard disk model list.

 


8
First-time use - Full Auto Install Mode
When the first time connect IP cameras to the NVR, the NVR will pop up install wizard window. NVR
provides Plug and Play feature if user installs NVR in “Full Auto Install” mode. Click “Full Auto Install”
and then the NVR will automatically configure IP address of a camera connected by LAN. The NVR will
then detect the IP camera and display image on screen.
The connection of the LAN port is for IP cameras. The connection of the WAN port is for the NVR to
Internet. This mode is suitable when the LAN is connected to a hub.
Please click “Full Auto Install” and the NVR will automatically configure IP cameras connected by LAN.
After few seconds, the NVR will detect the IP cameras and display images.
＊The connected IP cameras must be specific IP camera models.
＊The IP camera is powered on before the NVR is power on.
Note: User also can go to Configuration→System→Device→Install Wizard, to bring up the Install
Wizard.
If the NVR does not configure the IP camera automatically, please recheck the conditions as listed
above and rerun the Install Wizard when it’s ready.


 


9
Rear Panel Connection

 


10
