DKS 1812 Classic Operating instructions

UL Listed
Copyright 2009 DoorKing, Inc.All rights reserved.
Copyright 2014 DoorKing, Inc. All rights reserved.
Date Installed:
Installer/Company Name:
Phone Number:
Leave Manual with Owner
Circuit Board
Serial Number
and Revision Letter:
7
8 9
4 5 6
1 2 3
0
7
8 9
4 5 6
1 2 3
0
7
8 9
4 5 6
1 2 3
0
Wall Mount
Flush Mount
Surface Mount
Installation/Owner’s Manual
Model 1812 Classic
Model 1812 Classic
Model 1812 Classic
Use this manual for circuit board 1871-010 Revision S or higher.
Control a main door and gate.
Residential Telephone Intercom/Access Control System
Push Button
Push Button
To Call
To Call
Push Button
Push Button
To Call
To Call
1812-065-V-12-14

1812-065-V-12-14 1
SPECIFICATIONS
Features
Surface Mount Wall Mount Flush
Mount
DoorKing, Inc. reserves the right to make changes in the products described in this manual without notice and without obligation of DoorKing, Inc. to notify any persons of any such
revisions or changes. Additionally, DoorKing, Inc. makes no representations or warranties with respect to this manual. This manual is copyrighted, all rights reserved. No portion of this
manual may be copied, reproduced, translated, or reduced to any electronic medium without prior written consent from DoorKing, Inc.
•Unique telephone communication system allows homeowners to use their telephone as an intercom to speak to a guest at a
front door or gate, and to control access to their property.
•Unit connects directly to the homeowners existing telephone line. No additional monthly expense for a second telephone line.
•Built in call waiting assures that incoming calls or guest calls are not missed.
•Two internal relays allow the system to control a main entry gate plus a pedestrian access gate.
•Built-in clock / calendar provides the following time related functions:
1. Do-not-disturb time zone.
2. Four hold-open time zones.
3. Access code time zone.
4. Call forward time zone.
5. Flash access code.
•Unit can be programmed to work with PBX and KSU phone systems.
•Optional secondary keypad can be added for remote access code activation of door or gate.
For Model 1812 Classic with circuit board 1871-010 Rev S or higher ONLY.
7
7
8
8
9
9
4
4
5
5
6
6
1
1
2
2
3
3
0
0
7
7
8
8
9
9
4
4
5
5
6
6
1
1
2
2
3
3
0
0
7
7
8
8
9
9
4
4
5
5
6
6
1
1
2
2
3
3
0
0
PushButton
PushButton
To Call
ToCall
Push Button
PushButton
ToCall
ToCall
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1

1812-065-V-12-14
2
7
7
8
8
9
9
4
4
5
5
6
6
1
1
2
2
3
3
0
0
SPECIFICATIONS
Surface Mount Dimensions
7
7
8
8
9
9
4
4
5
5
6
6
123
0
0
1
1
1
1
2
2
2
2
3
3
3
3
3
3
10” 5.25”
6.125”
2.5”
2.5”
1.125” Dia
2.875”
1.125”1.125”
1.75”
875” Dia
5”
3”
Wall Mount Dimensions
7
7
8
8
9
9
4
4
5
5
6
6
1
1
2
2
3
3
0
0
7.325”
10.75” 3.5”
2.5”
2.5”
1.125” Dia
5.375”
3.375”
7
7
8
8
9
9
4
4
5
5
6
6
1
1
2
2
3
3
0
0
Push Button
Push Button
To Call
ToCall
Push Button
Push Button
To Call
To Call
Side ViewFront View
Bottom View
Bottom View
Back View
Side ViewFront View Back View

1812-065-V-12-14 3
Rough-In
Box
SPECIFICATIONS
Flush Mount Dimensions
7
7
8
8
9
9
4
4
5
5
6
6
123
0
0
1
1
1
1
2
2
2
2
3
3
3
3
3
3
7.5”
6.25” 7.25”
9.25”
5”
3.5”
3.5”
10.25”
10”
12”
4.5” 4.25”
2.625”
.875” Dia
5” 2.5”
1.25” Dia
Rough-In Box
Rough-In Box
Rough-In Box
Flush Box
Flush Box
Side Views
Bottom Views
Front Views
Bolt holes (4) to secure flush box
inside rough-in box.
Flush Box
Flush Box
Flush
Box
7
7
8
8
9
9
4
4
5
5
6
6
1
1
2
2
3
3
0
0
Push Button
Push Button
To Call
ToCall
Push Button
Push Button
To Call
To Call

1812-065-V-12-14
4
SPECIFICATIONS
Features
Surface Mount Dimensions
Wall Mount Dimensions
Flush Mount Dimensions
Important Notices FCC - United States, DOC - Canada
General Information Installation Guidelines and Safety Information
SECTION 1 - INSTALLATION
1.1 Mount the 1812 Classic
Different Mounting Configurations of the 1812 Classic Models
1.2 Install By-Pass Board for “Telephone Mode” Configurations
1.3 Telephone Line Wire
1.4 Power Wiring
1.5 Grounding and Surge Suppression
1.6 Wire One 1812 to a Telco Line - Telephone Mode
1.7 Wire One 1812 to the Internet - Telephone Mode
1.8 Wire Multiple 1812s: Telco/Internet - Telephone Mode
1.9 Wire One 1812 - Intercom Mode
1.10 Wire Multiple 1812s - Intercom Mode
1.11 Main Terminal Description
SECTION 2 - PROGRAMMING
2.1 Programming Methods
2.2 Master Code
2.3 System Parameters Programming
Programming from the System Keypad
Programming from a Touch-Tone Telephone
Quick Reference Table
2.3.1 Phone Mode or Intercom Mode
2.3.2 System Set-Up Code
2.3.3 Talk Time
2.3.4 Relay Strike Time
2.3.5 Tone Open Numbers
2.3.6 Answer Incoming Call on X Rings
2.3.7 Answer Incoming Call - Enable / Disable
2.4 Time Functions
2.4.1 Time and Date Calendar Chip Programming
2.4.2 Do Not Disturb Time Zone Programming
2.4.3 Automatic Relay Activation Time Zones Programming
2.4.4 Access Code Time Zone Programming
2.4.5 Call Forward Time Zone Programming
2.4.6 “Flash ” Access Code Time Zone Programming (One Day Only)
1
1
2
2
3
4
5
8
8
9-10
11
12
13
13
14
15
16
17
18
19
19
19
20
21
21
21
22
23
23
23
24
24
25
25
26
26
26
27
27
28
28
TABLE OF CONTENTS

1812-065-V-12-14 5
TABLE OF CONTENTS
2.5 Programming Dial-Out Functions
2.5.1 Call Forward Phone Number Programming
2.5.2 Call Forward - Enable / Disable
2.5.3 Preprogrammed Phone Numbers “Dial a Phone Number”
2.6 Access Codes to Operate Access Control Devices
2.6.1 Access Code Programming
2.6.2 Delete an Access Code
2.6.3 Delete All Access Codes
SECTION 3 - ADJUSTMENTS
Speaker Volume
Microphone Gain
Interface Board LED Status
System Keypad and Push To Call Button
SECTION 4 - OPERATING INSTRUCTIONS
4.1 Calling the Homeowner’s Phone from the 1812
4.2 Call Waiting
4.3 Preprogrammed Phone Numbers
4.4 Access Codes
Homeowner’s Programming Instructions (From Home Phone or 1812)
4.5 Call Forward - Enable / Disable
4.6 Call Forward Time Zone - Enable / Disable
4.7 Do Not Disturb - Enable / Disable
4.8 Access Code Time Zone - Enable / Disable
4.9 Auto Relay Activation Time Zones - Enable / Disable
4.10 Answer Incoming Call - Enable / Disable Only from Phone
4.11 Relay Activation Check
4.12 Remote Programming
4.13 Remote Relay Activation
4.14 Switch Input Operation (Terminals 6, 7, 8 & 9)
SECTION 5 - MAINTENANCE
5.1 Troubleshooting
5.2 1812 Classic Wiring Schematic
5.3 Phone Line Polarity
5.4 Isolating Noise Problems
5.5 Troubleshooting Table
5.6 Accessories
5.7 Programmed Information Log Sheets
Master Code, Tone Open Numbers. Do Not Disturb, Call Forward, Access Codes and Automatic Relay Activation time zones.
Preprogrammed Phone Numbers. Access Code Log Sheet (01-25 Location Codes for Relay 1, 26-50 Location Codes for Relay 2).
29
29
29
29
30
30
30
30
31
31
31
31
31
32
32
32
32
33
33
34
34
34
34
34
35
35
35
35
36
36
36
37
38
38-39
40
41-42

1812-065-V-12-14
6
FCC – United States
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC
Rules and Regulations. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communica-
tions. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
FCC Registration Number: DUF6VT-12874-OT-T
DOC - Canada
The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment
meets certain telecommunications network protective, operational, and safety requirements. The Department does not guaran-
tee the equipment will operate to the users satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecom-
munications company. The equipment must also be installed using an acceptable means of connection. The customer should be
aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any
repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure, for their own protection, that the electrical ground connections of the power utility, telephone lines, and
internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural
areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspec-
tion authority, or electrician, as appropriate.
DOC Registration Number: 1736 4507 A
Notice:
The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone
loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices
subject only to the requirement that the sum of the load numbers of all the devices does not exceed 100.
Notice:
DoorKing does not provide a power transformer on units sold into Canada. Use only transformers that are CSA listed to power
the telephone entry system. The model 1812 Classic requires a 24-volt, 20 VA transformer.
Listing:
This product has been tested to and found to be in compliance with the U.L 294 Safety Standard by Intertek Testing Services NA
Inc. (a Nationally Recognized Testing Laboratory) and is ETL listed.
Important Notices

1812-065-V-12-14 7
1. If the clear floor space allows only forward approach to the system, the maximum high forward reach allowed is
48inches above grade to the top of the keypad.
2. If the high forward reach to the system is over an obstruction of greater than 20 inches but less than 25 inches,
the maximum high forward reach allowed is 44 inches above grade to the top of the keypad.
3. If the clear floor space allows parallel approach by a person in a wheelchair, the maximum high side reach shall
be 54 inches above grade to the top of the keypad.
4. If the high side reach is over an obstruction of 24 inches or less, the maximum high side reach allowed is 46
inches above grade to the top of the keypad.
•Prior to beginning the installation of the telephone entry system, we suggest that you become familiar with the
instructions, illustrations, and wiring guidelines in this manual. This will help insure that you installation is performed in
an efficient and professional manner.
•The proper installation of the telephone entry panel is an extremely important and integral part of the overall access
control system. Check all local building ordinances and building codes prior to installing this system. Be sure your
installation is in compliance with local codes.
•When used to control a door or pedestrian gate, try to locate the telephone entry system as near as possible to the entry
point. The unit should be mounted on a rigid wall to prevent excessive shock and vibration from closing doors or gates.
Continuous vibration and shock from slamming doors or spring-loaded pedestrian gates will damage the circuit board.
Under no circumstances should the unit be mounted directly to a moving door or gate.
• ADA mounting requirements for door control. The requirements below apply only when the telephone entry system is
being used to control entry through a public door only. If this system is used to control entry through a vehicular gate or
private entrance, the dimensions noted below do not apply.
General Information
•When used to control a vehicular gate with an automatic gate operator, the telephone entry system must be
mounted a minimum of ten (10) feet away from the gate and gate operator, or in such a way that a person cannot
operate the entry system and/or touch the gate or gate operator at the same time.
•Be sure that the system is installed so that it is not directly in the traffic lane. Goose neck mounting post and kiosks
work well for these type systems. When planning where to locate the system, take into consideration traffic lane layouts,
turn around lanes for rejected access, conduit runs, power availability, etc.
•Environmental factors must also be taken into account. Surface mount units are designed for direct outdoor
installations, however it is preferable to protect them from direct exposure to driven rain or snow whenever possible.
Flush mount units must be protected from direct exposure to the elements.
•This telephone entry system contains a number of static sensitive components that can be damaged or destroyed by
static discharges during installation or use. Discharge any static prior to removing the circuit board from the lobby panel
by touching a proper ground device.
•Instruct the end user to read and follow these instructions. Instruct the end user to never let children play with or
operate any access control device. This Owner’s Manual is the property of the end user and must be left with them
when installation is complete.

1812-065-V-12-14
8
SECTION 1 - INSTALLATION
Installation of the 1812 Classic Telephone Entry System involves the installation of the hardware, by-pass board, and the wiring
of these components. Be sure that all dirt, metal or wood debris is removed from inside after mounting it. Any debris inside
could damage the control board and cause the 1812 Classic system to malfunction during operation.
Use the specification dimensions on pages 2 and 3 to help with the installation of your chosen 1812 Classic model.
When the 1812 Classic is used to control a vehicular gate with an automatic gate operator, it must be
mounted a minimum of ten (10) feet away from the gate and gate operator, or in such a way that a person
cannot operate the 1812 Classic system and/or touch the gate or gate operator at the same time.
1.1 Mount the 1812 Classic
The control board removal is the same for all models.
1. Unlock and open the 1812 door.
2. Disconnect the keypad plug and
door accessories plug from the
control board.
3. Remove the 4 screws.
Carefully remove control board.
Keep the control board in a protected
area during the mounting installation.
CAUTION The control board contains static sensitive
components. Discharge any static electricity from
your hands by touching a proper ground device
before removing the control board.
Remove the Control Board
WARNING
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1