DLX X Series User manual
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05 PROUDLY MADE IN THE USA. // CAGE CODE: 7CFK2 // DUNS #: 079751064 // SBA 8(a) CERTIFIED
ENGLISH MANUAL
//
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05
//
TITLE HERE TITLE HERE
1 1
// LIMITED WARRANTY //
At Deployed Logix we’re redefining rapid deployment. Through our extensive
work with law enforcement, search and rescue teams, various first responders,
private organizations both domestically and abroad, and the military, our team
understands that when a crisis calls, seconds count. Discover why we are the
leader in American-made, rapidly deployable disaster preparedness products.
Your Deployed Logix handmade quality products are covered by a three-year
limited warranty. The limited warranty does not cover small imperfections due,
in part, to the production of handmade products. Any imperfections must be
limited and not inhibit the performance of the product. The limited warranty
is restricted to the repair or replacement of any part which proves to be
defective, at the discretion of Deployed Logix, and the claim must be made
in writing prior to the warranty’s expiration date. Deployed Logix will repair or
replace any component deemed to be faulty from manufacturing in the most
efficient and timely means available.
The limited warranty on workmanship is limited to defects at the time
of manufacturing and does not cover general wear, tear, or misuse of the
product. The warranty does not cover damage caused by abuse, misuse,
neglect, or improper care by the end user in the application of the Deployed
Logix product.
The products and/or components not manufactured by Deployed Logix
shall be subject only to the warranty extended by the original manufacturer.
Component manufacturer warranties may exceed that of Deployed Logix. No
warranty is made or implied regarding the intended use of the product.
Deployed Logix must authorize all claims prior to any action taken by the
end user. No items shall be returned for warranty repair without prior written
authorization from Deployed Logix. For replacement of products damaged
from general use and time please contact Deployed Logix in reference to the
“Buy Back Program.”
For immediate attention regarding any defective product, please phone
Customer Support at +1-541-357-5978, 8:00 AM – 5:00 PM, USA Pacific Time.
*This warranty does not cover marks, scuffs, or abrasions that might allow
light to pass through the blackout vinyl.
X-SERIES MODEL SPECIFIC SHELTER COMPONENTS
PURLIN BAR
CENTER ARCH ASSEMBLYLEG ASSEMBLY
CENTER ARCH ASSEMBLY
LEG ASSEMBLY
CABLE SUPPORT
X-16 = 1
X-24 = 2
X-32 = 3
X-40 = 4
HEADER BAR
A
B
X-SERIES STANDARD SHELTER COMPONENTS
1
//
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05 2
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
SPRAYER ADJUSTMENT
!
X-SERIES COMPONENT BAGS
X-Series Shelter Component Bags
Side Connect Frame
Components
Side Connect
Doorway Components
Standard Frame
Components
Model Specific
Components
X-Series Shelter Component Bags
Side Connect Frame
Components
Side Connect
Doorway Components
Standard Frame
Components
Model Specific
Components
X-Series Shelter Component Bags
Side Connect Frame
Components
Side Connect
Doorway Components
Standard Frame
Components
Model Specific
Components
X-Series Shelter Component Bags
Side Connect Frame
Components
Side Connect
Doorway Components
Standard Frame
Components
Model Specific
Components
X-Series Shelter Component Bags
Side Connect Frame
Components
Side Connect
Doorway Components
Standard Frame
Components
Model Specific
Components
X-Series Shelter Component Bags
Side Connect Frame
Components
Side Connect
Doorway Components
Standard Frame
Components
Model Specific
Components
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05
//
3
1
8 ft
8 ft
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
SPRAYER ADJUSTMENT
UNPACKING ARCH SETUP
1 2
Before construction, determine your desired structure location. Clear the
area of any debris that could damage the shelter or create a hazard for
personnel. Lay out the frame wraps labeled “A” and “B” in the selected
location with the “A” frame wrap at the beginning of the run.
Retrieve the center arch assembly from frame wrap “A”. Swing joint and
secure with outside pins as shown in diagram. Be sure to orient all pins
toward the interior of shelter throughout setup to prevent pin extraction.
//
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05 4
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
SPRAYER ADJUSTMENT
ARCH SETUP ARCH SETUP
3 4
Take out the two (2) leg assembly sections from frame wrap “A” and place
them on the ground with feet facing upwards. Swing up the armature.
Connect leg assembly to center arch assembly. Pin in place with pin
oriented to interior of shelter. Repeat step for each X-Series frame wrap.
Complete the previous steps for all the center arch assemblies and leg
assemblies included in frame wrap “B”. Once complete, arrange arch
sections parallel to each other with 8 ft (2.44 m) of space between each.
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05
//
5
5
PURLIN BAR PURLIN ARMS
PURLIN x 5
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
SPRAYER ADJUSTMENT
PURLIN SETUP PURLIN SETUP
5 6
Retrieve five (5) purlin bars from each “B” frame wrap. Swing out arms
and place in corresponding locations. These bars will connect your arch
assemblies to each other.
Secure purlin bars by inserting into both sockets and turning 90°. Next,
secure purlin arms by inserting lug into corresponding socket, turn 90° and
lower lever to lock. For easy assembly, work from one end of shelter to the
other. Repeat until each frame section has been properly secured.
//
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05 6
7
ENDWALL ARCH SECTIONS
x2
6
ROOF PEAK PURLINS
MUST ALTERNATE DIRECTION
TOP-DOWN VIEW
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
SPRAYER ADJUSTMENT
ARCH CONNECTION HEADER BARS
7 8
WARNING! Roof peak support bars must alternate in orientation for
proper installation. Refer to the the above diagram for layout and number
of sections needed for each shelter construction.
Retrieve two (2) header bar sets from the “A” frame wrap. Connect each
header bar set and pin in place at each open arch section as shown. Note
direction of bar and pin orientation when installing.
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05
//
7
OUTSIDE
POSTS
INSIDE
POSTS
8
INTERIOR ARCH SECTIONS
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
SPRAYER ADJUSTMENT
TENSION CABLES ROOF COVER INSTALLATION
910
Retrieve tension cables from frame wrap “A”. Connect one set of tension
cables for each interior arch segment. Once secured in the correct slot, pin in
place. If the cable appears to be too short, lift at the peak of the arch section
to release tension and close the distance between the slots.
Place folded roof cover along peak of frame. Locate grommets and
slide on to provided posts along roof ridgeline. Once secured along the
ridgeline, unfold the roof cover towards the eave of the shelter. The outer
posts will have locking clips while the interior sections do not.
//
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05 8
ENDWALL
SIDEWALL
*Some X-Series model generations will have differing
configurations of endwall securing straps.
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
SPRAYER ADJUSTMENT
ENDWALL INSTALLATION SIDEWALL INSTALLATION
11 12
Unfold the endwall and place it near the open ends of the shelter frame.
Lift up the roof cover enough to hook the grommet strap of the endwall
onto the center post at the peak of the shelter roof gable. If you plan to
connect additional shelters do not connect the grommeted strap.
Lay out folded sidewall section along the shelter frame. Align grommets
with posts along the shelter’s eave. Slide posts through corresponding
grommets. Once the sidewall is attached, locate grommets on roof section
and slide on to posts. Connect hook & loop strips. Use pin to secure.
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05
//
9
13
*Endwall hidden for greater clarity.
12
KEEP HANDS CLEAR
OF MOVING PARTS
DURING LIFTING!
*Endwall hidden for greater clarity.
RAISE ONE
SIDE ONLY!
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
SPRAYER ADJUSTMENT
RAISING THE SHELTER INSULATION INSTALLATION
13 14
USE CAUTION. Gather recommended personnel. Clear area of any debris
and make sure shelter material is not caught on itself or other environmental
hazards. Check that the retaining pin is not connected. In unison, lift up at
each eave joint, pulling the leg inwards. Pin in place to secure.
With the shelter in the kneeling position, connect the center line of the
insulation to the header bars and tension cables of the shelter. This will
be a combination of hook & loop straps and clips depending on your
generation of shelter.
CAUTION!
//
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05 10
15
KEEP HANDS CLEAR
OF MOVING PARTS
DURING LIFTING!
*Endwall hidden for greater clarity.
*Endwall hidden for greater clarity.
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
INSULATION INSTALLATION RAISING THE SHELTER
15 16
Work outward from the center line and connect the insulation liner to the
shelter frame using the clips and D-rings.
USE CAUTION. Check that the retaining pin is not connected.With the
shelter in the kneeling position and insulation partially installed, raise the
other side of the shelter by repeating STEP 13.
CAUTION!
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05
//
11
17
16
*Endwall hidden for greater clarity.
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
INSULATION INSTALLATION INSULATION INSTALLATION
17 18
After lifting the shelter, continue to attach the insulation liner to the
shelter frame along the eave of the shelter. These connections will be a
combination of hook & loop straps and clips.
Swing the sidewall portion of the insulation liner towards the outer frame
sections and secure with hook & loop straps.
//
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05 12
19
18
ATTACH INSULATION ENDWALL.
BEGIN AT TOP CENTER AND
WORK OUTWARDS TOWARDS
SIDE WALLS.
*Endwall hidden for greater clarity.
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
INSULATION INSTALLATION SIDEWALL / ENDWALL CONNECTION
19 20
With the insulation liner installed, attach the insulation endwalls. If you will
be connecting additional shelters to this unit, you may choose to connect
with a X-Series Connector instead of insulation endwall.
Unroll the sidewall sections if they did not come down during the lifting
process. Secure the remaining segments of hook & loop strips to complete
the installation of the shelter endwalls.
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05
//
13
21
SIDEWALL TO FLOOR ATTACHMENT
SIDEWALL TO FRAME ATTACHMENT
*Covers hidden for greater clarity.
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
FLOOR INSTALLATION FLOOR / SIDEWALL ATTACHMENT
21 22
Lay out the floor on the interior of the shelter, closest to one sidewall.
Unfold from one side to the other. It’s okay to have a little slack in the
floor. This will resolve during the connection process.
Attach the sidewall to the lower purlin bar. Loop down and around the bar, up
through both D-rings on the sidewall, then pull down through the bottom D-ring
to sinch tight. Attach the floor in the same way, but thread the strap through the
D-ring on the floor before threading through the D-rings on the sidewall.
//
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05 14
*Endwall hidden for greater clarity.
FLOOR CORNER
FLOOR CORNER
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
FLOOR INSTALLATION
23 24
Push excess flooring material into the corner and tie strap around the
corner frame. Fold and tuck the flooring in on itself to create a berm in the
corners of the shelter. Connect buckle and tighten.
With the shelter floor in place and attached to the sidewalls and endwalls,
connect the insulation liner to the facing hook & loop strip that runs along
the entire perimeter of the shelter. For best results start at a known point
like the door or corner and work out from one end to the other.
FLOOR / INSULATION CONNECTION
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05
//
15
NOTE: It is helpful to fold and stow shelter
components as you dismantle them. Utilize
the shelter floor as a clean surface to fold
and organize parts and keep them clear of
debris, dust, water, or mud.
STAKE & SECURE
~4FT
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
SPRAYER ADJUSTMENT
STAKING THE SHELTER SHELTER TAKEDOWN
25 !
WARNING: SHELTER MUST BE STAKED & SECURED AT ALL TIMES
WHEN ERECTED. FAILURE TO SECURE STRUCTURE COULD RESULT
IN DAMAGE TO EQUIPMENT OR SERIOUS PERSONAL INJURY!
Begin strike of shelter by removing all installed accessories and anchor
systems. Disconnect all power sources and climate control systems.
Leave floor in place for clean folding of components.
//
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05 16
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
ENDWALL REMOVAL INSULATION ENDWALL FOLDING
1 2
Begin takedown by closing and securing all windows and doors on both
the insulation and outer cover. Disconnect insulation endwalls from the
insulation liner. Clean and then fold according to folding diagrams.
Lay endwall with interior facing up. Fold in corners along door zippers.
Fold back excess. Fold section along long edge evenly toward the center.
Repeat on other long edge. Fold end over end with ~ 21 inch folds.
INTERIOR FACE UP
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05
//
17
PARTIALLY REMOVE ENDWALL
ROLL UP SIDEWALL ONTO ROOF
UNDO STRAPS
SIDEWALL TO FLOOR ATTACHMENT
SIDEWALL TO FRAME ATTACHMENT
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
FLOOR REMOVAL DISCONNECT SIDEWALL / ENDWALL
3 4
Detach flooring from the shelter. Undo all straps that connect the floor and
the sidewall to the shelter frame. Work around the shelter until the entire
perimeter is detached from the frame.
Detach the endwall from the sidewall on all four (4) sides. Remove past
the eave joint so that the endwall hangs clear from the pinch point on the
roofline. Roll up the sidewall and toss on top of the roof on both sides. This
will give you adequate space to grip the frame during the lowering process.
//
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05 18
KEEP HANDS CLEAR
OF MOVING PARTS
DURING LOWERING!
5
LOWER ONE
LOWER ONE
SIDE ONLY!
SIDE ONLY!
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
DISCONNECT INSULATION LOWERING THE SHELTER
5 6
Disconnect the sidewall portion of the insulation liner from outer frame
sections on both sides. Then disconnect the insulation clips attached at
the eave of the shelter.
Gather appropriate personnel. Release all pins from joints on one side of the
shelter. Pull the leg inward to relieve tension on the joint and allow the pin to pull
free. In unison, pull the leg section outward while lowering joints to the ground.
Keep the frame even as you lower to prevent stress on the joints.
//
//
//
© 2021 DLX ENTERPRISES LLC. // VERSION 1.05
//
19
ENDWALL
REMOVE & FOLD ENDWALL
DRAIN INSTALLATION DRAIN PUMP INSTALLATION
ENDWALL REMOVAL ENDWALL FOLDING
7 8
With the shelter partially lowered, lift up the roof cover and detach the
endwall strap. Remove the endwall entirely. Clean and fold prior to
stowing.
Lay endwall with interior facing up. Fold in corners along door zippers.
Fold back excess. Fold section along long edge evenly toward the center.
Repeat on other long edge. Fold end over end with ~ 21 inch folds.
EXTERIOR FACE UP
Other DLX Shelter manuals
