DM TECH D9000A SR User manual

ISO 9001:2015 Certified Company
№ 34, етаж 5,
Тел./факс: [phone]
e-mail :[email protected]
web : www.dm-teh.com
Адрес : гр. Плевен 5800
ул.”Николай Хайтов”№16
Instruction manual
D9000A-SR
Addressable Optical smoke detector
Тип
Характеристики
Чувствителност/Клас
D9000AI SR
Addressable Optical smoke detector with built isolator
EN 54-7
D9000A SR
Addressable Optical smoke detector
EN 54-7
1. D9000A SR is an addressable optical smoke fire detector, designed for use in addressable fire alarm systems that support the
DMTech communication protocol. The detector is powered by the panel and can be controlled via the communication protocol. The
D9000A SR fire detector is compatible with the B9000A base
Technical data
•DMTech protocol
•Certified according EN 54-5, EN 54-7 and EN 54-17
•LED indication 360° visibility
•Built-in isolator - model D9000AI-A1R/A1S
•Supply voltage from panel FP9000А 18-30VDC
•Consumption
- current consumption in Duty mode < 500μA/28VDC
- current consumption in, with communication 2.0mA
•Maximum current in alarm mode - RI terminal 2.0 mA
•Connecting wires 0.5mm² - 2.0mm²
•Operating temperature -10°C до +65°C
•Resistance to relative humidity (93 ± 3)% при
40°C
•Degree of protection IP40
•Joining with base B9000A
•Weight (with base) ~100g
•Sizes (with base) Ø100x52mm
•Material (plastic) - ABS
Mounting of the detector
- select the location (according to the project drawings) for mounting the detector;
- Install the base with suitable dowels and screws.
- connect the electrical cables according to the attached diagram (Fig. 1);
фиг.1
- place the detector on the base and turn clockwise until the benchmarks match;
- If you want to lock the detector:
- Remove the key from the base beforehand (fig. 2).

Паспорт на пожароизвестители серия D9000A-SR
- Break the plastic at the indicated location at the bottom of the sensor (Fig. 3).
Fig.2 Fig.3 Fig.4
- Place the detector on the base and rotate it.
- If the detector is locked to the base to unlock, insert the key to stop the specified place (Figure 4) and rotate the detector in the
direction counterclockwise;
- Perform a detector test to check the correct operation of the light indication;
- In normal operation, the LEDs will flash for 16 seconds.
Testing and support
Testing
–apply the supply voltage to the circuit;
–wait about a minute or until the detector flashes;
–Follow the procedure for addressing the detector from the instruction panel on the fire panel.
–In working condition, activate the detector with a temperature probe and / or a probe with a test spray. The two red LEDs must
always be lit..
Service support
➢external inspection for mechanical damages and dirt - once a year;
➢verification of performance - one a year;
➢prophylactic cleaning - depending on the environment.
Warranty
➢The manufacturer guarantees that the product complies with EN 54-5 and EN54-7.
➢The warranty period is 36 months from the date of sale, provided that:
➢- storage and transport conditions are met;
➢- the commissioning is carried out by authorized persons;
➢- the operating requirements set out in this manual are observed.
➢- the defects are not caused by natural phenomena and failures of the power supply network.
➢If a warranty repair is required, please contact us by telephone or e-mail to provide you with instructions on how to
perform your warranty obligations. The repairs are carried out at the company's service center.
Tel.: [phone]
e-mail: [email protected]
DMTech wishes you pleasant work!
2.