DMP Electronics EBOX-58 Series User manual

EBOX-58SeriesMiniPC
User’s Guide

EBOX-58 Series User Manual
DMP Electronics Inc. 2
Copyright
The information in this manual is subject to change without notice for continuous improvement.
All rights are reserved. Manufacturer assumes no responsibility for any inaccuracies that may contain
in this document, and makes no commitment to update or to keep current information.
No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part,
in any form or by any means without the prior written permission of the DMP Electronics Inc.
Copyright 2021 DMP Electronics Inc.
Trademarks Acknowledgment
Intel® Braswell E8000 & N3160 is the registered trademark of Intel Corporation.
is the registered trademarks of DMP Electronics Inc.
Other brand names, product names or trade names appearing in this document are the properties
and registered trademarks of their respective owners. All names mentioned herewith are served
for identification purpose only.
Safety Information
WARNING
Do not expose EBOX torain or moisture, in orderto prevent shockand fire hazard.
Never install EBOX in wet locations.
Do not open cabinet to avoid electrical shock. Refer to the nearest dealer for qualified personnel servicing.
Never touch un-insulated terminals or wireunless power adaptor and display monitor are disconnected.
Locate EBOX as close as possible to the socket outline for easy access and to avoid force caused by
entanglingof your arms with surrounding cables from the EBOX.
When using EBOX, avoid using or installing the modem to the serial port during a storm or a lightning.
Do not use the modem or a telephone to report a gas leak in the vicinity of the leak.
USB connectors are supplied with Limited Power Sources.
DO NOT ATTEMPT TO OPEN OR TO DISASSEMBLE THE CHASSIS (ENCASING)
OF THIS PRODUCT. PLEASE CONTACT YOUR NEAREST DEALER
FOR SERVICING FROM QUALIFIED TECHNICIAN.

EBOX-58 Series User Manual
DMP Electronics Inc. 3
Regulatory
FCC Class A Note
This equipmenthas beentested and found to comply with the limits for a Class Adigital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated ina commercial environment. This equipment generates,uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interferencein which case user will be required to correct interference at his own expense.
Testingwas done with shielded cables. Follow FCC regulations, user must use shielded cables with installation.
WARNING
This product complies with EN55032 class A. In adomestic environment, it may cause radio interference
in which case theuser may be required totake adequate measures.
Changes or modificationsto this unit not expressly approved by the party responsible for compliance could void
user’s authority to operate the equipment.
This device complieswith Part15 ofthe FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2)this device must accept any interference received,
includinginterference that may cause undesired operation.
This digitalapparatus does not exceed Class A limits for radio noise emissions from digital apparatus as set out in
interference - causing equipment standard “Digital Apparatus”, ICES-003of theDepartment ofCommunications.
Manufacturer’s Declaration of Conformity
This equipment has been tested and foundto comply with the requirementsof European Community Council
Directives2014/30/EU & 2014/35/EU relatingto electromagnetic compatibility and product safety respectively.
Attention
This product hasbeen designed and certified to comply with certain regulatory requirementspertaining to
Information Technology Equipment. This product has not been designed for use as a medicaldevice.
Withoutlimitation ofthe foregoing,this productisnot intendedand hasnot beencertified foruse in ahospital
or clinical environment to diagnose, treat, or monitor patients under medical supervision, it is not intended
and has not been certified to make physical or electrical contact with patients,norto transfer energy to
or from patients and/or todetect such energy transfer toor from patients.

EBOX-58 Series User Manual
DMP Electronics Inc. 4
Purchase Agreement
Purpose:
In accordance to the general commercial conduct of Trust and Fair Trade, herewith below isthe agreement
for the protection for both parties, DMP and Users in pursuant of trading.
Product Description:
EBOX-58 Series industrial fanless PC integrates an Intel® BraswellE8000 or N3160 series processor.
Supports memoryup to 8GB DDR3L, Dual Giga LAN, Dual RS-485/RS-232 upto4 ports,etc.Suitableplatform
for IoT, M2M, Industry 4.0, Home Automation Security, Point-of-sales,Publictransportation andmany more.
Distribution Convention:
1. This ProductincludesaPCand a powersupply unit.Upon receivingthis product,pleasereferto usermanual
to check for the contentsand appearance of this product; contact the nearestdealer or DMP office for any
defectiveor missing parts immediately. The supplier will not be responsible for any reported discrepancy
there after the expiration period of 3-days from the receiveddate.
2. In consideration of transportation and the costof storage, the supplier provides tothe distributors
a warranty of 12 months.This warranty covers the failure caused by hardware breakdown.
(excluding hard drives), butdoes not cover the actof misuseand mishandling.
3. The supplier will not accept unknown post, therefore ifyou wish to repair or to return your goods,
please contact your nearest dealer to make your declaration, at the same time, apply for anRMA number
(RMA stands for Return Merchandise Authorization), and ask for RMA form then fill-up for authorization.
4. The freight for return goods for repair will follow the International customarypractice and convention.
Both parties is to payfor freight of one shipment each.The shipper is required to prepay the freight from
the place of origin (This means that the returnee/user covers thefreight for return goods, while the Supplier
covers the freight for goods after the repair).
5. Obsolete warranty is referred to as: (1)Expiration of warranty or (2)Damage due to misuse within warranty.
The Supplier will betakeninto consideration of the circumstances, to provide repair service with charges
expensefor obsolete warranty.This expense includes the cost ofmaterial and the cost of labor.
Note: If there is other particularissue, not listed in the above conditions, both parties agreed to follow
GeneralLawof Commerce with fair and reasonable discussion in handling and resolvingtheargument.

EBOX-58 Series User Manual
DMP Electronics Inc. 5
Contents
Chapter1
07 UnpackingEBOX MiniPC
Chapter2
10 EB-58 Seriesno COMportsmodel types
11 EB-58 Series COMportsmodeltypes
12 EB-58 Internal description
13 Appearance Diagram
14 SystemSpecifications
Chapter3
16 BIOS Reconfiguring
16 Hot Key
17 UEFI PXE diskless boot setting
18 Legacy PXE diskless boot setting
19 Drivers Installation Guide
19 Chipset driver
20 Graphic driver
21 Audio driver
22 LAN driver
23 TXE driver
Chapter4
25 Onboard Connectors Summary
25 Pin Assignments
Chapter5
29 Taking Care ofEBOX
30 Troubleshooting
Chapter6
33 Termsand Condition
33 Warranty
33 Serviceand Support
33 Return Merchandise Authorization (RMA) Policy
33 ShippingPolicy

EBOX-58 Series User Manual
DMP Electronics Inc. 6
Chapter1

EBOX-58 Series User Manual
DMP Electronics Inc. 7
Unpacking EBOX Mini PC
Component List:
Item No.
Description
Quantity
1
EBOX-58 SeriesMiniPC
x1
2
Power Adaptor40W; Vin:100~240V AC 50~60Hz
x1
3
Power cable ( available US, UK, EU, AUtypes )
x1
4
VESA screw
x4
5
SATA SLIM 7+15 pin cable
x1
Note: The accessories are subject to change without immediate notice.
Check before Use
1. EBOX-58 Series Unit 2.Power adapter40W
3. Power cable 4. VESA screws
5. SATA SLIM cable

EBOX-58 Series User Manual
DMP Electronics Inc. 8
Preface
EBOX-58 Series Mini PC
EBOX-58 Series industrial fanless PC integrates an Intel® Braswell E8000 or N3160 series processor.
Supports memoryup to 8GB DDR3L, Dual Giga LAN, Dual RS-485/RS-232up to4 ports,etc.Suitable platform
for IoT, M2M, Industry 4.0, Home Automation Security, Point-of-sales,Publictransportationand manymore.
EBOX-58Seriescan beattached to any VESA mountingfixture; allowing ittobe securely mounted onto desks,
walls, or buildings, and thereby optimizes your work area. It canalso attach directly to any size LCD monitor,
for the use at trade shows,presentations, promotions, etc. With FANLESS design, it’s ideal to be used
in the environment where temperaturedemand is critical.
EBOX-58 Series supports Win 10, Win10 IoT,Win 7, WES7, Linux Ubuntu and Debian to meet ready-to-market
demand and provide competitive advantages for customers.

EBOX-58 Series User Manual
DMP Electronics Inc. 9
Chapter2

EBOX-58 Series User Manual
DMP Electronics Inc. 10
EBOX-58 Series no COM ports model types:
A
Front Panel
A: Power LED
Green flashing LED indicates SATA storage activity
B: SATA LED
LED lights up when the system is turned on
C: Power Button
System power on/off
D: USB 3.0 ports
External USB devices use
E: Line Out
Audio output
F: Mic In
Microphone input
G: Micro SD Card Slot
Expanded storage Micro SD use
Back Panel
H: RJ-45 LAN Jack
Realtek 8111H GigaLAN
I: HDMI Output port
HDMI display output
J: Power Jack
Volt: DC +8V~+26V
A
B
B
C
D
D
D
D
D
D
E
F
E
F
G
G
H
H
H
I
I
J
J

EBOX-58 Series User Manual
DMP Electronics Inc. 11
EBOX-58 Series COM ports model types:
*Model types with Auto Power On
features do not have reset button.
Front Panel
A: Power LED
Green flashing LED indicates SATA storage activity
B: SATA LED
LED lights up when the system is turned on
C: Power Button
System power on/off
D: USB 3.0 ports
External USB devices
E: Line Out
Audio output
F: Mic In
Microphone input
G: Micro SD Card Slot
Expanded storage Micro SD use
H: COM ports
RS-232 x2
Back Panel
I: RJ-45 LAN Jack
Realtek 8111H GigaLAN
J: HDMI Output port
HDMI display output
K: Power Jack
Volt: DC +8V~+26V
L: COM ports
RS-232 x2 or RS-485 x2
A
A
B
B
C
C
D
D
D
D
D
D
E
F
E
F
G
G
H
H
I
I
I
J
J
K
K
L
L
L
L

EBOX-58 Series User Manual
DMP Electronics Inc. 12
EBOX-58 Internal description
Optional item DGF109A M.2 Wi-Fi/BT module info www.compactpc.com.tw
To use SATA SLIM DOM as a boot drive, connect
SATA SLIM 7+15 pin cable and place SATA SLIM
DOM under the PCB, fixed at the bottom.

EBOX-58 Series User Manual
DMP Electronics Inc. 13
Appearance Diagram

EBOX-58 Series User Manual
DMP Electronics Inc. 14
Order information

EBOX-58 Series User Manual
DMP Electronics Inc. 15
Chapter3

EBOX-58 Series User Manual
DMP Electronics Inc. 16
BIOS Reconfiguring
Load Default Setting
1. To reconfigure the hardware, press <Del> during unit boot up to enter BIOS menu.
2. Move to “Save & Exit”Restore Defaults, press Enter and select YES to execute.
3. After setting, press “F10” key to save and reboot EBOX.
Hot key
Press <F11> during unit boot up, a select menu will appear. Use direction key to select boot device.

EBOX-58 Series User Manual
DMP Electronics Inc. 17
UEFI PXE diskless boot setting
1. Press <Del> during unit boot up to enter BIOS menu.
2. Move to “Advanced” “CSM Configuration”and press Enter.
3. Move to “Network”and select “UEFI”.
4. Move to “Boot”FIXED BOOT ORDER Priorities Boot Option #1select “UEFI Network”.
5. Press “F10”to save and reboot EBOX to activate UEFI PXE diskless boot.

EBOX-58 Series User Manual
DMP Electronics Inc. 18
LEGACY PXE diskless boot setting
1. Press <Del> during unit boot up to enter BIOS menu.
2. Move to “Advanced” “CSM Configuration”and press Enter.
3. Move to “Network”and select “Legacy”.
4. Move to “Boot” “Boot mode select”select “LEGACY”.
5. Move to “Boot”FIXED BOOT ORDER Priorities Boot Option #1 select “Network”.
6. Press “F10” key to save and reboot EBOX to activate LEGACY PXE diskless boot.

EBOX-58 Series User Manual
DMP Electronics Inc. 19
Drivers Installation guide
Under Windows 10, thefollowing driversneedto be installedmanually.
1. Chipset
2. Graphic
3. Audio
4. LAN
5. TXE
Please download above drivers from EBOX website.
Chipset driver: (Intel®Chipset Device Software)
1. Unzip Chipset file, execute SetupChipset.exe, and then click “Next” to continue.
2. A license agreement message will pop out, click Acceptand install.
3. Click Finish to completethesetup process.

EBOX-58 Series User Manual
DMP Electronics Inc. 20
Graphic driver:
1. Unzip Graphic file andexecute igxpin.exe, then click “Next” to continue.
2. A license agreement message will pop out, click Acceptand install.
3. After installed, select “Yes, I want to restart this computer now” and click Finish to reboot.