DMP Electronics SCS-104 User manual

MODEL SCS-104 LINE CARD
Installation Guide
DESCRIPTION
Power
DTR
Line 1
Line 2
Line 3
Line 4
J6
Ethernet Phone
Reset
Load
1 2 3 4
The SCS-104 provides four digital
dialer (DD) lines and a network
connection for communication to
DMP panels. Each card includes one
Ethernet network connection. Each
card also includes a non-shielded
eight-pin modular connector that
supports up to four digital dialer
lines, when connected to a standard
RJ61 jack.
An optional PC software
application, SCS-CTM Check-in
Table Manager, is available to
backup the SCS-104 records of
all supervised network accounts
for up to 32 dierent SCS-104 line
cards. The SCS-CTM program is
compatible with SCS-104 Version
100 or higher. For complete
operation information, refer to the
SCS-CTM User’s Guide (LT-0940).
Contact DMP Customer Service to
purchase a copy of the SCS-CTM
Check-in Table Manager software.
Compatibility
• DMP SCS-1R Network Enabled
Receiver
What is Included?
• One SCS-104 Line Card
• Hardware pack
1INSTALL THE LINE CARD
Install the line card in any one of the rack positions with the card
puller in the up position. Connect the line card cable from the
processor card to the line card with pin 1 up. The line card’s number is
determined by the cable it’s connected to.
CONNECT COMMUNICATION LINES
2Connect network and digital dialer lines to the SCS-104 as
needed.
Network
Connect an Ethernet cable from the line card to the customer’s
network. Maximum line impedance is 100 Ohms. The SCS-104
automatically communicates UDP or TCP and uses 128-bit or 256-
bit AES Encryption with compatible panels.
Note: 256-bit encrypted messages sent to the SCS-1R
receiver from an XR550E Panel with Version 104 or higher
requires SCS-104 Line Cards with Version 102 or higher.
Digital Dialer
Connect a phone line from the line card to the customer’s phone
line. Use a standard 103J voice grade (analog) line. Cables can
be fed through the slot in the receiver back plate. Maximum line
impedance is 100 Ohms. Refer to Figure 2 for pinout.
The SCS-104 is registered with the FCC, registration number
CCKCN03BSCS-104; Ringer Equivalence 0.3B.
SCS-104
Line Card
Line Card
Connector
SCS-150
Network Connection
Rack-Mounting
Holes (4)
SCS-150 Receiver
Processor Card
Figure 1: SCS-104 Line Card Positions in the SCS-1R
OVERVIEW
To complete an SCS-104 Line Card installation, this guide walks you through
these required steps:
1. Install the SCS-104 Line Card.
2. Connect communication lines.

Designed, engineered, and
manufactured in Springfield, MO
using U.S. and global components.
LT-1207 21061
SCS-104
Specifications
NIST AES Algorithm Certificate #1760 128-bit
NIST AES Algorithm Certificate #2599 256-bit
California State Fire Marshal (CSFM)
New York City (FDNY)
Underwriters Laboratory (UL) Listed
ANSI/UL 864 Fire Protective Signaling
ANSI/UL 163 Digital Alarm Communicator
ANSI/UL 1610 Central-station Burglar
ANSI/UL 365 Police Station Connected Burglar
ANSI/UL 1076 Proprietary Burglar
ULC-S559-04 Equipment for Fire Signal Receiving
Centers and Systems
ULC-S545 Standard for Residential Fire Warning
System Control Units
ULC-S304 Standard for Central and Monitoring
Station Burglar Alarm Units
ULC-C1023 Household Burglar Alarm System Units
ULC/ORD-C1076 Standard for Proprietary Burglar Alarm
Units and Systems
INTRUSION • FIRE• ACCESS• NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
800.641.4282 | DMP.com
© 2021
ADDITIONAL INFORMATION
Programming
The SCS-104 is programmed through the SCS-150 Receiver Processor Board with software such as Remote Link™. For
more information see the SCS-1R Installation Guide (LT-1037).
Phone Line Monitor
The SCS-104 monitors incoming phone line voltage. During a loss of phone line voltage, the SCS-104 sends a Phone Line
Trouble message (System Message 153) to the host automation or LCD display.
LED Operation
The SCS-104 provides eight LEDs on the card. The green LED labeled PWR turns on when the power supply on the line
card is working properly. Table 1 describes the LED operation:
LED DESCRIPTION
SOLID FLASHING OFF
POWER Power On N/A Power O
DTR Data Terminal Ready N/A Processor is nearly full
LINE 1 Connected (o hook) Ringing Idle
LINE 2 Connected (o hook) Ringing Idle
LINE 3 Connected (o hook) Ringing Idle
LINE 4 Connected (o hook) Ringing Idle
LINK Indicates a valid Network connection Indicates a valid Network connection No connection
LINK SPEED Connected a 100 Base-T N/A Connected at 10 Base-T
Table 1: LED Operation
SCS-104 Software Update
Updating SCS-104 firmware requires Remote Link Version 1.61 or higher.
1. Remove the SCS-104 Line Card from the SCS-1R Receiver.
2. Connect a Model 399 Programming Cable from the line card PROG header to a computer with Remote Link.
3. Place a shorting clip across the 2 pins of the LOAD header, then reinsert the line card into receiver.
4. Open Remote Link and go to System > Remote Update.
5. In Update File, press the More button, then select the SCS104.RU update file. Select the COM port where the line
card is connected, then select Update.
6. After the update is complete, remove the SCS-104 from the receiver, disconnect the 399 cable, and remove the
shorting clip from the LOAD header. Reinsert the line card to begin normal operation.
R
R
R
T
R
T
T
T
8
7
6
5
4
3
2
1
1234
RJ61
Tip
Tip
Tip
Ring
Tip
Ring
Ring
Ring
4
3
2
1
1
2
3
4
1
2
3
4
5
6
7
8
Pin Pair Wire
White/Brown
White/Green
White/Orange
Blue/White
White/Blue
Orange/White
Green/White
Brown/White
Color
Figure 2: Pinout Diagram with Chart
© 2021