DMP Electronics SR3 Installation guide

INSTALLATION AND PROGRAMMING GUIDE
SR3
Bluetooth and Proximity Reader

CONTENTS
Get Started ..................................................1
Procedure..................................................................... 1
What’s Included......................................................... 1
What You’ll Need ...................................................... 1
Step 1: Install the Reader.........................2
Mount the Reader.................................................... 2
Wire the Reader ....................................................... 3
Attach the Cover...................................................... 5
Step 2: Enroll & Associate the Reader...6
56‑Bit Card Format................................................. 6
Step 3: Purchase Credentials ..................7
Step 4: Assign a Mobile Credential........8
User Training Tips .................................................... 8
Step 5: Bind a Credential to a Device....9
Step 6: Use a Credential ........................ 10
Reduce Notifications (Android)........................10
Reference................................................... 11
Test the Reader.........................................................11
LED Operation ..........................................................11
Troubleshooting ......................................................12
Reset the Reader ....................................................13
Reset to Defaults ................................................13
Factory Reset .......................................................13
Compatibility ............................................................14
Panels and Door Controllers.......................... 14
Access Control Modules.................................. 14
Keypads................................................................. 14
Apps........................................................................ 14
125 kHz Proximity Credentials ...................... 14
Directional Antennas ........................................ 14
Ordering Information ............................................14
Specifications ...........................................................15
Compliance Requirements ..................................15
Wiring and Power ...............................................15
UL 294.....................................................................15
Certifications ............................................................15
Underwriters Laboratory (UL) Listed..........15
FCC Information................................................. 16
Industry Canada Information ........................ 16
FCC/IC RF Exposure Requirements........... 16

SR3 Installation and Programming Guide | Digital Monitoring Products 1
GET STARTED
SR3 Bluetooth and Proximity Readers support Mobile Credentials and 125 kHz proximity credentials. The reader comes
with two mounting options, mullion or single‑gang, and is suitable for indoor or outdoor use. The SR3 uses the Wiegand
reader protocol to communicate with door controllers or access control modules.
Procedure
The installation must follow this procedure:
Step 1 (Technician): Install the reader.
Step 2 (Technician): Enroll and associate the reader with a system in Tech APP.
Step 3 (Administrator): Purchase credentials for a customer in Dealer Admin.
Step 4 (Customer): Assign credentials to a user in Virtual Keypad.
Step 5 (End User): Bind a mobile credential to a user’s device in Virtual Keypad.
Step 6 (End User): Use the credential at the SR3 Bluetooth Reader.
This guide walks you through all 6 steps.
What’s Included
What You’ll Need
▶Drill
▶If mounting with wall anchors, a 5/16” (8.0 mm) drill bit
▶If mounting without wall anchors, a 5/64” (2.0 mm) drill bit
▶#1 Phillips screwdriver
▶#2 Phillips screwdriver
▶Pliers
▶Wire connectors
▶Electrical tape
TOP
One
SR3 Bluetooth
Reader
One
Mullion
Base
Two
Wall
Anchors
Two
Mounting
Screws
(#6 x 1”)
One
Case
Screw
(#4 x 1/2”)
One
Single-Gang
Mounting Plate

SR3 Installation and Programming Guide | Digital Monitoring Products 2
STEP 1: INSTALL THE READER
This section covers the steps required for a technician to physically install the reader including mounting, wiring, and
attaching the cover.
Mount the Reader
WARNING: Do not press and hold the button on the back of the reader. This procedure clears the unit’s memory
and firmware, which renders the device inoperable until it is reconfigured and re‑enrolled.
Never mount the reader directly on a moving surface such as a door or gate. Isolate the reader from repetitive shocks
and potential damage. The reader can be mounted on a wall or any suitable flat surface.
1. Determine the purpose of each wire before removing an existing reader. Use a voltage meter to verify that 12VDC
is supplied by the controller, then disconnect power from the reader’s power source
2. Pull the existing wires through the wall. Use the reader base to mark locations for the mounting holes on the
surface. Do not use the plastic base as a guide when drilling.
3. Move any wires in the drill’s path. Drill holes in the surface no more than 1 inch deep. If using wall anchors, insert
them into the holes you drilled in the mounting surface.
4. Slide the base over the existing wiring. If using the single‑gang bracket, slide the bracket on first, then the reader
base. Ensure the base side marked TOP is mounted up.
5. Use the included #6 screws to secure the mounting base to the surface. Do not overtighten the screws.
Mounting and Base Orientation
Mounting Surface
Wires from
Access Control
Module, Keypad,
or Door Controller
Single-Gang
Bracket
(optional) Mount Base
with Side Marked
TOP Facing Up
Reader
Base
Wall
Anchor
(optional)
Wall
Anchor
(optional)
TOP

SR3 Installation and Programming Guide | Digital Monitoring Products 3
Wire the Reader
Connect the reader wires to the access controller according to the purpose of each controller terminal. Refer
to Table 1 and the examples that follow for details. For wiring and power requirements, refer to “Wiring and Power”.
Caution: Do not cut the braided directional antenna wire. Wrap it around and secure it to the wiring harness for
future use.
WIRE COLOR PURPOSE TYPICAL X1 SERIES
TERMINALS
TYPICAL 734 SERIES
TERMINALS
TYPICAL KEYPAD
WIRES
Red Power (Positive) R1 RED Red
Black Ground (Negative) B1 BLK Black
White Data 1 W1 WHT White
Green Data 0 G1 GRN Green/White
Blue Green LED LC LC None
Orange Beeper* (optional) BC RA None
Purple Red LED (optional) None None None
Yellow Smart Card Present (optional) None None None
Copper, braided ‑ Do not cut Directional Antenna (optional) None ‑ Do Not Cut None ‑ Do Not Cut None ‑ Do Not Cut
* If connected, the orange wire (beeper) mimics keypad beeping.
Table 1: Wire Connections

SR3 Installation and Programming Guide | Digital Monitoring Products 4
Directional Antenna Wire to None
Do Not Cut
RED
PROG
RED
KYPD OUT
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NC
C
NO
GRN
YEL
RED + –
Piezo
LC ASREDWHTGRN BLK Z1 Z2 Z3 Z4+ Z4–RA GND GND
KYPD IN
RED
ON
1 2 3 4 734 Series
Access Control
Module
Yellow to None
Red to RED
White to WHT
Green to GRN Black to BLK
Blue to LC
Orange to RA
Purple to None
*
* Orange connection to RA terminal is optional.
734 Wiring Example
+AC/DC- +BAT- R1 W1 G1 B1 LC BC R2 W2 G2 B2 LC BC DS RX CI G
01 02 12V NC C NO
PWR/BOOT
READER 1
READER 2
RELAY
DATA
FIRE
LOCKDOWN
R
L
Yellow to None
Purple to None
Directional Antenna Wire to None
Do Not Cut
Red to R1 White to W1 Green to G1 Black to B1 Blue to LC Orange to BC
X1 Series
Door Controller
* Orange connection to BC terminal is optional.
*
X1 Wiring Example

SR3 Installation and Programming Guide | Digital Monitoring Products 5
Attach the Cover
1. Hook the reader cover onto the top two base latches.
2. Press the reader down and in to seat the cover bottom on the bottom latch.
3. Use the included #4 case screw to secure the reader cover onto the base. Do not overtighten the screw.
4. Apply power to the reader’s connected power source.
After the reader powers on, the LED remains steady yellow.
Hook Press down
Press in
Insert screw
and tighten
12 3
Installing the Cover

SR3 Installation and Programming Guide | Digital Monitoring Products 6
STEP 2: ENROLL & ASSOCIATE THE READER
A technician on site must associate each reader with a system before mobile credentials can be purchased in Dealer
Admin by an Administrator.
Note: For XR Series panels with 734 Series Access Control Modules, ensure Program 734 Options is turned on and
Card Options is set to Custom in Device Setup before proceeding.
1. Stand at the reader and ensure your device has Bluetooth turned on.
2. Open Tech APP, then find and open the appropriate system.
3. Tap the Bluetooth Readers tile.
4. Tap Add. Name the reader, then tap Create.
5. When prompted, touch your device to the reader. When paired successfully, the reader beeps.
6. In Tech APP, open the reader you added. Use the slider to adjust the Reader Range closer or farther as needed.
Range is 3in to 30ft (7.62 cm to 9.14 m).
7. To update the reader’s firmware, go to Firmware and tap Update. If no new firmware is available, this button is not
displayed.
8. Tap Save.
After being enrolled and associated, the reader’s LED changes from steady yellow to steady white.
If you receive a message that states the 56‑bit card format cannot be added, you must add the format manually in Full
Programming > Device Setup > Card Formats. For more information, refer to “56‑Bit Card Format”.
56‑Bit Card Format
NAME WIEGAND CODE
LENGTH
SITE CODE
POSITION
SITE CODE
LENGTH
USER CODE
POSITION
USER CODE
LENGTH
USER CODE
DIGITS
BLUETOOTHFORMAT 56 1 16 17 34 10
Configuring the Reader in Tech APP

SR3 Installation and Programming Guide | Digital Monitoring Products 7
STEP 3: PURCHASE CREDENTIALS
This section covers how an Administrator purchases credentials for a customer in Dealer Admin. These steps can only be
completed after the SR3 Bluetooth Reader is installed and associated with a customer’s system in Tech APP.
Note: To purchase and issue credentials in Dealer Admin, you must either have an Administrator role or a custom
role with Mobile Credential permissions. For more information, refer to Personnel Roles in Dealer Admin Help.
1. Go to Tools > Mobile Credentials.
2. Go to Purchase Credentials.
3. In Customer, select the customer that you want to purchase credentials for.
4. In Quantity, select the number of credentials you want to purchase for your customer.
5. If needed, enter notes. You can use the Notes/PO field to help you track items like why the credentials were
issued and who requested them.
6. To purchase the credentials, select Purchase Credentials. Notify your customer that you completed their
purchase.
Purchasing Credentials in Dealer Admin