DMP Electronics 1164 Installation guide

INSTALLATION AND PROGRAMMING GUIDE
1164/1164NS
Wireless Smoke Detector

TABLE OF CONTENTS
About the 1164............................... 1
Indicator LEDs....................................................... 1
Optional Tamper................................................... 1
Power Supply ........................................................ 1
Cadence Synchronization ................................ 1
1164 Features .................................2
Program the 1164...........................3
Programmer Menu.............................................. 3
Zone Information ................................................ 3
Zone Number........................................................ 3
Zone Name............................................................ 3
Zone Type .............................................................. 3
Next Zone .............................................................. 4
Wireless Zone....................................................... 4
Serial Number....................................................... 4
Supervision Time................................................. 4
Next Zone .............................................................. 4
Bell Options........................................................... 5
Fire Bell Action .................................................... 5
Select A Location ..........................6
Install the 1164 ...............................7
Mount the Base.................................................... 7
Enable the Tamper Switch (Optional) ........ 8
Install the Battery................................................ 9
Replace the cover ............................................. 10
Test the 1164.................................. 11
Clean the 1164...............................12
Mounting Guidelines ................... 14
General Guidelines..............................................14
Authority Having Jurisdiction........................ 15
Locations to Avoid ............................................. 16
Commercial .......................................................... 17
Multi-Family........................................................... 17

Additional Information ............... 18
Supervision Message......................................... 18
Test/Silence Button............................................ 18
Smoke Testing...................................................... 19
Inspection Testing and Maintenance........... 19
NFPA 72 Guidelines........................................... 20
Compliance Specifications ........24
Accessories................................... 25
Backboxes............................................................. 25
Proximity Readers ............................................. 25
Proximity Credentials ....................................... 25
Certifications................................ 26
FCC Information .......................... 27
Industry Canada Information..... 28

1164/1164NS Installation and Programming Guide 1
ABOUT THE 1164
1164/1164NS Wireless Smoke Detectors are 3.0V battery powered, wireless, low-profile,
photo-electric smoke detectors used with 1100 Series DMP Wireless Receivers. The
1164 synchronizes its Temporal 3-alarm cadence with other 1164s installed on the same
fire system. The 1164NS has the same functionality as the 1164, except the 1164NS does
not have a built-in sounder. The 1164NS is intended for use in installations with existing
notification devices.
INDICATOR LEDS
The 1164/1164NS provides two indicator
LEDs. Depending on how the LED is
operating, the red LED indicates there
is either smoke detected, a test alarm in
progress, low battery, or maintenance is
needed.
POWER SUPPLY
The 1164/1164NS is powered by one 3.0V
lithium battery. (Panasonic Model CR123A
or DMP Model CR123-FIRE). Typical
battery life expectancy for the 1164/1164NS
is at least one year.
OPTIONAL TAMPER
The 1164/1164NS features a tamper switch
to send a trouble message to the panel
if the detector is removed from the
mounting base.
CADENCE SYNCHRONIZATION
The Model 1164 only provides a cadence
synchronization with other 1164s on the
system. This option can be enabled in
device programming.

1164/1164NS Series Installation and Programming Guide2
1164 FEATURES
Cover Latch
Test Button
Figure 1: 1164 Features
Red LED
Green LED
Cover
Base

1164/1164NS Installation and Programming Guide 3
PROGRAM THE 1164
When programming an 1164/1164NS smoke detector, refer to the appropriate panel
programming guide, as needed.
PROGRAMMER MENU
Enter 6653 (PROG) at the keypad to enter the PROGRAMMER
menu.
ZONE INFORMATION
Press CMD until ZONE INFORMATION displays. Press a select
key or area to enter the menu.
ZONE NUMBER
Enter the ZONE NO:.
ZONE NAME
Enter the ZONE NAME.
ZONE TYPE
Select FI (fire) as the ZONE TYPE.
PROGRAMMER
ZONE INFORMATION
ZONE NO:
ZONE NAME:
ZONE TYPE
FI EM PN

1164/1164NS Series Installation and Programming Guide4
NEXT ZONE
At the NEXT ZONE? prompt, select NO.
WIRELESS ZONE
At the WIRELESS ZONE? prompt, select YES.
Note: If you are programming the smoke detector onto
a zone that can be either hardwired or wireless, then
this prompt appears. If the zone you are programming is
wireless-only, then the prompt does not appear.
SERIAL NUMBER
Enter the eight-digit SERIAL NO found on the device and press
CMD.
SUPERVISION TIME
Enter 3as the SUPVSN TIME, and then press CMD.
NEXT ZONE
At the NEXT ZONE?, prompt, select NO.
NEXT ZONE? NO YES
WIRELESS ZONE? YES
SERIAL NO:
SUPVSN TIME: 3
NEXT ZN? NO

1164/1164NS Installation and Programming Guide 5
BELL OPTIONS
Press CMD until BELL OPTIONS displays, and then press a
select key or area.
FIRE BELL ACTION
At FIRE BELL ACTION FIRE TYPE:, select T(temporal) as the
action type.
Note: Program this option to enable cadence
synchronization with other 1164s on the system.
BELL OPTIONS
FIRE BELL ACTION...
FIRE TYPE: T

1164/1164NS Series Installation and Programming Guide6
SELECT A LOCATION
Use the LED survey operation to select a proper location for the smoke detector. The LED
survey operation allows one person to confirm communication with the wireless receiver
or panel while the cover is removed. Because the smoke detector’s transmitter LED is not
visible, use a separate 1100 Series transmitter for the LED survey operation, such as the
1106 Universal Transmitter.
1. Hold the 1106 in the exact desired location.
2. Press the tamper switch on the 1106 to send data to the panel and determine if
communication is confirmed or faulty.
Confirmed: If communication is confirmed, for each press or release of the
tamper switch the LED blinks immediately on and immediately o.
Faulty: If communication is faulty, the LED remains on for up to eight
seconds or flashes multiple times in a quick succession. Relocate the wireless
receiver until the LED confirms clear communication.