DMX4ALL DMX-Splitter 4 User manual

DMX-Splitter 4
User Manual

DMX-Splitter 4 2
For your own safety, please read this user manual and warnings carefully
before installation.
Contents
Description.................................................................................................................. 3
Data Sheet.................................................................................................................. 4
Content....................................................................................................................... 4
LED-Display................................................................................................................ 4
Connection ................................................................................................................. 5
Dimensions................................................................................................................. 6
Accessories ................................................................................................................ 7
CE-Conformity ............................................................................................................ 8
Disposal...................................................................................................................... 8
Risk-Notes .................................................................................................................. 9

DMX-Splitter 4 3
Description
The DMX-Splitter 4 is a compact DMX-Divider with one DMX-Input signal which
provides these at four galvanically isolated outputs.
Spannungs-
versorgung
DMX
DMX
Interface
DMX
Interface
DMX
Interface
DMX
Interface
DMX
Interface
DMX
DMX
DMX
DMX
Power
IN
OUT
IN
OUT
IN
OUT
IN
OUT
4 galvanically isolated outputs
The DMX-Splitter 4 is a compact DMX-Divider with one DMX-Input signal which
provides these at four galvanically isolated outputs.
Extremely light construction
Extremely light DC/DC converters are used for galvanic isolation.
Power supply via one power supply unit
The power supply occurs via one power supply unit. The voltage range is between
8V up to 24V.
Compact design for top hat rail mounting
The DMX-Splitter 4 is suitable for installation in top hat rail mountings with a width of
7cm due to its small size.
LED-Display
Two LEDs show clearly the current operation mode.
Top hat rail mounting available
Suitable for the DMX Splitter 4 the DIN rail housing 700 is available as accessory.

DMX-Splitter 4 4
Data Sheet
Power supply: 8-24V DC
(350mA@12V; 200mA@24V)
Input: 512 Channels
Output: 4x 512 Channels
galvanically isolated
Connections: Screw terminals
Dimensions: 64,2mm x 82mm
Content
1x DMX Splitter 4
1x Quick manual german and english
LED-Display
LED green
The green LED lights up as soon as operation voltage is connected.
LED yellow
The yellow LED lights up as soon as a DMX signal is connected to DMX-IN.

DMX-Splitter 4 5
Connection
DMX-Splitter 4
GND
V+
GND
DMX-
DMX+
DMX-
GND
GND
DMX-
DMX+
GND
DMX-
DMX+
GND
DMX-
DMX+
DMX+
DMX-
GND
DMX+
DMX IN
DMX OUT 1 DMX OUT 2 DMX OUT 3 DMX OUT 4
POWER 12-24V
If more than 4 DMX-Outputs are needed, several DMX-Splitter 4 can be combined as
follows:

DMX-Splitter 4 6
Dimensions
All details in mm

DMX-Splitter 4 7
Accessories
Top hat rail mounting 700
Power supply 12V

DMX-Splitter 4 8
CE-Conformity
This assembly (board) is controlled by a microprocessor and
uses high frequency. In order to maintain the properties of the
module with regard to CE conformity, installation into a closed
metal housing in accordance with the EMC directive 2014/30/EU
is necessary.
Disposal
Electronical and electronic products must not be disposed in
domestic waste. Dispose the product at the end of its service
life in accordance with applicable legal regulations.
Information on this can be obtained from your local waste
disposal company.
Warning
This device is no toy. Keep out of the reach of children.
Parents are liable for consequential damages caused by
nonobservance for their children.

DMX-Splitter 4 9
Risk-Notes
You purchased a technical product. Conformable to the best
available technology the following risks should not excluded:
Failure risk:
The device can drop out partially or completely at any time without warning. To
reduce the probability of a failure a redundant system structure is necessary.
Initiation risk:
For the installation of the board, the board must be connected and adjusted to
foreign components according to the device paperwork. This work can only be
done by qualified personnel, which read the full device paperwork and understand
it.
Operating risk:
The Change or the operation under special conditions of the installed
systems/components could as well as hidden defects cause to breakdown within
the running time.
Misusage risk:
Any nonstandard use could cause incalculable risks and is not allowed.
Warning: It is not allowed to use the device in an operation, where the safety of
persons depend on this device.

DMX4ALL GmbH
Reiterweg 2A
D-44869 Bochum
Germany
Last changes: 22.07.2022
© Copyright DMX4ALL GmbH
All rights reserve. No part of this manual may be reproduced in any form (photocopy, pressure, microfilm or in
another procedure) without written permission or processed, multiplied or spread using electronic systems.
All information contained in this manual was arranged with largest care and after best knowledge. Nevertheless,
errors are to be excluded not completely. It is pointed out that neither a guarantee nor the legal responsibility or
any liability for consequences which are due to incorrect information is assumed. This document does not contain
assured characteristics. The guidance and the features may be changed at any time and without previous
announcement.