Docomo FS050W Guide

Data Usage
*There is no data limit
Client List
0/32→ No device connected
1/32→ 1 device connected
Signal Strength
To lock the
screen,
press and
hold the
button
Lock
Press power
button to go back
home screen
Power
Enter the option to
change
ENTER
Move through the
options displayed
on the screen
SELECT
Buttons and Icons
● Windows 11 (64bit)
● Windows 10 (32bit/64bit)
● macOS Mojave 10.14
● macOS Catalina10.15
● macOS Big Sur 11
● macOS Monterey12
● Chrome OS
OS
You can access to the Internet automatically
when you connect your PC to the WiFi router via USB cable.
Connecting PC via USB
FS050W_
FS050W_
Password: ●●●●●
SSID:FS050W●●●●●
Password
SSID
( Network Name)
You can access the Internet
once you join the network.
Select the SSID begin with “FS050W...”
The SSID and password are displayed
to the back of your WiFi.
Press the power button,
and hold it for 5 seconds.
Enter the password on
your PC or smartphone.
3.
Select the network on
your PC or smartphone
2.
Turn on your WiFi
1.
Connecting with a Smartphone or PC
*For more information, please turn over page.
START GUIDE
ver.1.2
docomo FS050W
WiFi Setup Start Guide

TEL: [phone]
MAIL: [email protected]fi-rental-store.jp
9:30AM 6:30PM (Weekdays Only)
Pleasemakeinquirestothefollowing.
1．Access to WebUI
2． WLAN(Wi-Fi)/USB
→Privacy Separator
→ChangeʻEnable’ to ‘Disable’
→Apply
3． Done!
Turn Off Privacy Separator
1．With the PC or smartphone browser
connected to your WiFi, enter
"http://192.168.100.1/".
2．When the login screen appears,
enter the password "admin".
3． Input a new password.
Access to Web UI

［How to reset］
1. Open the back cover with the power on.
2. Press and hold the reset button for 5 seconds.
3. When "FUSISOFT" appears on the LCD screen,
the reset is complete.
4. After the reset, the device will display the initial setup screen.
Press the ENTER button on the side of the device 7 times to complete the initial setup.
5. You will need to set up for 'eSIM' for the Internet connection. Please see below.
［How to setup 'eSIM'］
1. Use the "SELECT" button on the side of the device to move through the WiFi screen, to the "SIM" icon.
2. Press the "ENTER" button to enter SIM Settings.
3. Use the "SELECT" button to move to "eSIM", and confirm your choice by pressing the "ENTER" button.
4. Done!
［How to setup Language to English］
1. Move to the gear icon on the WiFi screen by using the "SELECT" button on the side of the device.
2. Press the "ENTER" button to enter Settings.
3. Choose " システム ", and then " 言語 ". You will see "English" for language options.
Reset
When something is wrong with your WiFi, try resetting it. Temporary failure will be cleared.
Reset 

Turn Off Privacy Separator
To connect to a printer wirelessly, the privacy separator for WiFi
router needs to be disabled.
The privacy separator can be changed in WebB UI.
Please refer to the bottom of this page for instructions on
accessing Web UI.
Try resetting your WiFi router (instructions below).
Temporary Failure
The actual speed may vary depending on the time and locations.
Please try again later.
Internet Congestion
If the SIM setting is not set to 'eSIM', you'll be out of coverage.
Please change the SIM setting to 'eSIM' by operating the WiFI.
Please note, after a device reset, the default setting is not
'eSIM'.
After resetting, please change the SIM setting to 'eSIM'.
The WiFi router's SIM setting is not set to 'eSIM'.
Please check the signal strength on top left of the WiFi.
When the signal bar shows nothing, try moving to a location
with stronger signal.
*Signal may be weak underground or in large buildings,
even when in the service area.
Poor Connection / No Service
Please check the Client List.
If "0" is displayed, the WiFi router is not connected.
*If "1" is displayed, one device is connected.
Your device is not properly connected to the WiFi router.
"I cannot connect to the printer"
"The connection is unstable"
"The Internet is slow"
"I cannot connect to the Internet"
Troubleshooting docomo FS050W
WiFi Setup Start Guide