Dolmar Ge-4300 l User manual

3ZZ9990197

Instruction Manual

Manuel d’utilisation

Bedienungsanleitung

Handleiding

Manual de instrucciones

Manuale di istruzioni

Manual de Instruções

Instruktionsbok

Ohjekirjanen

Betjeningsvejledning

http://www.dolmar.com

GE-2800 L

GE-3200 L

GE-4300 L

GE-2800 L

GE-3200 L

GE-4300 L

~230V

DOLMAR GE4300L

DOLMAR GENERATOR

GE-4300 L

1011

5 mm

1 2 4

:Dolmar GE-1700 I

:Dolmar GE-1100

:Dolmar GE-2800 L

:Dolmar GE-3200 L

:Dolmar GE-4300 L

:Dolmar GE-2800 IS

:Dolmar GE-3200 IS

:Dolmar GE-4300 IS

:RAS170-

3000001

:RGS170-

4000001

:RGC280-

1000001

:RGC320-

1000001

:RGC430-

1000001

:RAS280-

1000001

:RAS320-

1000001

:RAS430-

1000001

GE-1700 I

GE-1100

GE-2800 L

GE-3200 L

GE-4300 L

GE-2800 IS

GE-3200 IS

GE-4300 IS

88.6 dB

83.9 dB

91.3 dB

92.0 dB

95.4 dB

90.0 dB

90.7 dB

92.0 dB

GE-1700 I

GE-1100

GE-2800 L

GE-3200 L

GE-4300 L

GE-2800 IS

GE-3200 IS

GE-4300 IS

Hamburg, Germany

Shigehiko KOMINAMI Rainer BERGFELD

DOLMAR

Jenfelder Strasse 38 D-22045

Hamburg Germany

Shigehiko KOMINAMI Managing Director

Rainer BERGFELD Managing Director

DOLMAR

Jenfelder Strasse 38 D-22045

Hamburg Germany

90 dB

85 dB

92 dB

96 dB

90 dB

91 dB

93 dB

EN 292

EN 60204

EN 61000

III

DC2165

October. 18. 2005

18. Oktober 2005

18 octobre 2005

18 oktober 2005

18 ottobre 2005

18  2005

18 octubre, 2005

18 de Outubro de 2005

18 oktober 2005

18. lokakuu. 2005

18. oktober, 2005

18. oktober 2005

FOREWORD

Thank you very much for purchasing a DOLMAR POWER GENERATOR.

This manual covers operation and maintenance of the DOLMAR POWER GENERATOR.

This DOLMAR POWER GENERATOR can be used for general electrical equipments, appliances, lamps, tools

as an AC power source. With regards to DC application, the terminals are used only for charging 12 volt battery.

Never use this generator for any other purposes.

Please take a moment to familiarize yourself with the proper operation and maintenance procedures in order

to maximize the safe and efficient use of this product.

Keep this owner’s manual at hand, so that you can refer to it at any time.

Due to constant efforts to improve our products, certain procedures and specifications are subject to change

without notice.

When ordering spare parts, always give us the MODEL, PRODUCTION NUMBER (PROD No.) and

SERIAL NUMBER (SER No.) of your Product.

Please fill in the following blanks after checking the production number on your product.

(Location of label is different depending on the product model.)

CONTENTS

1. SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2. COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3. PRE-OPERATION CHECKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4. OPERATING PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

5. WATTAGE INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

6. MAINTENANCE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7. "HOW-TO" MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PERIODIC OPERATION AND INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TRANSPORTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. PREPARATION FOR STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PROD No. / SER No. (Label)

Please refer to the illustrations on the back page of the front cover or back cover

for Fig. 11to 66indicated in the sentence.

NOTE

GE-4300L(GB)GU212805.7.2810:03AMページ1

1. SAFETY PRECAUTIONS

Please make sure you review each precaution carefully.

Pay special attention to statement preceded by the following words.

“WARNING” indicates a strong possibility of severe personal injury or loss

of life if instructions are not followed.

“CAUTION” indicates a possibility of personal injury or

equipment damage if instructions are not followed.

Do not operate the generator near gasoline or gaseous fuel because of the potential

danger of explosion or fire.

Do not fill the fuel tank with fuel while the engine is running. Do not smoke or use open

flame near the fuel tank. Be careful not to spill fuel during refueling. If fuel is spilt, wipe

it off and let dry before starting the engine.

WARNING

Operate the generator on a level surface.

It is not necessary to prepare a special foundation for the generator.

However, the generator will vibrate on an irregular surface, so choose a level place without surface

irregularities.

If the generator is tilted or moved during operation, fuel may spill and / or the generator may tip over, causing

a hazardous situation.

Proper lubrication cannot be expected if the generator is operated on a steep incline or slope. In such a case,

piston seizure may occur even if the oil is above the upper level.

WARNING

Pay attention to the wiring or extension cords from the generator to the connected device.

If the wire is under the generator or in contact with a vibrating part, it may break and

possibly cause a fire, generator burnout, or electric shock hazard.

Replace damaged or worn cords immediately.

WARNING

Do not operate the generator inside a room, cave, tunnel, or other

insufficiently ventilated area. Always operate it in a well-ventilated area,

otherwise the engine may become overheated, and the poisonous carbon

monoxide gas contained in the exhaust gases will endanger human lives.

Keep the generator at least 1 meter (3 feet) away from any structure or

building during use.

If the generator must be used indoors, the area must be well-ventilated and

extreme caution must be taken regarding the discharge of exhaust gases.

WARNING

Do not place in flammables near the generator.

Be careful not to place fuel, matches, gunpowder, oily cloths, straw, trash, or any other in flammables near

the generator.

WARNING

Do not enclose the generator nor cover it with a box.

The generator has a built-in forced air cooling system, and may become overheated if it is enclosed.

If generator has been covered to protect it from the weather during non use, be sure to remove it and keep

it well away from the area during generator use.

WARNING

CAUTION

GE-4300L(GB)GU212805.7.2810:03AMページ2

Do not contact the generator to a commercial power line. Connection to a commercial

power line may short circuit the generator and ruin it or cause electric shock hazard. Use

the transfer switch for connecting to domestic circuit.

WARNING

Engine becomes extremely hot during and for some time after operation. Keep

combustible materials well away from generator area.

Be very careful not to touch any parts of the hot engine especially the muffler area or

serious burns may result.

WARNING

No smoking while handling the battery. The battery emits flammable hydrogen gas,

which can explode if exposed to electric arcing or open flame.

Keep the area well-ventilated and keep open flames/sparks away when handling the battery.

WARNING

Do not operate in rain, in wet or damp conditions, or with wet hands.

The operator may suffer severe electric shock if the generator is wet due to rain or snow.

WARNING

Keep children and all bystanders at a safe distance from work areas.

WARNING

If wet, wipe and dry it well before starting. Do not pour water directly over the generator, nor wash it with water.

WARNING

Be extremely careful that all necessary electrical grounding procedures are followed during each and every

use. Failure to do so can be fatal.

WARNING

It is absolutely essential that you know the safe and proper use of the power tool or appliance that you intend

to use. All operators must read, understand and follow the tool/appliance owners manual. Tool and appliance

applications and limitations must be understood. Follow all directions given on labels and warnings. Keep all

instruction manuals and literature in a safe place for future reference.

WARNING

Use only "LISTED" extension cords.

When a tool or appliance is used outdoors, use only extension cords marked "For Outdoor Use". Extension

cords, when not in use should be stored in a dry and well ventilated area.

WARNING

Always switch off generator's AC circuit breaker and disconnect tools or appliances when not in use, before

servicing, adjusting, or installing accessories and attachments.

WARNING

Make sure the engine is stopped before starting any maintenance, servicing or repair.

Make sure maintenance and repair of the generator set are performed by properly trained personnel only.

CAUTION

GE-4300L(GB)GU212805.7.2810:03AMページ3

Symbols and Meanings

In accordance with the European requirements (eec Directives),the specified symbols as shown in the

following table are used for the products and this instruction manual.

Read the operator's instruction manual.

Stay clear of the hot surface.

Exhaust gas is poisonous.

Do not operate in an unventilated room.

Stop the engine before refueling.

Fire, open light and smoking

prohibited.

Caution, risk of electric shock.

HOT, avoid touching the hot area.

Do not connect the generator to

the commercial power lines.

Engine oil

(power and Engine)

Add oil

Battery charging

condition

OFF

(power and Engine)

Alternating current

Direct current

Plus ;

positive polarity

Minus ;

negative polarity

OUT-position of a

bistable push control

IN-position of a

bistable push control

Protective earth

(ground)

Fuse

Choke ;

cold starting aid

Engine start

(Electric start)

Engine stop

Gasoline

Fast

Slow

Fuel start / Open

Fuel stop / Close

PrRated power (kW) COP Continuous power

COS

rRated power factor

frRated frequency (Hz) UrRated voltage (V) IrRated current (A)

Hmax

Maximum site altitude

above sea-level (m) Tmax

Maximum ambient

temperature ( )

mMass (kg)

GE-4300L(GB)GU212805.7.2810:03AMページ4

2. COMPONENTS (See Fig. 11)

3. PRE-OPERATION CHECKS

(See Fig. 22)

1. CHECK ENGINE OIL (See Fig. 22-qq,ww)

Please refer to the illustrations on the back

page of

the front cover or back cover for

Fig. 11to 66

indicated in the sentence.

NOTE

qCONTROL PANEL

wFUEL GAUGE

eFUEL TANK

rRECOIL STARTER (HANDLE)

tEXHAUST OUTLET

yTANK CAP

uFUEL STRAINER

iAIR CLEANER

oSPARK PLUG CAP

!0 OIL DRAIN PLUG

!1 OIL GAUGE (OIL FILLER)

Before checking or refilling oil, be sure generator

is located on stable and level surface with engine

stopped.

■■Remove oil filler cap and check the engine

oil level. (See Fig. 2-q)

qOIL GAUGE

wOIL FILLER

eUPPER LEVEL

rLOWER LEVEL

■■If oil level is below the lower level line, refill

with suitable oil (see table) to upper level line.

Do not screw in the oil filler cap when

checking oil level. (See Fig. 2-w)

qUPPER LEVEL

wLOWER LEVEL

■■Change oil if contaminated.

(See "How-To" Maintenance.)

2. CHECK ENGINE FUEL (See Fig. 22-ee,rr)

■■Check fuel level at fuel level gauge.

(See Fig. 2-r)

qEMPTY (E)

wFULL (F)

e"LEVEL" MARK

rFUEL LEVEL LINE

■■If fuel level is low, refill with unleaded

automotive gasoline.

■■Be sure to use the fuel filter screen on the fuel

filter neck.(See Fig. 2-e)

qFUEL FILTER SCREEN

wTANK CAP

Recommended engine oil:

Use 4-stroke automotive detergent oil of API service class

SE or highergrade (SG, SH or SJ is recommended).

SAE 10W-30 or 10W-40 is recommended for

general, all-temperature use. If single viscosity oil is

used, select the appropriate viscosity for the

average temperature in your area.

Ambient

temperature

Single grade

Multigrade

10W

20W

#20

#30

#40

10W

Do not refuel while smoking or near open

flame or other such potential fire hazards.

Otherwise fire accident may occur.

WARNING

GE-2800 L . . . . . . . . . . . . . . . . . . . . . 0.6

GE-3200 L . . . . . . . . . . . . . . . . . . . . . 0.6

GE-4300 L . . . . . . . . . . . . . . . . . . . . . 1.0

Oil capacity (Upper level) : (L) GE-2800 L . . . . . . . . . . . . . . . . . 10.8

GE-3200 L . . . . . . . . . . . . . . . . . 10.8

GE-4300 L . . . . . . . . . . . . . . . . . 12.8

Fuel tank capacity : (L)

GE-4300L(GB)GU212805.7.2810:03AMページ5

5. GROUNDING THE GENERATOR

4. CHECK GENERATOR SURROUNDINGS.

Make sure you review each warning in

order to prevent fire hazard.

■■Keep area clear of in flammables or

other hazardous materials.

■■

Keep generator at least 1 meter

away

from buildings or other structures.

■■

Only operate generator in a dry, well

ventilated area.

■■Keep exhaust pipe clear of foreign

objects.

■■Keep generator away from open flame.

No smoking!

■■Keep generator on a stable and level

surface.

■■Do not block generator air vents with

paper or other material.

WARNING

OPERATING PROCEDURES

(See Fig. 33,44)

1. STARTING THE GENERATOR

■■To ground the generator to the earth, connect

the grounding lug of the generator to the

grounding spike driven into the earth or to the

conductor which has been already grounded

to the earth. (See Fig. 2-t)

qGROUNDING SPIKE

■■If such grounding conductor or grounding

electrode is unavailable, connect the

grounding lug of the generator to the

grounding terminal of the using electric tool or

appliance. (See Fig. 2-y)

qGROUND TERMINAL

Check the oil level before each operations

as outlined on page 5.

CAUTION

(a) Make sure the appliance is disconnected.

(b)Turn engine switch to " "(CHOKE) position.

(When engine is warm or temperature is high,

start engine with the switch at

""(OPEN)

position.) (See Fig. 3-q)

q""(CLOSE)

w""(CHOKE)

compression point (resistance will be felt), then

return the handle to its original position and pull

briskly. (See Fig. 3-w)

qRECOIL STARTER HANDLE

wPULL BRISKLY

(d)

After starting, allow the starter handle to return to

its original position with the handle still in your hand.

■■Do not connect defective appliances

including lines and plugs.

■■Be sure appliances are not connected

to generator when starting up.

Starting the generator with an

appliance connected could result in

damage to the generator and/or

appliance and in personal injury.

CAUTION

NOTE

When engine fails to start after several attempts,

repeat the starting procedures mentioned

above with the engine switch placed at

""(OPEN) position.

3. CHECKING COMPONENT PARTS

Check following items before starting engine:

■■Fuel leakage from fuel hose, etc.

■■Bolts and nuts for looseness.

■■Components for damage or breakage.

■■Generator not resting on or against any

adjacent wiring.

Make sure you review each warning in

order to prevent fire hazard.

■■Do not refill tank while engine is

running or hot.

■■

Before filling fuel, turn the engine switch

into " "(Fuel stop/close) position.

■■

Be careful not to admit dust, dirt, water

or other foreign objects Into fuel.

■■Wipe off spilt fuel thoroughly before

starting engine.

■■Keep open flames away.

WARNING

GE-4300L(GB)GU212805.7.2810:03AMページ6

(e) After 20 to 30 seconds of warm-up is completed,

turn the engine switch to " " (OPEN) position.

(See Fig. 3-e)

q""(CHOKE) w""(OPEN)

(f) Make sure the pilot lamp is on.

This indicates that the generator is properly

operating.

NOTE

■■If the pilot lamp is off, Set the AC breaker

to "ON" position.

■■If no generating condition is found out,

please consult nearest DOLMAR factory

or authorized service center.

■■Make sure that the appliance is switched OFF before connecting it to the generator.

■■Do not move the generator while it is running.

■■Be sure to ground the generator if the connected appliance is grounded. Failure to

ground unit may lead to electrical shock.

WARNING

2. USING ELECTRIC POWER

(1) CONTROL PANEL

1 2

5 4

qPILOT LAMP

wAC CIRCUIT BREAKER

eAC RECEPTACLES

rGROUND TERMINAL

tENGINE SWITCH

(2) AC APPLICATION

(a) Make sure the pilot lamp is turned on.

(b) Turn off the switch(es) of the electrical

appliance(s) before connecting to the

generator.

into the receptacle.

(d) Turn on the switch of the appliance.

GE-4300L(GB)GU212805.7.2810:03AMページ7

3. STOPPING THE GENERATOR

(a)

Turn off the power switch of the electric equipment

and unplug the cord from receptacle of the generator.

(b) Allow the engine about 3 minutes to cool down

at no load before stopping.

""(CLOSE)

(See Fig. 4-w)

q""(OPEN)

w""(CLOSE)

4. OIL SENSOR (See Fig. 44-ee)

qOIL SENSOR

(a) The oil sensor detects the fall in oil level in the

crankcase and automatically stops the engine

when the oil level falls below a predetermined

level.

(b) When engine has stopped automatically, switch

off generator's no fuse breaker, and check the

oil level.

Refill engine oil to the upper level as instructed

on page 5 and restart the engine.

procedures, check the oil level.

Do not remove OIL SENSOR PROBE when

refilling with oil.

Remove oil filler cap on the opposite side

of carburetor.

CAUTION

NOTE

When the AC circuit breaker turns off during

operation, the generator is over loaded or the

appliance is defective.

Stop the generator immediately, check the

appliance and / or generator for overloading, and

have repaired as necessary by DOLMAR factory

or authorized service center.

■■Be sure to ground the generator if the

connected electrical device is grounded.

■■Failure to ground unit could lead to

electrical shock

WARNING

■■

Check the amperage of the receptacles,

and be sure not to take a current exceeding

the specified amperage.

■■Be sure that the total wattage of all appliances

dose not exceed the rated output of the generator.

■■Be sure to ground the generator if the

connected electrical device is grounded.

WARNING

Do not put foreign objects into the plug

receptacle.

CAUTION

GE-4300L(GB)GU212805.7.2810:03AMページ8

Some appliances need a "surge" of energy when starting.

This means that the amount of electrical power needed to start the appliance may exceed the amount

needed to maintain its use.

Electrical appliances and tools normally come with a label indicating voltage, cycles / Hz, amperage (amps)

and electrical power needed to run the appliance or tool.

Check with your nearest dealer or service center with questions regarding power surge of certain appliances

or power tools.

■■Electrical loads such as incandescent lamps and hot plates require the same wattage to start as is

needed to maintain use.

■■Loads such as fluorescent lamps require 1.2

to 2 times the indicated wattage during start-up.

■■Loads for mercury lamps require 2 to 3 times the indicated wattage during start-up.

■■Electrical motors require a large starting current. Power requirements depend on the type of motor and

its use. Once enough "surge" is attained to start the motor, the appliance will require only 50% to 30%

of the wattage to continue running.

■■Most electrical tools require 1.2 to 3 times their wattage for running under load during use. For example,

a 5000 watt generator can power a 1800 to 4000 watt electrical tool.

■■Loads such as submersible pumps and air compressors require a very large force to start. They need 3

to 5 times the normal running wattage in order to start.

For example, a 5000 watt generator would

only be able to drive a 1000 to 1700 watt pump.

5. WATTAGE INFORMATION

To determine the total wattage required to run a particular electrical appliance or tool, multiply the voltage

figure of the appliance/tool by the amperage (amps) figure of same. The voltage and amperage (amps)

information can be found on a name plate which is normally attached to electrical appliances and tools.

NOTE

The following wattage chart is general guide only. Refer to your specific appliance for

correct wattage.

Applications

Applicable Wattage (approx. W)

GE-4300 L

3300

1700

GE-2800 L GE-3200 L

1600

50Hz

700

Incandescent lamp, Heater 2100 2400

Fluorescent lamp, Electric tool 1100 1200

Mercury lamp 800 1000

Pump, Compressor 450 500

GE-4300L(GB)GU212805.7.2810:03AMページ9

6. MAINTENANCE SCHEDULE

Nominal

cross

section

A.W.G.

Allowable

current

No.of strands

/ strands dia.

Resistance

Current Amp.

No./mm Ω/100m

mm2No. A1A 3A 5A 8A 10A 12A 15A

0.75 18 730/0.18 2.477 2.5V 8V

12.5V

─ ─ ─ ─

Voltage drop

1.27 16 12 50/0.16 1.486 1.5V 5V 7.5V 12V 15V 18V ─

2.0 14 17 37/0.26 0.952 1V 3V 5V 8V 10V 12V 15V

3.5 12 to 10 23 45/0.32 0.517 ─1.5V 2.5V 4V 5V 6.5V 7.5V

5.5 10 to 8 35 70/0.32 0.332 ─1V 2V 2.5V 3.5V 4V 5V

VOLTAGE DROP IN ELECTRIC EXTENSION CORDS

When a long electric extension cord is used to connect an appliance or tool to the generator, a certain

amount of voltage drop or loss occurs in the extension cord which reduces the effective voltage available for

the appliance or tool.

The chart below has been prepared to illustrate the approximate voltage loss when an extension

cord of 100 meters

is used to connect an appliance or tool to the generator.

DAILY

■Check oil level.

■Check all components according to "PRE-OPERATION

CHECKS."

EVERY 50 HOURS

■Wash cleaner element. -more often if used in dirty or dusty

environments.

■Check spark plug, clean if necessary.

EVERY 100 HOURS ■

Change engine oil. *-more often if used in dusty or dirty environments

EVERY 200 HOURS ■Adjust spark plug gap.

■Clean fuel strainer.

EVERY 500 HOURS

■Replace spark plug and cleaner element.

■Clean and adjust carburetor,valve clearance, and valve seat

along with cylinder head.

EVERY 1,000 HOURS

(24 MONTHS)

■Inspect control panel parts.

■Check rotor and starter.

■Replace engine mount rubber.

■Overhaul engine.

■Change fuel lines.

NOTE : (*)

■■Initial oil change should be performed after first twenty (20) hours of use. Thereafter change oil every

100 hours.

■■Before changing the oil, check for a suitable way to dispose of the old oil.

Do not pour it down sewage drains, onto garden soil or into open streams.

Your local zoning or environmental regulations will give you more detailed instructions on proper disposal.

GE-4300L(GB)GU212805.7.2810:03AMページ10

2. SERVICING THE AIR CLEANER

(See Fig. 55-ww)

Maintaining an air cleaner in proper condition is

very important.

Dirt induced through improperly installed,

improperly serviced or inadequate elements

damages and wears out engines. Keep the

element always clean.

(a) Unhook the cover and remove the cleaner

element.

qwELEMENT (Urethane form)

(b) Urethane form : Wash the element with fresh

water. Squeeze out the water then dry the

element. (Do not twist.)

3. CLEANING AND ADJUSTING

SPARK PLUG (See Fig. 55-ee,rr)

(a) If the plug is contaminated with carbon, remove

it using a plug cleaner or wire brush.

(b) Adjust the electrode gap to 0.6 to 0.7 mm.

qSPARK PLUG

wPLUG WRENCH

eSPARK PLUG CAP

4. CLEANING FUEL STRAINER

(See Fig. 55-tt)

Dirt and water in the fuel are removed by the fuel

strainer.

qFUEL STRAINER CUP

(a) Remove the strainer cup and throw away water

and dirt.

(b) Clean the screen and strainer cup with gasoline.

to avoid fuel leak.

7. "HOW-TO" MAINTENANCE

(See Fig. 55)

1. ENGINE OIL CHANGE (See Fig.

55-qq)

■■Change engine oil every 50 hours.

(For new engine, change oil after 20 hours.)

(a) Drain oil by removing the drain plug and the oil

filler cap while the engine is warm.

qOIL DRAIN PLUG

(b) Reinstall the drain plug and fill the engine with

oil until it reaches the upper level on the oil filler

cap.

■■Use fresh and high quality lubricating oil to the

specified level as directed on page 5.

If contaminated or deteriorated oil is used or the

quantity of the engine oil is not sufficient, the

engine damage will result and its life will be

greatly shortened. 5. CHECKING CARBON BRUSH

(See Fig. 55-yy)

If the brush become excessively worn, its contact

pressure with the slip ring changes and causes a

roughened surface on the slip ring, resulting in

irregular generator performance.

Check the brush every 500 hours or if generator

performance is irregular.

If the brush is 5 mm long or less, replace it with a

new one.

qBRUSH HOLDER

wBRUSH

e5 mm

rM5 BOLT : 1 pc.

tBRUSH COVER

(a) Remove the brush cover.

(b) Disconnect the wire connector and remove the

brush.

position with the slip ring when installing new

brush.

Make sure the engine is stopped before

starting any maintenance, servicing or

repair.

CAUTION

NOTE

It is recommended to use ear protection

when performing operation, maintenance

and repair of the generator set.

Spark plug :

BR-6HS (NGK) or RL86C (CHAMPION)

GE-4300L(GB)GU212805.7.2810:03AMページ11

PERIODIC OPERATION AND

INSPECTION

When furnishing the generator as emergency

electric power source, periodic operation and

inspection are needed.

Fuel (gasoline) and engine oil will be deteriorated

with time, and this causes that the engine is

difficult to start and as the results improper

engine operation and fault.

Since the fuel (gasoline) will be deteriorated

with time, replace fuel (gasoline) with fresh

one periodically; once every three (3)

months is recommended.

CAUTION

(a) Check the fuel (gasoline), engine oil and air

cleaner.

(b) Start engine.

run the engine for over ten minutes.

(d) Check for the following items;

■■Proper engine running.

■■Adequate output and the indicator lamp

turned on properly.

■■The engine switch normally operated.

■■

No leakage of engine oil and fuel (gasoline).

9. TRANSPORTING

When transporting the generator, make sure that

the fuel (gasoline) should be drained from the

tank.

(a) Turn the engine switch to the

""(CLOSE) position.

(b) Drain the fuel from the tank.

■■To prevent fuel spillage due to the

vibration and impact, never transport

the generator with the fuel (gasoline)

filled in the tank.

■■Secure the tank cap thoroughly.

■■To avoid the risk of the gasoline

flammability, never leave the generator

in an area exposed to direct sunlight or

high temperatures for a long time.

■■

Keep the fuel (gasoline) in the exclusive

gasoline storage tank made by steel

when transporting.

WARNING

■■Do not place any heavy objects on the

generator.

■■Select and place the generator in the

proper position of the transport vehicle

so that the generator not be moved or

fallen down.

Fix the generator with rope as necessary.

CAUTION

GE-4300L(GB)GU212805.7.2810:03AMページ12

10. PREPARATION FOR STORAGE

(See Fig. 66)

The following procedures should be followed prior to storage of your generator for periods of 6 months or longer.

■■Drain fuel from fuel tank carefully by disconnecting the fuel line.

Gasoline left in the fuel tank will eventually deteriorate making engine-starting difficult.

■■Remove the drain screw of the carburetor.(See Fig. 6-q)

qDRAIN SCREW

■■Change engine oil.

■■Check for loose bolts and screws, tighten them if necessary.

■■Clean generator thoroughly with oiled cloth. Spray with preservative if available. NEVER USE WATER

TO CLEAN GENERATOR !

■■Pull starter handle until resistance is felt, leaving handle in that position.

■■Store generator in a well ventilated, low humidity area.

When generator engine fails to start after several attempts, or if no electricity is available at the output

socket, check the following chart. If your generator still fails to start or generate electricity, contact your

nearest DOLMAR factory or authorized service center for further information or corrective procedures.

11. TROUBLESHOOTING

When No Electricity Is Generated at Receptacle :

When Engine Fails to Start:

Check if engine switch is in its proper position.

Check fuel level.

Check to make sure generator is not

connected to an appliance.

Check spark plug for contamination.

Check engine oil level.

Check spark plug for loose spark plug cap.

Turn engine switch to " "(CHOKE) position.

If empty, refill fuel tank making sure not to overfill.

If connected, turn off the power switch on the

connected appliance and unplug.

Remove spark plug and clean electrode.

If the engine oil level is low, add the oil to the

upper level line on the oil gauge.

If loose, push spark plug cap back into place.

Check if the breaker is not activated with the

overload lamp turned on.

Check if the DC circuit breaker is turned off.

Check AC receptacle for loose connection.

Check to see if engine starting was

attempted with appliances already

connected to generator.

Depress the circuit breaker into " "(ON)

position, after making sure the electric power

level is proper and the electric appliance(s)

are in the normal condition.

Secure connection if necessary.

Turn off switch on the appliance, and

disconnect cable from receptacle. Reconnect

after generator has been started properly.

Carbon brushes are excessively worn

Low power.

GE-4300L(GB)GU212805.7.2810:03AMページ13

12. SPECIFICATIONS

GE-3200 L

Type

Rated power COP kW

Rated voltage V

Rated current A

Pilot lamp

Over current protection (AC line)

Model

Type

Displacement mL

Fuel

Fuel tank capacity L

Rated continuous operation

[Approx.] hours

Oil sensor

Length mm

Width mm

Height mm

Dry weight kg

2.4

Rated power factor 1.0

Rated frequency Hz 50

Exciting system Self exciting

Voltage regulating system AVR type

230

10.4

7.4

Circuit breaker

Standard

EX21

211

Forced air-cooled, 4-cycle, Single cylinder, OHC type gasoline engine

Automotive Unleaded Gasoline

10.8

Standard

Maximum site altitude

above sea-level m 1,000

Maximum ambient

temperature °C 40

Starting system Recoil starter

537

432

475

GE-2800 L

2.1

9.1

8.1

EX17

169

10.8

537

432

475

GE-4300 L

3.3

14.3

7.1

EX27

265

12.8

580

477

508

2-pole, Revolving field type

Single phase

MODEL

GeneratorEngineDimensions

GE-4300L(GB)GU212805.7.2810:03AMページ14

13.WIRING DIAGRAM

GE-2800 L / GE-3200 L / GE-4300 L (50Hz-230V)

Earth

(ground)

terminal

receptacle

(230V)

Blk

Ignition coil

Oil Level Sensor

Engine

Switch

ENGINE

GENERATOR CONTROL PANEL

DC coil

Main coil

Blk

Grn

Org

Blk

Grn/Y

Pilot

Lamp

AC Circuit Breaker

Grn/YGrn/Y

BluBlu Blu

Grn/Y

Spark

Plug

Wiring color code

Blk : Black Grn : Green Y : Yellow R : Red

Blu : Blue Org : Orange W : White Grn/Y : Green/Yellow

Oil Sensor UN

AVR

Brush(-)

Brush(+) Field coil

Exciter

coil

Diode

Rectifier

GE-4300L(GB)GU212805.7.2810:03AMページ15

AVANT-PROPOS

Nous vous remercions d'avoir acquis un GROUPE ÉLECTROGÈNE DOLMAR.

Ce manuel décrit le fonctionnement et l'entretien du GROUPE ÉLECTROGÈNE DOLMAR.

Ce GROUPE ÉLECTROGÈNE DOLMAR peut être utilisé pour les équipements électriques généraux, appareils électriques,

lampes, outils, comme source de courant alternatif. Quant à l'application à C.C., les bornes sont utilisées seulement pour

charger la batterie de 12 volts. Ne jamais utiliser ce groupe électrogène pour aucun autre but.

Prenez quelques instants pour vous familiariser avec les procédures de fonctionnement et d’entretien afin d’utiliser ce

produit dans les meilleures conditions possibles de sécurité et de performance.

Conservez ce manuel à portée de main pour vous y reporter lorsque cela est nécessaire.

Dans le souci d’une amélioration constante de la qualité de nos produits, nous ous réservons le droit de procéder sans

préavis à la modification de certains processus et de certaines caractéristiques.

À la commande de pièces de rechange, veuillez toujours nous indiquer le MODÈLE, le NUMÉRO DE PRODUCTION (No. DE

PROD.) et le NUMÉRO DE SÉRIE (No. DE SÉR.) de votre produit.

Veuillez compléter les parties en blanc suivantes après vérification du numéro de production indiqué sur votre produit.

(L'emplacement de l'étiquette varie selon le modèle de produit).

TABLE DES MATIÈRES

1. PRÉCAUTIONS DE SÉCURITÉ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2. COMPOSANTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3. CONTRÔLES PRÉ-OPÉRATOIRES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4. MODES OPÉRATOIRES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

5. INFORMATION D’ALIMENTATION EN WATTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

6. PROGRAMME D'ENTRETIEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7. ENTRETIEN "COMMENT PROCÉDER" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8. FONCTIONNEMENT PÉRIODIQUE ET INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9. TRANSPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10. PRÉPARATION AU MAGASINAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11. DÉPANNAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. FICHE TECHNIQUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. DIAGRAMME DE CÂBLAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Nº. DE PROD. / Nº. DE SÉR.

(Étiquette)

Voir les illustrations au dos de la page de couverture ou de la dernière page pour

les Fig. 11à 66spécifiées dans le texte.

NOTE

GE-4300L-GU2128-FR05.8.316:22PMページ1

This manual suits for next models

Table of contents

Languages:

Other Dolmar Inverter manuals

Dolmar

Dolmar GE-1100 User manual

Popular Inverter manuals by other brands

Huawei

Huawei SUN2000-33KTL-JP quick guide

m-Dimension

m-Dimension 12WA7N owner's manual

DAB PUMPS

DAB PUMPS PWM 203 Instruction for installation and maintenance

Sima

Sima STP-325 User instructions

FujiFilm

FujiFilm SOLAR FU-SUN-6K-LV user manual

Darfon

Darfon H5001 installation manual

Growatt

Growatt MOD TL3-XA Series Installation & operation manual

Haier

Haier AP24DF1HRA Service manual

Schüco

Schüco SUNNY BOY Series user manual

Rayleigh Instruments

Rayleigh Instruments RI-ENERGYFLOW-MODULAR Series user manual

MEGAREVO

MEGAREVO R5KLNA user manual

Mitsubishi Electric

Mitsubishi Electric FR-A862-E instruction manual

Samlexpower

Samlexpower Soleil 2000-120 owner's manual

AMX

AMX AXC-VG24 Schematic diagram

enphase

enphase AC Combiner Box installation manual

Adventure Kings

Adventure Kings AKSR-BK120W-02 user manual

BYD

BYD MINI ES Battery Base user manual

ims PRO

ims PRO IMS 173 E instructions

Dolmar GE-4300 L User manual

Popular Inverter manuals by other brands