DOM 388 User manual

FOLD
1
2
3
Read all instructions BEFORE assembly and USE of product.
IMPORTANT - RETAIN FOR FUTURE REFERENCE. READ CAREFULLY
BEDSIDE SLEEPER
MANUAL INSTRUCTIONS
Dream On Me Inc.
1532 South Washington Ave, Piscataway TWP, NJ 08854
Tel [phone] Fax [phone]
MADE IN SHANG HAI, CHINA
Item: #388

•When using the bedside sleeper, never place the product near edges of
counter tops, table, or other high surfaces.
•Never allow the mattress pad to be used as a toy.
•To clean,use only mildhousehold soap or detergent and warm water on
a sponge or clean cloth.
•Check your mattress pad for loose screws, worn parts, torn material or
stitching on a regular basis. Replace or repair parts as needed.
•Discontinue use of the bedside sleeper should it malfunction or become
damaged or broken. Please contact Dream On Me for repair or to obtain
replacement parts.
•Adult supervision is necessary.
•The minimum range required for this item is around 1 square meter.
•The bedside sleeper is designed to provide a sleeping area for an infant
until he or she begins to push up on hands and knees or approximately 5
months of age. Move your child to another sleeping product when your
child reaches this stage.
•Always read and follow assembly instructions for each product use (co-
sleeper or bassinet).
•Always use ALL required parts for each use (co-sleeper or bassinet).
•Check instruction manual for a list of required parts. Periodically check
product for loose, damaged, or missing parts.
•DO NOT use bedside sleeper if any parts are missing, damaged, or
broken. Contact Dream On Me for replacement parts and instructionsif
needed. DO NOT substitute parts.
•Keep instructions for future use.
•Always read and follow assembly instructions for each product use
(co-sleeper or bassinet).
•Assemble product according to manufacturer’s instructions for ANY
use (co-sleeper or bassinet).
•If a sheet is used with the mattress pad, use only the one provided by
Dream On Me or one specifically designed to fit the dimension of the
bassinet mattress.
•Please follow all of these instructions to ensure the safety of your child.
•Failure to follow these instructions could result in serious injury or death.
•Retain these instructions forfuture reference.
•NEVER leave child unattended, allowing your child near the bassinet.
•Keep fingers(yours and baby’s)away from hinges when opening or closing
the bassinet. Be certain the bassinet is locked in the open position before
allowing your child near the bassinet.
•Strings can cause strangulation! Do not place items with a string around a
child’s neck, such as hood strings or pacifier cords. Do notsuspend strings
over a bassinet or attach strings to toys.
•Failure to follow these warnings and the instructions could result in
serious injury or death.
•FALL HAZARD — To help prevent falls, do not use this product when
the infant begins to push up on hands and knees, has reached 10lbs,
or reaches approximately 5 months of age, whichever comes first.
SUFFOCATION HAZARD!
Infants have suffocated:
• In gaps between an extra pad and side of the mattress pad
• On soft bedding
• Use ONLY the mattress pad provided by Dream On Me.
• NEVER add a mattress, pillow, comforter, or padding.
!
To reduce the risk of SIDS, pediatricians recommend healthy infants be
placed on their backs to sleep, unless otherwise advised by your physician
!
!

!
1
4
!
To avoid injury from the
infant’s neck caught on the
top rail on the side that is
next to the adult mattress,
the top rail must be no
higher than the adult bed
mattress.
Make sure the removable
side is locked when it is no
longer attached to the adult
bed.
•Entrapment Hazard — To prevent death from
entrapment, co-sleeper must be properly secured to
adult bed using the attachment system.
•There must be no more than 13mm gap between
bedside sleeper and adult bed.
•Check tightness before each use
by pulling bedside sleeper in a
direction away from adult bed.
•If gap exceeds 13mm, DO NOT
use product.
Do not fill the gap with pillows, blankets
or other items that are suffocation
hazards. When it is used as
co-sleeper, the safety belt must be
fastened to the adult bed.
GAP
Notice for using attachment
system.
Fasten the belts and put the
box spring back.
!
!
!
This co-sleeper is designed for use only with adult beds that are
between 17.2 and 22.4 inches from floor to top of adult mattress.
Mattress, box spring,and bed frame must share the same width.
The product cannot attach to the adult
bed if the frame is bigger than the
box spring.
17.2 - 22.4 inches
CORRECT
THE TOP RAIL LOWER THAN THE
ADULT BED MATTRESS.
WRONG
THE TOP RAIL HIGHER THAN THE
ADULT BED MATTRESS.
The bedside sleeper must be properly
secured to adult bed by tightening the
safety belt.
UNACCEPTABLE BED TYPE TOO FAR
TIGHT AND SAFE
!

FOLD
1
2
3
To Open The Bedside Sleeper:
1. Put the product on a flat platform.
2. Lift the two
legs and push
them to vertical
position.
3. Check and make sure
that the two metal pins
work. Then the product is
fixed. Turn it over and put
the mattress pad in.
Mosquito net
Frame
Basket
Mattress pad
Button for
adjusting height
Button for folding
Parts List
Please check to make sure that all of the following parts listed
are included in the box when opened. If there are any missing
parts, please contact Dream On Me before using the product.
Carry bag
How to Clean Co-Sleeper
To clean, use only mild household soap or detergent and
warm water on a sponge or clean cloth.

button for adjusting
height
in use
To Use The Co Sleeper:
1. The height of Co Sleeper is
adjustable. It has 4 gears. One
side of the cot is detachable.
There is a retractable basket
underneath.
Adjust the height of the cot,
i.e., position 1 to 4 in order to
attach it to the adult bed.
2. To remove the flexible side, open the
two zippers and turn two clips on both
ends counterclockwise by 90° to the flat
position, while lifting them to release the
side. To close the flexible side, put the
rail back and turn the two clips as
shown above clockwise by 90° to lock
it. Then, zip up the zippers.
button for folding
3. There are two functional
buttons on the legs of both
sides. It takes two steps to
change the height of the cot.
Push the button with up-arrow
upward and press it with one
hand while using the other
hand to lift the cot. Release the
button when the cot reaches
the suitable height.
To Fold The Co Sleeper:
1. Adjust Bedside Sleeper to
the “FOLD” position, i.e., the
lowest position. Check to see
the mark “FOLD” on both
sides. Then, turn over the cot
and put it on a flat platform.
Press the two long oval
buttons to unlock the fixed
pins.
2. Put the legs
down while pressing
the two buttons for
folding.
3. Put the Bedside Sleeper
base in the center of the frame,
and insert the lower pair of the
cot feet between the frame and
cot base. Then, it is folded
completely.A pair of feet
beneath the frame