Domestia DMC-004-004 User manual

1
USERS MANUAL extension module 4 relay outputs unipolar 16A
DMC-004-004
1DESCRIPTION
The module DMC-004-004 is an extension module 4 outputs unipolar 16A/230Vac.
The module is also provided with 6 potentialfree inputs that can be used to work in
stand-alone mode. The relays can command lighting as well as rolling schutters.
2CONNECTIONS
2.1 Connection of the charges on to the module DMC-004-004
Example: connection of 4 lamps:
Example: connection of 2 shutters

2
2.2 Connection in slave mode
The extension DMC-004-004 module 4 outputs can work as a slave module with:
•A master module DMC/DKS-012-00x
•A master module DMC/DKS-008-001
•A control module DME-LAN-
For the connection and the programming of a control module DME-LAN-
refer to the user manual of the DME-LAN-.
Example of connection with a DMC-012-003 as the master module:
BUS
DMI
DMC-012-003
AP www.domestia.be CLI
RS485
AGND
B
Each contact 10A/250VAC
LN
100-240Vac 50/60Hz
BP
Adres
OUT7 OUT8OUT6OUT5OUT4OUT3OUT2OUT1 OUT9 OUT10 OUT11 OUT12
IN7 IN8IN6IN5IN4IN3IN2IN1 IN9 IN10 IN11 IN12
BACK ENTER
BUS
DMI
Each contact 10A/250VAC
4
31 2
Master Module (address 1-12)
Slave Module (address 13-16)
LN
10A
IN 1 IN 2 IN 3 IN 4 IN 5
IN 6
COM
Each potential-free contact 16A/250VAC
RS485
A
GND
B
www.domestia.be
LED6 LED5
BP
Mode BP
Adres
DMC-004-004
OUT1 OUT4OUT2 OUT3
LED7
LN
100-240Vac 50/60Hz

3
2.3 Connection in Standalone mode (directly controlled by
potential free push-buttons).
The extension module DMC-004-004 4 outputs can also work independently in stand-
alone mode.
-The « Stand-alone » entries IN 1 à IN 4 allow to directly control the outputs OUT
1 à OUT 4.
-The entry IN 5 has the function of switching off the 4 outputs.
-The entry IN 6 has the function of switching on the 4 outputs.
The entries have to be connected to potentialfree contacts (for example a push-
button). No voltage can be applied to the inputs.

4
3CONFIGURATION
3.1 Addressing from the app « Domestia Home
Manager » (via the master module)
When the module is connected to a master module of type DMC-008-001
(starting from the micro-software V1.28), DMC-012-003 or DME-LAN-002
(starting from the micro-software V3.0) it is then possible to address the
DMC-004-004 module with the programming app “Domestia Home
Manager”.
1) Automatic addressing : Click on « Automatic addition» => the
software analyses the bus RS485 to find the connected modules.
After this it is still possible to adapt the module’s address with the
arrows UP and DOWN.
2) Semi-automatic addressing : Click on « Semi-automatic addition »
then push on the addressing button of the module(s) DMC-004-004
to add. Click again on « Semi-automatic addition» to end the
procedure of adding modules.
3.2 Manual addressing
To keep the DMC-004-004 compatible with the old master modules
(DMC-012-002, DME-LAN-001) it is possible to address this module
with the addressing button BP-Adres.
1) Press 4 seconds on the BP-Adres (till the blue LED turns off)
2) Then press the number of times corresponding to the desired
addressing (see addressing table). The LED indicator lights up with
each press. (Maximum delay of 2 seconds between successive
presses)
3) After a delay of 2 seconds after the last press: the blue LED flashes
the number of times the button was pressed to confirm the address.
3.3 Reset addressing
To delete the module’s address press the address button for
between 10 and 14 seconds. When the button is released, the LED
flashes 10x rapidly after a 3 second delay to confirm the action.
Note: When the button is pressed, the LED lights up for 4 seconds and
then goes out and lights up every two seconds until the button is released.
Addressing table
Module’s
address
Output
range
1
1-4
2
5-8
3
9-12
4
13-16
5
17-20
6
21-24
7
25-28
8
29-32
9
33-36
10
37-40
11
41-44
12
45-48
13
49-52
14
53-56
15
57-60
16
61-64
17
65-68
18
69-72
19
73-76
20
77-80
21
81-84
22
85-88
23
89-92
24
93-96
25
97-100
26
101-104
27
105-108
28
109-112
29
113-116
30
117-120
31
121-124
32
125-128
33
129-132
34
133-136
35
137-140
36
141-144
37
145-148
38
149-152
39
153-156
40
157-160
41
161-164
42
165-168
43
169-172
44
173-176
45
177-180
46
181-184
47
185-188
48
189-192

5
3.4 Configuration of the functioning of the module
3.4.1 Configuration from the app « Domestia Home Manager »
Select the ouput from the main window « Configuration of the installation ».
Select the output’s functioning mode. By clicking on the shutter’s icon
you can configure a pair of outputs in mode « Rolling shutters »
3.4.2 Configuration with the setting button of the module (BP-Mode
(only if used in the mode « Stand alone »)
1- Press and hold the "BP-Mode" button until the corresponding blue LED goes
out. (± 4 seconds)
2- Select the channel to be set by pressing the "BP Mode" button repeatedly.
The flashing LED moves with each press.
3- Press and hold the “BP Mode”button to activate the selected channel in the
setting mode. The LED lights up permanently and the channel lights up at the
minimum level.
4-Select « Teleruptor Mode » or « Rolling shutters mode»
In the « Teleruptor Mode » LED6 blinks 1x per second
In the « Rolling shutters mode» lLED6 blinks twice 2x successively every seconds.
5-To return to the selection of the channel to be set (step 2), press and hold
the "BP-Mode" button.
6- To exit the "setting" mode, press "BP-Adres".

6
3.5 Programming
3.5.1 Programming from the app « Domestia Home Manager »
a) From the output configuration, click on "Program push buttons" . The output
will light up.
b) Press for at least 2 seconds the push-button(s) that should drive this output
to associate them.
c) Click on "Program push buttons" again to exit the programming of this
output.
3.5.2 Programming from the buttons of a module DMC-012-003 or DMC-
008-001
1)Via the menu "2.1" configure the 4 outputs of the module in the working
mode you want (the output numbers depend on the addressing).
2)Via menu "4.1" select the output to be programmed and press
ENTER. Press for at least 2 seconds the push- button(s) that should drive this
output to associate it. Press ENTER again to exit the programming of this
output. Repeat the operation for the other outputs.

7
4FUNCTIONING
4.1 Functioning in slave mode
The functioning in slave mode depends on the configuration of master module.
4.2 Functioning in stand-alone mode
A) Outputs configured in the « Teleruptor Mode »:
•By default, inputs 1 to 4 drive outputs 1 to 4 of the module.
Pressing the push button reverses the state of the output.
•Input 5 turns off all outputs.
•Input 6 turns on all outputs.
B) Outputs configured in the « rolling shutters mode»:
•The inputs 1 to 4 drive outputs 1 to 4 of the module (odd outputs for shutters down,
even outputs for shutters up)
The activation of a 'down' relay while 'up' is active will deactivate the 'up' relay
before 'down' is activated.
The activation of an 'up' relay while 'down' is active will deactivate the 'down'
relay before 'up' is activated.
•Continuous pressing will keep the corresponding relay activated as long as it is
pressed and deactivated once the push-button is released.
•Input 5 activates both ‘shutters down’relays.
•Input 6 will activates both ‘shutters up’relays.
Reminder: In stand-alone mode, you don’t have to use an identification module.
(DMI-006-001)
5ERROR CODES
Functioning normally:
The LED associated to the output channel is lit continually when activated, and off
when it is inactive.
In case of malfunction, the table below gives a series of error codes.
STATE
Problem
Possible causes
LED 5 doesn’t blink (in
slave mode)
No communication with
the master module
Verify the connections of the RS485 (between the
the DMC-004-004 and the master module).
Master module not present or no power supply to
the Master. Master module not configured as a
master.
Les LED 1 à 4 lights on
(each) in turn
Impossible to control the
lights.
Verify the connections of the RS485 (between the
the DC-004-004 and the master module).
Shutters up & down
reversed
One/more shutter(s)
goes/go up instead of
down and the opposite
‘Shutter down’must be connected to an odd
output ‘Shutter up’ to an even

8
6TECHNICAL CHARACTERISTICS
Functional characteristics
•6 Stand Alone inputs (to use with potentialfree contacts).
•4 configurables relay outputs.
Electrical characteristics
•Power Supply 230Vac / 50Hz.
•Own consumption: 2,60 W
•Internal non-replaceable fuses
•Relay 16A/250Vac :
oMaximum AC breaking capacity: 4000 VA (resistive)
oMaximum start-up current of the relays:
▪165A max 20ms (incandescent lamps)
▪800A max 200μs (fluorescent lamps)
Operating Temperature
•Stockage : -30°C to + 65°C
•Fonctioning : -10°C to +45°C
CE Marking: This product complies with all applicable directives. The EU Declaration of
Conformity is available on www.domestia.be
7WARRANTIES
The duration of your product’s basic warranty is 2 years from the purchase date, which
must be confirmed with an invoice bearing the name of the seller and the date on
which the sale took place and the serial number(s) of your product(s) clearly indicated
on the invoice which is the only document representing the warranty.
Excluded from this warranty are all the following cases:
•All defective parts due to negligent use, misuse, incorrect maintenance or
installation that does not comply with that specified by the manufacturer
(always refer to the installation and user manual provided with the device).
Repair attempts made by the customer or a third party are not permitted.
Damage caused by accident, force majeure or other causes for which
Domestia cannot be held responsible.
•Fault not effecting the proper functioning or proper use of the equipment.
Domestia
176, rue Jean-Jaurès
4430 Ans
Tél : [phone]
Fax : [phone]
[email protected]
www.domestia.be