Dometic rm 2353 User guide

INSTALLATION AND
OPERATING INSTRUCTIONS
REFRIGERATOR FOR LP-GAS AND ELECTRIC OPERATION
RM 2352 RM 2353
FOR YOUR SAFETY
If you smell g s:
1. Open windows.
2. Dont touch electric l switches.
3. Extinguish ny open fl me.
4. Immedi tely c ll your g s supplier.
FOR YOUR SAFETY
Do not store or use g soline or other
fl mm ble v pors nd liquids in the
vicinity of this or ny other ppli nce.
WARNING: Improper inst ll tion,
djustment, lter tion, service or
m inten nce c n c use injury or
property d m ge. Refer to this
m nu l. For ssist nce or ddition l
inform tion consult qu lified
inst ller, service gency or the g s
supplier.
AVIS
Cet pp reil doit être rép ré
seulement p r un rép r teur
utorisé. Modific tion de
l pp reil pourr it être
extrèmement d ngeruse, et
pourr it c user m l ou mort.
Contents:
Page
Installation 4
Operating Instructions 9
Maintenance & Service 11
Corporate Office
2320 Industrial Par way El hart, IN 46515
USA For Service Center Assistance CANADA
Service Office Call: 800-544-4881 Dometic Distribution Inc.
Dometic Corporation 866 Langs Drive
509 South Poplar Street Cambridge, Ontario
LaGrange, IN 46761 N3H 2N7 Canada
Phone: [phone] Phone: [phone]
825 12 08-00
®
®

3
Refrigerator control panel
LEGEND
A. ON/OFF, Fuel Selector Switch
B. Thermostat Knob, Gas/Electric
C. Flame Failure Safety Valve Push-button
D. Piezo Igniter
E. Flame Indicator
Travel latch
FIG. 2
ABED C
12 volt
terminal block,
3-Way only
Manual gas
shutoff valve
Inlet fitting
Flexible cord
crew for burner cover
Burner jet
Protection cover
Flue baffle
Heater(s)
FIG. 1

4
INSTALLATION
GENERAL INSTRUCTION
This a liance is designed for storage of foods and
storage of frozen foods and making ice.
The refrigerators outlined herein have been design cer-
tified by A.G.A. under the ANSI Z21.19 Refrigerator Stan-
dard for installation in a mobile home or recreational
vehicle and are approved by the Canadian Gas Asso-
ciation.
The certifications are, however contingent on the instal-
lation being made in accordance with the following in-
structions as applicable.
In the U.S.A., the installation must conform with:
1. National Fuel Gas Code ANSI Z223.1 - (latest
edition).
2. Manufactured Home Construction and Safety
Standard Title 24 CFR, Part 3280.
3. Recreational Vehicles ANSI A119.2 - (latest
edition).
The unit must be electrically grounded in accordance
with the National Electric Code ANSI/NFPA 70 - (latest
edition) when installed, if an external alternating current
electrical source is utilized.
4. Any applicable local code.
In CANADA, the installation must conform with:
1. Current CAN/CGA B149 Gas Installation Codes
2. Current CSA Standard Z240.4 GAS-EQUIPPED
RECREATIONAL VEHICLES AND MOBILE
HOUSING.
3. Where a flexible metal connector is used, it must
comply with the provisions of the current Standard
CAN1-6.10, METAL CONNECTORS FOR GAS
APPLIANCES.
4. Any applicable local code
The unit must be electrically grounded in accordance
with the current CANADIAN ELECTRICAL CODE C22
Parts 1 and 2.
VENTILATION
The installation shall be made in such a manner as to
separate the combustion system from the living space
of the mobile home or recreational vehicle. Openings
for air supply or for venting of combustion products shall
have a minimum dimension of not less than 1/4 inch.
Proper installation requires one lower fresh air inta e
and one upper exhaust vent. The ventilation its shown
in this instruction manual have been certified for use
with the refrigerator models listed in the Table.
For Certified Vent System Kits see age 8.
The ventilation its must be installed and used without
modification. An opening toward the outside at floor level
in the refrigerator compartment must be provided for
ventilation of heavier-than-air fuel gases. The lower vent
of the recommended its is provided with proper size
openings. The flow of combustion and ventilating air must
not be obstructed.
The lower side vent is fitted with a panel, which pro-
vides an adequate access opening for ready service-
ability of the burner and control manifold of the refrig-
erator. This should be centered on the bac of the re-
frigerator.
CERTIFIED INSTALLATION
Certified installations require one roof vent and one lower
side vent or optional one upper side vent and one lower
side vent. For Certified Vent System Kits see age 8.
For further information contact your dealer or distribu-
tor.
METHODS OF INSTALLATION
The method of installation is shown in FIG. 3a and 3b. It
is essential that all maximum or minimum dimensions
be strictly maintained, as the performance of the refrig-
erator is dependent on adequate flow of air over the rear
of the refrigerator.
Minimum
ventilation
height
Condenser
FIG. 3a
FIG. 3b
Minimum
ventilation
height
Condenser

5
VENTILATION HEIGHTS
Refer to FIG. 3a, 3b and 4.
CLEARANCES
Minimum clearances in inches to combustible materials
are:
G: Top 0
K: Side 0
L: Bottom 0
M: Rear 1
N: See NOTE: N below.
NOTE: Clearance M is between the rearmost part of
the refrigerator and the wall behind the refrigerator.
NOTE: Ventilation height N
With upper and lower side vent is N the distances be-
tween the bottom of the lower side vent to the top of the
upper side vent.
With roof vent and lower side vent is N the distance
between the bottom of the lower side vent to the roof
material.
For ventilation height, see table VENTILATION
HEIGHTS.
See Figures 3a, 3b and 4.
This method of installation and these clearances will give you adequate space for service and proper installation.
D
HA
D
C
B
N
M
N
M
L
KK
G
Side view View from above
FIG. 4
FIG. 5
Refrigerator Minimum ventilation heights in inches and mm.
model
installation with Installation with roof
RM 2352 upper and lower vent and lower side
RM 2353 side vent vent
inch 34 31
mm 864 787
Overall Recess
Refrigerator Dimensions Dimensions
Model
Height Width Depth Height Width Depth
ABCHWD
RM 2352 inch 30-5/32 21-7/8 22-23/32 29-3/4 20-1/2 21-3/8
RM 2353
mm 766 556 577 756 521 542

6
INSTALLING REFRIGERATOR IN
ENCLOSURE
NOTE: DO NOT install the a liance directly on
car eting. Car eting must be removed or
rotected by a metal or wood anel beneath
the a liance, which extends at least full
width and de th of the a liance.
The refrigerator must be installed in a substantial enclo-
sure and must be level. When installing the refrigerator
in the enclosure, all areas within the recess in which the
refrigerator is installed must be sealed.
Ma e sure that there is a complete seal between the
front frame of the refrigerator and the top, sides and
bottom of the enclosure. A length of sealing strip is ap-
plied to the rear surface of the front frame for this pur-
pose. Also apply a sealing strip to the foremost floor of
the enclosure as shown in fig. 6. The sealing should
provide a complete isolation of the appliances combus-
tion system from the vehicle interior.
NOTE: Be careful not to damage the sealing strip when
the refrigerator is put in place.
Failure to follow the sequence in securing refrigerator in
enclosure can cause lea age between the frame and
cabinet.
When installing the refrigerator, the installer must bloc
the space between the storage cabinet and the top of
the refrigerator, otherwise heat will become trapped in
this space, ma ing the top of the refrigerator hot, thus
reducing the efficiency of the unit.
Securing the Refrigerator
After the refrigerator is put in place, (insuring a combus-
tion seal at the front frame), the refrigerator is to be se-
cured in the enclosure with five screws (not included).
The screws have to be installed in the following order:
STEP 1: Four screws installed through the front
frame. See fig. 7.
STEP 2: One screw installed in rear base. See fig. 7.
In the parts bag there are plugs to be snapped in the
front frame to cover the four screw heads.
FIG. 6
GAS CONNECTION
Hoo up to the gas supply line is accomplished at the
manual gas valve, which is furnished with a 3/8" SAE
(UNF 5/8" -18) male flare connection. All completed con-
nections should be chec ed for lea s with soapy water.
DO NOT use a flame to check for gas leaks.
The gas supply system must incorporate a pressure
regulator to maintain a supply pressure of not more than
11 inches water column.
When testing the gas supply system at test pressures in
excess of 1/2 psig, the refrigerator and its individual
shutoff valve must be disconnected from the gas supply
piping system.
When testing the gas supply system at pressures less
than or equal to 1/2 psig, the appliance must be isolated
from the gas supply piping system by closing its indi-
vidual manual shutoff valve.
In case detailed instructions on the installation and con-
nection to the gas supply are required, contact your
dealer or distributor.
! ARNING
FIG. 7
1
2

7
TESTING LP GAS SAFETY SHUTOFF
The gas safety shutoff must be tested after the re-
frigerator is connected to the LP gas su ly.
To test the gas safety shutoff, proceed as follows:
1. Start the refrigerator according to the instructions
for Gas Operation. See section Operating Instruc-
tions.
2. Chec that the gas flame is lit. This can be ob-
served on the flame indicator E. The red indicator
is in the green field, (ON).
3. Close the gas valve by turning the nob A bac to
OFF position.
4. Wait for one minute.
5. Remove burner cover plates. (See fig. 1).
Open the gas valve by turning nob A to position
(GAS) without pushing the buttons C and D. Apply
a non-corrosive commercial bubble solution to the
burner jet.
6. No bubbles should appear at the opening of the
burner jet. The presence of bubbles indicates a
defective gas safety shutoff, and service is re-
quired.
7. If no bubbles were present at the burner jet, the
gas safety valve is wor ing properly. Rinse jet
thoroughly with fresh water before proceeding. Be
careful not to damage the burner jet.
Replace cover and turn the main switch OFF and
bac ON. See instruction for Gas Operation,
section Operating Instructions. Normal operation of
the burner should return. Allow the burner to
operate for a minimum of 5 minutes.
ELECTRICAL CONNECTION
120 Volts AC Connection
The refrigerator is equipped with a three-prong
(grounded) plug for protection against shoc hazards
and should be plugged directly into a properly grounded
three-prong receptacle. DO NOT cut or remove the
grounding prong from this plug. The free length of the
cord is 1.6 ft. and therefore recommended that the re-
ceptacle be located to the left side of the refrigerator
(viewed from the rear) and approximately 4-6 inches from
the floor (see FIG. 8). This allows easy accessibility
through the vent door. The cord should be routed to avoid
contacting the burner cover, flue cover, or any other com-
ponents that could damage the cord insulation.
12 Volts DC Connection
3-way refrigerator model
The 3-way refrigerator model RM 2353, has one termi-
nal bloc mar ed 12 volts DC located at the bottom left
corner on the bac of the refrigerator.
Correct polarity must be observed when connecting to
the DC supply.
DO NOT use the body or chassis of the vehicle as a
substitute for either of the two conductors. Do not con-
nect any other electrical equipment or lighting to the re-
frigerator circuit.
The refrigerator must be connected by a separate cir-
cuit to the battery with two wires of adequate capacity to
avoid voltage drop when the DC heater is being oper-
ated. The wire gauge should be chosen with consider-
ation to the length: refer to the Table below for wire size.
The 12-volt DC circuit must be fused. Maximum fuse
size is 20 amps.
MAXIMUM TOTAL CONDUCTOR WIRE SIZE
(In Feet and Meters)
FIG. 8
120 Volt AC
receptacle
4 - 6
AWG M2353
3-way
10 25.0 ft.
7.6 m
8 40.0 ft.
12.2 m
The connections must be clean, tight and free from cor-
rosion. If not, a resulting voltage drop will cause a de-
creased cooling capacity.
FIG. 9 Battery
Refrigerator
witch key
Relay
Breaker
point
Ignition
coil
Do NOT o erate the refrigerator on 12 volt when the
vehicle is arked. The am erage draw of the 12-volt
DC heating element can discharge a battery in a very
short time. The installation of a 12-volt DC o erated
refrigerator requires a relay to be installed on the
tow vehicle or in the caravan. The relay will auto-
matically shut off the 12 volt DC ower to the refrig-
erator when the ignition is turned off. (See fig. 9).
! CAUTION

8
CHANGING DOOR S ING TO OPPOSITE
SIDE
A special Hinge Kit must be used to change door swing.
For further information please contact The Dometic Cor-
poration listed on the front page.
INSTRUCTIONS FOR MOUNTING THE
DOOR PANEL
The refrigerator is normally delivered without door panel.
The lower decoration strip and parts bag are taped in-
side the door.
Before starting the mounting wor , chec that the panel
dimensions are in compliance with those given in the
Table and the instructions are read thoroughly.
We recommend to mount the panel on the door before
the refrigerator is installed in the enclosure.
When mounting the panel, proceed as follows:
Slide the panel from the bottom of the door into the
grooves on the vertical edges of the door .
Push the panel upwards, ta e the two plastic panel
stops from the parts bag and put them in the two
holes at the lower door frame.
Put the decoration strip across the door and fasten
it with three screws from the parts bag.
PANEL DIMENSIONS
MAX. THICKNESS 5/32" (4 mm)
REFR.MODEL HEIGHT WIDTH
TYPE MAX. MIN. MAX. MIN.
RM 2352 inch 25-9/32 25-3/16 19-5/8 19-17/32
RM 2353 mm 642 640 498 496
CERTIFIED VENT SYSTEM KITS
REFRIGERATOR KIT
MODEL NO. COMPONENTS PART NO.
RM 2352 2A Roof Base 3103633.XXX*
RM 2353 Roof Cover 3103634.XXX*
Lower Side Vent 3102277.XXX*
Lower Side Vent RM183
3A Upper Side Vent RM123
Upper Side Vent RM123A
Lower Side Vent RM183
Power Vent Asm. 3108705.751**
Upper Side Vent RM123
Upper Side Vent RM123A
Upper Side Vent 3107560.041
Lower Side Vent RM183
Lower Side Vent 3107560.009
* Fill in XXX with color code numbers. For color codes, contact your supplier.
** Alternate instructions forwarded with the Ventilator Kit.
For further information contact your dealer or distributor.

9
OPERATING INSTRUCTIONS
1. To start the refrigerator, turn nob A to position
(GAS).
2. Turn the thermostat nob B to position 4.
3. Push the button C in until it reaches the bottom -
and hold, push the button D for the piezo igniter
several times to light the burner. This can be
observed on the flame indicator E. When the flame
is on, the red indicator is in the green field. (ON).
4. After the gas is lit eep the button C pressed for 10
seconds. Release the button and chec that the
RED indicator is in the GREEN field, (ON).
5. To shut off the refrigerator turn the nob A to OFF
position.
NOTE: After changing an LP tan , or after a long shut
off period, the gas line is li ely to be filled with air. You
may have to repeat the lighting procedure several times
to purge the air out of the gas lines.
IMPORTANCE OF LEVELING A
REFRIGERATOR
In an absorption refrigerator system, ammonia is lique-
fied in the finned condenser coil at the top rear of the
refrigerator. The liquid ammonia then flows into the
evaporator (inside the freezer section) and is exposed
to a circulating flow of hydrogen gas, which causes the
ammonia to evaporate, creating a cold condition in the
freezer.
The tubing in the evaporator section is specifically sloped
to provide a continuous movement of liquid ammonia,
flowing downward by gravity through this section. If the
refrigerator is operated when it is not level and the ve-
hicle is not moving, liquid ammonia will accumulate in
sections of the evaporator tubing. This will slow the cir-
culation of hydrogen and ammonia gas, or in severe
cases, completely bloc it, resulting in a loss of cooling.
Any time the vehicle is par ed for several hours with the
refrigerator operating, the vehicle should be leveled to
prevent this loss of cooling.
The vehicle needs to be leveled only so it is comfortable
to live in (no noticeable sloping of floor or walls).
When the vehicle is moving, the leveling is not critical,
as the rolling and pitching movement of the vehicle will
pass to either side of level, eeping the liquid ammonia
from accumulating in the evaporator tubing.
GAS OPERATION
Before starting the refrigerator, chec that all the manual
gas valves are in the ON position. Do not forget the
manual shutoff valve on the rear of the refrigerator see
FIG. 1.
! ARNING
Most LP gas a liances used in recreational ve-
hicles are vented to the outside of the vehicle.
When arked close to a gasoline um , it is os-
sible that the gasoline fumes could enter this
ty e of a liance and ignite from the burner
flame, CAUSING A FIRE OR AN EXPLOSION.
FOR YOUR SAFETY, when refueling, shut off all
LP gas a liances which are vented to the out-
side.
AC
OFF
OFF
OFF/ON
PUSH WHEN LIGHTING
MAX OFF
2
3
4
5
6
7
AC
OFF
OFF
DC
OFF/ON
PUSH WHEN LIGHTING
MAX OFF
2
3
4
5
6
7
2-WAY Control anel
3-WAY Control anel
AB CDE
ABCDE
FIG. 10

10
ELECTRIC OPERATION
1. Chec to be sure that the power cord is properly
connected to the power supply. (See FIG. 8). If the
refrigerator is equipped for 12 volt DC operation,
the tow vehicle or caravan engine should be
running to prevent discharging the battery.
2. Turn the nob A to the position mar ed AC for
120 volt AC operation or DC for 12-volt DC
operation.
3. Turn the thermostat nob B to position 4.
4. To shut off the refrigerator turn the nob A to OFF
position.
THERMOSTAT
The refrigerator is equipped with a thermostat that can
be adjusted by turning the nob B to different setting to
maintain the desired cabinet temperature.
At OFF In gas operation, the thermostat closes its main
valve and the burner runs continuously at the
bypass rate, just enough to eep the burner lit.
In electrical operation, the contacts in the ther-
mostat are open and the heating elements are
off.
At MAX In gas operation, the thermostat allows the
burner to remain on high flame continuously. In
electric operation, the heating element is ON
continuously. Lowest cabinet and freezer tem-
peratures are obtained at this setting.
The thermostat can be adjusted between MAX and
OFF to obtain the desired cabinet temperature.
The closer the nob is to MAX - the colder the cabinet
temperature. The closer the nob is to OFF - the warmer
the cabinet temperature.
When the thermostat reaches the set temperature, it will
cut the burner bac to bypass or, in electric operation,
shut off the heating element.
The setting of the thermostat is not critical, but we rec-
ommend it be adjusted to maintain a dry frost on the
cooling fins. Adjust the thermostat nob closer to MAX
when the outside temperature becomes warm.
HOW TO USE THE REFRIGERATOR
FOOD STORAGE COMPARTMENT
The food storage compartment is completely closed and
unventilated, which is necessary to maintain the required
low temperature for food storage. Consequently, foods
having a strong odor or those that absorb odors easily
should be covered. Vegetables, salads etc. should be
covered to retain their crispness. The coldest positions
in the refrigerator are under the cooling fins and at the
bottom of the refrigerator. The warmer areas are on the
upper door shelves. This should be considered when
placing different types of food in the refrigerator.
FROZEN FOOD STORAGE
COMPARTMENT
Quic frozen soft fruits and ice cream should be placed
in the coldest part of the compartment, which is at the
bottom of the aluminum liner. Frozen vegetables, may
be stored in any part of the compartment.
This compartment is not designed for deep or quic -
freezing of food. Meat or fish, whether raw or prepared,
can be stored in the frozen food storage compartment
provided they are precooled first in the refrigerator. They
can be stored about three times longer in the frozen food
compartment as compared to the fresh food compart-
ment. To prevent food from drying out, eep it in cov-
ered dishes, containers, plastic bags or wrapped in alu-
minum foil.
Ice cubes can be made in the freezer compartment.
For faster ice ma ing, the tray should be placed in direct
contact with the bottom of the freezer compartment.
Ice ma ing is accelerated if the thermostat nob B is
turned to the MAX setting.
It is a good idea to do this a few hours before the antici-
pated need for ice, but be sure to turn the thermostat
bac to normal setting, usually about mid-setting when
the ice is formed. Food in the lower compartment may
be frozen if the setting is left on MAX position.
Total Refrigerated Volume 3 cu.ft.
DEFROSTING
Shut off the refrigerator by turning the nob A to OFF
position. Empty the refrigerator, leaving the drip tray un-
der the finned evaporator. Leave the cabinet and freezer
doors open. Filling the ice tray with hot water and plac-
ing it on the freezer shelf can reduce defrosting time.
NOTE: Defrost water runs from the drip tray to a recep-
tacle at the rear of the refrigerator where it normally
evaporates.
With a lot of defrost water as a result of heavy frosts
build up on the cooling fins, remove the drip tray and
turn it around. Replace the drip tray with the outlet on
the right side of the drip tray and put a bowl under the
outlet.
When the ice has melted, dry the interior of the refrig-
erator with a clean cloth. Replace the drip tray to its origi-
nal position and connect the draining tube.
Replace all food and set the thermostat to MAX for a
few hours. Then reset the thermostat to the desired set-
ting, usually at mid-setting.
DO NOT use a hot air blower. Permanent damage
could result from war ing the metal or lastic arts.
DO NOT use a knife or an ice ick, or other shar
tools to remove frost from the freezer com artment.
They can create a leak in the ammonia system.
CLEANING THE REFRIGERATOR
Cleaning the refrigerator is usually done after it is de-
frosted or put into storage. To clean the interior liner of
the refrigerator, use lu ewarm wea soda solution. Use
only warm water to clean the finned evaporator, gas et,
ice tray and shelves.
NEVER use strong chemicals or abrasives to clean
these arts, as the rotective surfaces will be dam-
aged. It is im ortant to always kee the refrigerator
clean.
! CAUTION

11
SHUT- OFF (STORAGE PROCEDURE)
To shut off the refrigerator, turn the nob A to OFF
position. If the refrigerator will not be in operation for a
period of wee s, it should be emptied, defrosted, cleaned
and the door left ajar. The ice tray should also be dried
and ept outside the cabinet.
6. Remove some insulation wool so that the heater
is accessible.
7. Turn and lift the heater out of its poc et.
8. Fit the new heater into the poc et.
9. Reconnect the heater leads at the top.
10. Reset the insulation and close the lid of the boiler.
11. Replace cover at the burner housing.
12. Reinstall the refrigerator in the enclosure
see Item 2. Refrigerator Removal.
13. Check all connections for gas leaks.
14. Connect 120-volt power cord to the outlet and
reconnect or turn on the 12-volt DC power (if
available).
2. REFRIGERATOR REMOVAL
Before wor ing on the refrigerator, ma e sure the AC
voltage and DC voltage leads (if available) are discon-
nected. Shut off the gas supply at the LP tan . Discon-
nect the gas supply line at the rear of the refrigerator.
Always use a bac up wrench when loosening and tight-
ening connections.
Cap the gas supply line, loosen the screws anchoring
the refrigerator to the enclosure and slide the refrigera-
tor out of the compartment.
When replacing the refrigerator ma e sure that the seal-
ing strips are properly positioned.
Replacement is the reverse of removal. Chec all con-
nections for gas lea s.
Refer to section INSTALLATION, page 4 to 8.
3. PERIODIC MAINTENANCE
To eep your Dometic refrigerator operating efficiently
and safely, periodic inspection and cleaning of several
components once or twice a year is recommended.
A. It is important to eep the area at the bac of the
refrigerator clean. Chec the lower vent, upper vent
and area between these openings for any obstruc-
tions such as bird/insect nests, spider webs, etc.
Clean the coils on the bac of the refrigerator. Use
a soft bristled brush to dust off the coils.
MANUAL HUT OFF VALVE
Shown in open position
Use a quarter dollar or a slotted screwdriver to change position
INLET FITTING NUT
THERMOCOUPLE
PARK ELECTRODE
BURNER TUBE
BURNER MOUNTING CREW
BURNER JET
PRE URE TE T PORT
GAS EQUIPMENT ASSEMBLY
FIG. 11
DO NOT store ex losive substances in the refrig-
erator, such as cigarette lighter gas, gasoline, ether
or the like.
NOTE: Sodium chromate is used for corrosion protec-
tion (less than 2 weight % of the coolant).
MAINTENANCE & SERVICE
The user should be aware of service that must be
done on a regular schedule to kee the refrigerator
o erating ro erly. The service should only be er-
formed by a qualified technician who is familiar with
LP gas systems and refrigerators.
1. CARTRIDGE HEATER
Model RM 2352 is equipped with one electric heater for
120 volt AC, mounted in a poc et of the boiler system.
Model RM 2353 is equipped with two electrical heaters,
one for 120 volt AC and one for 12 volt DC.
To replace the heater proceed as follows:
1. Unplug the refrigerator power cord from the 120-
volt AC outlet. If the refrigerator is equipped for
12-volt DC, disconnect the 12-volt DC power to
the refrigerator.
2. The refrigerator must be removed from the
enclosure, see Item 2. Refrigerator Removal.
3. Remove covers from the burner housing see FIG.
1
4. Disconnect the heater leads at the top of the
refrigerator.
5. With a pair of pliers unfold the lug holding the lid
of the boiler casing and open the lid.
! ARNING

12
It is important to eep the refrigerator area free
from combustible material, gasoline and other
flammable vapors or liquids.
NOTE: The following maintenance is required once or
twice a year, but should only be done by a qualified ser-
viceman who is familiar with LP gas systems and refrig-
erators.
B. Chec all connections in the LP gas system (at the
bac of the refrigerator) for gas lea s. The LP gas
supply must be turned on. Apply a non-corrosive
bubble solution to all LP gas connections.
The appearance of bubbles indicates a lea and
should be repaired immediately by a QUALIFIED
SERVICEMAN WHO IS FAMILIAR WITH GAS
SYSTEM AND REFRIGERATORS.
12. Turn on manual gas shutoff valve and chec all
fittings for lea s with soapy water.
13. Connect 120-volt power cord to the outlet and
reconnect the 12-volt DC power (if available).
14. Chec LP gas safety shutoff. See page 7.
4. TROUBLESHOOTING
Refrigerator Does Not Cool Properly
A. Burner jet clogged.
Clean. (See section Maintenance & Service, Item
3. Periodic Maintenance, Paragraph D. Item 1-14).
B. Chec level of refrigerator.
FIG. 13 Electrode
Burner tube
1/8 to 3/16
(3-5 mm)
Clear blue color
of flame
FIG. 12
DO NOT use a flame to check for gas leaks.
C. The LP gas pressure should be chec ed and the
main regulator readjusted if pressure is incorrect.
The correct operating pressure is 11 inches of
water column. The correct place to ta e the LP gas
pressure is at the test port just ahead of the burner
jet. (See FIG. 11).
D. Inspect the flue baffle. It should be reasonably
clean and free of soot. Heavy soot formation
indicates improper functioning of the burner. The
flue and burner both require cleaning in the follow-
ing manner:
1. Unplug the refrigerator power cord from the 120-
volt AC outlet. (See FIG. 8).
2. If the refrigerator is equipped for 12 volt DC.
Disconnect or shut off the 12 volt DC power to the
refrigerator.
3. Turn manual shutoff valve to OFF. (See FIG. 11).
4. Remove cover from the burner housing. (See fig.
1).
5. Disconnect the wire from the high voltage elec-
trode.
6. Remove the burner mounting screw and remove
the burner assembly. (See FIG. 11).
7. Lift out the wire and flue baffle from the top of flue
tube. Clean the flue from the top using a flue brush.
Blowing compressed air into the flue will not
properly clean soot and scale out of the flue tube.
Replace the flue baffle.
8. Clean burner tube with a brush. Blow out burner
with compressed air.
9. Before removing burner jet, clean burner area of
soot and scale that fell out of flue tube. Remove the
burner jet. Soa the jet in wood alcohol and blow it
out with compressed air. Reinstall and tighten
burner jet.
! ARNING
DO NOT use a wire or in when cleaning the burner
jet as damage can occur to the recision o ening.
This can cause damage to the refrigerator or create
a fire hazard.
! ARNING
10. Reinstall burner, being careful that the end of the
burner fits into the slot on the burner brac et.
Chec to ma e sure slots are centered under the
flue tube and the thermocouple is positioned
properly (tip of thermocouple extends over two
slots of burner).
NOTE: The color of the flame shall be clear blue over
the slots of the burner. (See FIG. 12).
11. Be sure to reconnect the wire to high voltage
electrode. Chec the electrode for proper location
and gap. (See FIG. 13).

13
C. Venting problem.
D. Heavy frost buildup on evaporator fins.
Defrost
E. Flue baffle not inserted properly in flue tube.
F. Improperly set thermostat.
(See Operating Instructions, part Thermostat).
G. Burner dirty.
Clean. (See section Maintenance & Service, Item
3. Periodic Maintenance, Paragraph D. Item 1-14).
H. LP gas pressure low at burner.
Set main regulator so pressure does not drop
below 11 inches of water column at pressure tap.
I. Burner not located properly under flue tube.
Relocate
J. Burner damaged.
Replace
K. Odor from fumes.
1. Dislocated burner
2. Damaged burner
3. Dirty flue tube
NOTE: AVOID SPRAYING WATER THROUGH THE
REFRIGERATOR VENTS WHILE WASHING YOUR
RV.
All the above instructions are to be followed closely. The
refrigerator is quality-guaranteed. However, we are not
responsible for any failures caused by improper adjust-
ments and unfavorable installation conditions. Contact
service point or distributor service dept. for assistance.
SPARE PARTS
The following list is a list of commonly used parts, which
should be available, if required, from your Dometic Ser-
vice Center.
A = RM 2352; B = RM 2353
Part No. Description
200 74 19-15/9 A B Jet, No.39
293 06 97-06/1 A B Burner
293 03 79-00/9 A B Electrode
200 71 72-02/2 A B Baffle
293 17 96-01/1 A B Piezo lighter
17 37 71-07/2 A B Heater, 175W, 120V
17 37 35-05/1 - B Heater, 150W, 12V
293 23 37-01/3 A B Thermocouple
200 22 61-24/2 A B Door shelf, 3 pieces
293 26 36-01/8 A B Box
Hinge Kit from right to left and left to right 385 03 04-01
Contact an authorized service center for arts and
re airs as needed

14
Removing and replacing o shelves (General)
The number of shelves and position may vary between refrigerator models.
Put a screwdriver into the slot of the shelf lock.
Turn the screwdriver counterclockwise.
Remove the shelf locks from the wire shelf.
Slide the wire shelf to the left.
The right-hand side of the shelf will come loose.
Lower the right-hand side of the wire shelf and
let the left-hand side slide out of the holes in the
wall.
Slide the lastic lugs into the holes of the wall.
Sna the shelf locks onto the wire shelf.
Slide the shelf into the holes on the right-hand
side.
Insert the ends of the wire shelf on the left-hand
side at the desired osition.

15
RM 2352
RM 2353
293 31 29 4
120 VOLTS AC
L
N
1
2
5
4
11A
1
C
C
B
A
B
C
1
2
4
5
6
7
1
2
4
5
6
7
HEATER 120V AC
SWITCH
THERMOSTAT
BLACK
WHITE
RED
YELLOW/GREEN
GREEN
BLUE
1
2
3
4
5
6
GROUND
6
3
INDICATOR
ADAPTER
THERMO-
COUPLE
120 VOLTS AC
A
C
B
N
L
1
2
4
5
6
7
1
2
4
5
6
7
293 31 30 4
1
2
5
L
N
120 VOLTS AC
1
3
2
DC
C
3
E1
11
31
A
B
4
1
2
3
4
5
6
BLACK
WHITE
RED
YELLOW/GREEN
GREEN
BLUE
A
B
C
D
E
HEATER 12V DC
HEATER 120V AC
SWITCH
THERMOSTAT
TERMINAL BLOCK
6
3
INDICATOR
ADAPTER
THERMO-
COUPLE
B
D
C
N
L
120 VOLTS AC
C
D
A
12 VOLTS DC
1
2
4
5
6
7
1
2
4
5
6
7
1
2
4
5
6
77
6
5
4
2
1
GROUND
12V DC
1
2
1
2
44
55
66
77

16
MO-FO 0235