Domus CHAM-TOUCH-3C User manual

29-31 Richland St. Kingsgrove. Sydney NSW 2208 Australia
Phone: [phone] | Fax: [phone]
[email protected] | www.domuslighting.com.au
Installation Manual
Note: -The lamp must be installed by professional electrician
-Ensure the power supply is switched off before fitting this product
-Do not touch the lamp when in use
-Keep away from hot steam and corrosive gas
Specifications
Type of controller: RGBW touch wall control Cutout (mm): (L) 70mm x (W) 44mm x (D) 20mm
Output signal: RF + Bluetooth Transmission frequency: 2.4GHz
Dimming range: 0.1% - 100% Operating temperature: 0-40°C
Colour: White (Glass) Power consumption: < 15mA
Dimensions (mm): (L) 120mm x (W) 75mm x (D) 29.1mm Operation voltage: 240V
CHAM-TOUCH-3C Date: May 19, 2022 12:19 PM
Variant Item No. Detail
20144 CHAM-TOUCH-3C 3CH Wall Controller
Thank you forpurchasing yournewCHAM-TOUCH-3CWall Controller, Please take the time to read and understand the instruction
sheet below. Failure to do so may void warranty.
Red channel: Click to turn off/on Press and hold
down to increase/decrease light intensity
Green channel: Click to turn off/on Press and
hold down to increase/decrease light intensity
Click to select Warm White, Natural White and
Cool White mixed by RGB colours
Click to play / pause the 10 built-in effects, Press
and hold down to speed up/down the running effects
Press and hold down to
increase/decrease light intensity
Press and hold down to save colour/effect;
Click to recall the saved
Blue channel: Click to turn off/on Press and hold
down to increase/decrease light intensity Click to switch on/off
Touch colour wheel, touch to select R/G/B colour White channel: Click to turn off/on Press and
hold down to increase/decrease light intensity
• Touch sensitive
• Glass interface(white & black)
• Compatible with all universal series RF+Bluetooth receivers
• Radio frequency: 2.4GHz
• Control RGBW colour
• Control 1 zone/area
• Waterproof grade: IP20
Safety & Warnings
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Function Introduction

29-31 Richland St. Kingsgrove. Sydney NSW 2208 Australia
Phone: [phone] | Fax: [phone]
[email protected] | www.domuslighting.com.au
Installation Manual
Note: -The lamp must be installed by professional electrician
-Ensure the power supply is switched off before fitting this product
-Do not touch the lamp when in use
-Keep away from hot steam and corrosive gas
Back side
19.4 mm 43.58 mm
DC Power input
V- V+
DC I NPUT
RF+Bluetoo th Wall
Panel Cont ro ll er
DC Version
RF+Bluetoo th Wall
Panel Cont ro ll er
AC Version
L NL N
AC INPU T
AC Power input
12-24VDC
PSU
AC 100-240V
V- V+
DC I NPU T
RF+Bluetooth Wall
Pan el Co ntroller
DC Version
AC 100-240V
AC Version
RF+Blueto oth Wal l
Panel C ontro ller
AC Version
L NL N
AC INP UT
AC Power
50/60Hz
AC Powe
r
50/60Hz
Function Introduction
Wiring Diagram

29-31 Richland St. Kingsgrove. Sydney NSW 2208 Australia
Phone: [phone] | Fax: [phone]
[email protected] | www.domuslighting.com.au
Installation Manual
Note: -The lamp must be installed by professional electrician
-Ensure the power supply is switched off before fitting this product
-Do not touch the lamp when in use
-Keep away from hot steam and corrosive gas
Operation
1. Do wiring the wall panel & RF+Bluetooth receiver according to wiring diagram
(please refer to the instruction of RF+Bluetooth receiver that you would like to pair with).
2. Power on, then touch the button to turn on the controller, indicator of the controller turned blue.
Built-in 10 colour changing modes are as follows:
Mode 1: Any two colours of RGB mix fade-in & fade-out
Mode 2: RGB three colours mix fade-in & fade-out
Mode 3: RGB three colours mix fade-out & fade-in
Mode 4: RGB flash
Mode 5: RGB three colours fade-in & fade-out successively
Mode 6: RGB three colours fade-in successively
Mode 7: RGB three colours fade-out successively
Mode 8: RGB three colours jump changing successively
Mode 9: R&B two colours mix fade (R in B out), then G fade-in, then R&B mix fade (R out B in), then G fade-out
Mode 10: B fade-out, then G&B mix fade (G out B in), then R&G mix fade (R out G in), then R fade-in
Pair with RF+Bluetooth receiver
Step 1: Click the “Prog. Key” on RF+Bluetooth receiver (or reset power of the
receiver 3 times continuously if the button is not accessible) to set it into pairing
to RF+Bluetooth remote status.
Step 2: Touch the colour wheel, LED lights connected with the RF+Bluetooth
receiver flicker once means the receiver is paired with the wall panel
successfully.
RF+Bluetooth LED Receiver
Prog