DoorKing 1833 Installation instructions

UL 325 Compliant
Use this manual for circuit board 2358-010 Revision B or higher.
HARDwired Installation/
Owner’s Manual
Tracker Expansion Board
Tracker Expansion Board
Tracker Expansion Board
Tracker Expansion Board
Copyright 2016 DoorKing, Inc.All rights reserved.
Date Installed:
Installer/Company Name:
Phone Number:
Leave Manual with Owner
Circuit Board
Serial Number(s)
and Revision Letter:
Provides Access Control System expansion to
manage Up to 24 additional Access Points.
For Models:
1833, 1835, 1837 and 1838 Multi-Door Access Controller
Quad Board
Enclosure
(Not Included)
Single Board
Enclosure
(Not Included)
34
33
32
31
30
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
13
12
11
10
9
8
7
6
5
4
3
2
1
ON
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF
SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Wiegand Compatable
Single Board
Enclosure
with Built-In
Card Reader
(Not Included)
2358-065-L-7-16

2358-065-L-7-16 1
SECTION 1 - TRACKER EXPANSION BOARD INTRODUCTION 2
1.1 General Information
1.2 General System Layout
1.3 Tracker Expansion Boards Layout Options
1.4 Tracker Expansion Board Overview
1.5 Board Input Descriptions
1.6 Setting Board Address (Software - System Relay)
1.7 Relay Identification (Software - System Relay)
2
3
3
4
5
6
7
SECTION 2 - INSTALLATION 8-9
10
10
11
2.1 Single Board Enclosure
2.2 Quad Board Enclosure
2.3 Single Board Enclosure with Card Reader
11
12
13
14
15
16
17
18
19
20-22
SECTION 3 - HARDWIRING 11
3.1 General HARDwiring Information
3.2 Board Addresses 3-10 Communication Line HARDwiring
3.3 Board Addresses 11-18 Communication Line HARDwiring
3.4 MAX Boards Communication Line HARDwiring
3.5 Basic Board Wiring Options at Access Point
3.6 Alarm Wiring Options at Access Point
3.7 All Available Devices at Access Point
3.8 Typical Dual Mode Wiring at 2 Access Points
3.9 Quad Box Wiring
3.10 Gate Operator Data Wiring - Optional Control Wiring
SECTION 4 - PROGRAMMING 23
4.1 LED and Button Descriptions
4.2 Programming
4.3 Programming Step Descriptions
23
23-25
26-28
SECTION 5 - TROUBLESHOOTING 29
5.1 Wiegand Device Data
5.2 Gate Operator Data
5.3 Gate Operator Event (transaction) Reports
5.4 Complete System Information
29
30
31
32
TABLE OF CONTENTS
DoorKing, Inc. reserves the right to make changes in the products described in this manual without notice and without obligation of DoorKing, Inc. to notify any persons
of any such revisions or changes. Additionally, DoorKing, Inc. makes no representations or warranties with respect to this manual. This manual is copyrighted, all rights
reserved. No portion of this manual may be copied, reproduced, translated, or reduced to any electronic medium without prior written consent from DoorKing, Inc.

2358-065-L-7-16
2
SECTION 1 - TRACKER EXPANSION BOARD INTRODUCTION
Use this manual for Tracker Expansion Board 2358-010 Rev B or higher.
The Model 2358Tracker Expansion Board allows you to expand the number of access points that the models 1833, 1835, 1837
and 1838multi-door access controller PC Programmable Entry Systems can control, up to a maximum of 24. One tracker
expansion board is required for each access point. Tracker expansion boards will interface with a variety of wiegand devices
including card readers, RF transmitters, digital keypads, etc. The tracker expansion board will also report gate operator data
from DoorKing intelligent gate operators that have Gate Tracker outputs. In addition to these features, the tracker expansion
boards can also monitor the status of a door, report door ajar and forced entry conditions, sound local alarms, activate a
building alarm system, and has request to exit inputs.
Prior to beginning the installation, we suggest that you become familiar with the instructions, illustrations, and wiring
guidelines in this manual. This will help insure that your installation is performed in an efficient and professional manner.
The proper installation is an extremely important and integral part of the overall access control system. Check all local building
ordinances and building codes prior to installion. Be sure your installation is in compliance with local codes.
IMPORTANT Wireless installation of the access control system and tracker expansion boards will vary
from the HARDwire installation illustrated in this manual, see the instructions in the wireless kits for
wireless installation.
To utilize the tracker expansion board(s), DoorKing Remote Account Manager for Windows software, V 5.3 or higher is required to be
installed on the user supplied PC. The chart below is to assist you in determining if you have the proper access control system and gate
operators to utilize the tracker expansion board.
Model Control Board
Access Control Systems
1833, 1835, 1837, *1838183x-010 Series
1601, 1602, 1603 Barrier
Model
1601-010
Control Board
Gate Operators
1150 Overhead 4402-010
9200, 9500 Slide 4404-010
6500 Swing, 9000 Slide 4405-010
6050, 6100, 6300 Swing 4502-010
9100, 9150 Slide 4602-010
1.1 General Information
• Expands the control capability of selected DoorKing access control systems to manage up to 24 additional access points.
• Provides power and wiegand inputs for almost any wiegand access control device (Card reader, RF receiver, digital keypad etc.). Board
may power two card readers in parallel if required. For example: an entry and exit card reader on a single door.
• Can be used to provide a variety of door monitoring functions, such as sounding an alarm, or activating a building alarm system when
the door is forced or held open.
• Provides a request to exit input (free exit).
• Provides three programmable relay outputs.
• Hold Open Feature unlocks individual doors (or holds open individual gates) when commanded from the system software.
• Monitors transactions from DoorKing intelligent gate operators. Can monitor slide, swing or overhead gate operators and the
parking gate operator (barrier) in PAMS type applications.
• Optional Wireless kit available to connect tracker expansion board(s) to an access control system wirelessly. Maximum distances
between the access control system and tracker expansion boards will vary from the HARD wire run distances illustrated in this manual,
see the instruction manuals with the wireless kits for the correct distances between the hardware.
* 1838Multi-Door Access Controller ONLY. NOT for use with 1838Access Plus.

2358-065-L-7-16 3
WARNING If the access control system is used to control a vehicular gate with an automatic gate operator, the access control device
must be mounted a minimum of six (6) feet away from the gate and gate operator, ten (10) feet recommended, or in such a way that a
person cannot operate the access control device and touch the gate or gate operator at the same time.
Main
Door/Gate
Relay 1
Relay 2
Zone Address
12 Boards maximum for Relay 2/Wiegand 2 ONLY using board addresses 3-10
12 Boards maximum for Relay 1/Wiegand 1 ONLY using board addresses 11-18
Zone Address Zone Address Zone Address Zone Address
Wiegand 1
Wiegand 2
Relay 0
Access Control
System
Power
Power
Each board can be individually
setup for each access point
depending on what functions are
desired. See section 1.3 below for
tracker expansion board options.
Zone addresses will need to be
used when using more than 8
boards per Relay/Wiegand input
(See page 6).
The diagram below shows the maximum number of tracker expansion boards that can be connected to the 1833, 1835,1837 and 1838.
Note: Wiegand 1 will activate Relay 1 and Wiegand 2 will activate Relay 2 at the access control system.
Existing
Alarm System
Tracker
Expansion
Board
2358-010
Local Alarm Separate
Alarm Power
Door Lock Gate Operator
Alarm
Reset
Request
to Exit
Board Power
16.5 VAC, 20 VA
Ground
(Required)
12 GA. Wire
Battery
Back-Up
(Optional)
Gate
Operator 1
Data Input
Gate
Operator 2
Data Input
OR
Gate operator 2 data input:
DoorKing barrier gate operator only.
Gate operator 1 data input:
DoorKing slide, swing or overhead
operators only.
Alarm system outputs
are dry relay contacts.
The diagram below shows the connections needed when all options (gate operator data, alarm outputs, door and reset switches, request to
exit, etc.) available with the 2358tracker expansion board are utilized at an access point.
Tracker expansion board
input will accept most
wiegand 26, 30, 31-bit
access control devices.
Card Reader
Access Control Device
Auxiliary Relay
Alarm Relay
Output Relay
Next
Tracker Expansion
Board (Optional)
Next
Tracker Expansion
Board (Optional)
Communication Line
Optional Reader LED / Beeper Control
1.2 General System Layout
1.3 Tracker Expansion Board Layout Options
Communication lines (Relay 2/Wiegand 2 AND Relay 1/Wiegand 1)
Wireless Kit
(Optional)
See Wireless
Instruction
Sheets
EXIT
PUSH TO
Access Control System
Relay 1/Wiegand 1
or
Relay 2/Wiegand 2
Door Contact
Switch
Tracker
Expansion
Board at
access point
Board
Address 3
Access
Control
Device
Power
Access
Control
Device Power
Access
Control
Device Power
Access
Control
Device Power
Access
Control
Device Power
Access
Control
Device Power
Access
Control
Device Power
Access
Control
Device Power
Access
Control
Device Power
Access
Control
Device Power
Access
Control
Device Power
Access
Control
Device Power
Access
Control
Device Power
Tracker
Expansion
Board at
access point
Board
Address 4
Access
Control
Device
Power
Tracker
Expansion
Board at
access point
Board
Address 5
Access
Control
Device
Power
Tracker
Expansion
Board at
access point
Board
Address 6
Access
Control
Device
Power
Tracker
Expansion
Board at
access point
Board
Address 6
Access
Control
Device
Power
Tracker
Expansion
Board at
access point
Board
Address 7
Access
Control
Device
Power
Tracker
Expansion
Board at
access point
Board
Address 8
Access
Control
Device
Power
Tracker
Expansion
Board at
access point
Board
Address 8
Access
Control
Device
Power
Tracker
Expansion
Board at
access point
Board
Address 9
Access
Control
Device
Power
Tracker
Expansion
Board at
access point
Board
Address 9
Access
Control
Device
Power
Tracker
Expansion
Board at
access point
Board
Address 10
Access
Control
Device
Power
Tracker
Expansion
Board at
access point
Board
Address 10
Tracker
Expansion
Board at
access point
Board
Address 11
Tracker
Expansion
Board at
access point
Board
Address 11
Tracker
Expansion
Board at
access point
Board
Address 12
Tracker
Expansion
Board at
access point
Board
Address 12
Tracker
Expansion
Board at
access point
Board
Address 13
Tracker
Expansion
Board at
access point
Board
Address 14
Tracker
Expansion
Board at
access point
Board
Address 14
Tracker
Expansion
Board at
access point
Board
Address 15
Tracker
Expansion
Board at
access point
Board
Address 16
Tracker
Expansion
Board at
access point
Board
Address 17
Tracker
Expansion
Board at
access point
Board
Address 17
Tracker
Expansion
Board at
access point
Board
Address 18
Access
Control
Device
Power
Zone Address Zone Address Zone Address
CALL
Z
A
Note: If card
reader has
additional
lighting for
outdoor use,
separate power
must be
provided.

2358-065-L-7-16
4
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Gate Operator 1 – Data IN
Gate Operator 1 – Busy
Gate Operator 2 – Data IN
Gate Operator 2 – Busy
Gate Operator 1 & 2 – Common
Wiegand Input – Data 0
Wiegand Input – Data 1
Wiegand Common
12 VDC Wiegand Device Power
Tracker Expansion Board Busy
Gate Operator 1 Power Monitor
Gate Operator 1 Power Monitor
Gate Operator 2 Power Monitor
Gate Operator 2 Power Monitor
Door Ajar Input
Reset Alarm Input
Communication Relay Input
Request To Exit input
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1 Gate Operator 1 – Data IN
Gate Operator 1 – Busy
Gate Operator 2 – Data IN
Gate Operator 2 – Busy
Gate Operator 1 & 2 – Common
Wiegand Input – Data 0
Wiegand Input – Data 1
Wiegand Common
12 VDC Wiegand Device Power
Tracker Expansion Board Busy
Gate Operator 1 Power Monitor
Gate Operator 1 Power Monitor
Gate Operator 2 Power Monitor
Gate Operator 2 Power Monitor
Door Ajar Input
Reset Alarm Input
Communication Relay Input
Request To Exit input
Communication data output to Wiegand 1 or 2 input (Auxiliary Terminal) on the access control system.
Connects to a local alarm.
Set relay to normally OPEN (NO) or normally CLOSED (NC) using relay jumpers on board.
Connects to a alarm reset button.
Connects to a request to exit button.
Connects to an existing building alarm system.
Set relay to normally OPEN (NO) or normally CLOSED (NC) using relay jumpers on board.
Connects to door control (electric strike, maglock) or gate control (gate operator).
Set relay to normally OPEN (NO) or normally CLOSED (NC) using relay jumpers on board.
Optional battery back-up allows the tracker expansion board to maintain operation during power out conditions.
Use .8amp gel cell for single board P/N 1801-008, 3 amp gel cell for 4 boards max. P/N 1801-009.
Use supplied 16.5 VAC, 20 VA transformer (or UL listed equivalent) to power the tracker expansion board.
Max power wire run with 18AWG wire is 100 feet; with 16 AWG wire is 200 feet. Wire polarity does NOT matter.
Gate operator 1 data input from DoorKing slide, swing or overhead gate operators.
Gate operator 2 data input from DoorKing barrier gate operator.
26, 30, 31-bit wiegand access device input ONLY. 500 ft max.
To an approved grounding source (Required).
Communication ONLY to other tracker expansion boards. DO NOT connect to access control system.
Communication to the access control system Relay 1 or 2 (Main Terminal) or other tracker expansion boards.
Monitors 24V AC/DC power from DoorKing slide, swing or overhead gate operators. Wire polarity does NOT matter.
Monitors 24V AC/DC power from DoorKing barrier gate operator. Wire polarity does NOT matter.
Magnetic Door Contact Switch:
Normally Closed: Switch contacts are held OPEN when the door is closed; switch contacts are CLOSED when the door is open.
Common
Card Reader LED/Beeper Control
19
20 Connects to a card reader with LED and beeper indicators. (Available on certain card readers)
Auxiliary Relay
Auxiliary Relay
Alarm Relay
Alarm Relay
Output Relay
Output Relay
Communication Data Output – Common
Communication Data Output – Data 1
Communication Data Output – Data 0
Battery Negative (-12VDC)
Battery Positive (+12VDC)
Earth Ground
16.5 VAC Input Power
16.5 VAC Input Power
Set relay jumper.
Set relay jumper.
Set relay jumper.
Power
Transformer
Battery
Back-Up
1.4 Tracker Expansion Board Overview
34
33
32
31
30
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
13
12
11
10
9
8
7
6
5
4
3
2
1
ON
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF
SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Wireless
Connection
See wireless
instructions.
Board Relay Jumpers
See page 7.
Board Address (System Relays)
See pages 6 and 7.
Board Inputs
See below and next page.
Board Outputs & Power
See below and next page.
Reset Button
Press to reset the board.
Programming
See section 4.
Board Inputs Function / Connection
Common
Card Reader LED/Beeper Control
Note: Relay
contacts are
rated at 1A 30V
maximum.
Italic Text Note:
6-wire Communication line
REQUIRED connections.
See sections 3.2 thru 3.10.
Important Wireless Note:
Wireless kits DO NOT use the
#10, #17, #19, #27, #28and
#29 communication line. Refer
to wireless instructions with
the wireless kits when using
wireless communication.
Auxiliary Relay
Auxiliary Relay
Alarm Relay
Alarm Relay
Output Relay
Output Relay
Communication Data Output – Common
Communication Data Output – Data 1
Communication Data Output – Data 0
Battery Negative (-12VDC)
Battery Positive (+12VDC)
Earth Ground
16.5 VAC Input Power
16.5 VAC Input Power

2358-065-L-7-16 5
1.5 Board Input Descriptions
Gate operator data inputs can only be used with DoorKing vehicular gate operators (see section 1.1). The tracker expansion board receives data
(Terminals 1-5 and 11-14) from the gate operator control board, converts it to wiegand format, and then sends this wiegand data to the access
control system where it is stored in the transaction buffer. The data that is sent from the gate operator control board includes information such as
gate operator cycle count (x100), if an obstruction was hit, if an attempt was made to force the gate, etc. See the back of manual for a complete
listing of all gate operator transactions. In PAMS applications, only one tracker expansion board is required per traffic lane to monitor the gate
operator activity of the slide, swing or overhead gate operator, and the parking gate operator. The tracker expansion board will also monitor the 24
VAC power from the gate operator control board(s). When this power is removed, a “power out” transaction is sent to the access control system.
Gate Operator Data Input
An alarm condition will exist anytime a controlled door is opened without access being granted by the access control system. The request to exit
input (Terminals 18 & 19) allows the door to be opened without activating the tracker expansion board alarm relays, and will not cause the
access system to report a forced condition. The request to exit is typically used at a controlled access point to allow free exit to personnel. A
“Push To Open” button, or a push bar, etc., is connected to the request to exit input on the tracker expansion board. When this input is activated,
the tracker expansion board
output relay will activate causing the door strike or magnetic lock to release allowing the door to be opened.
Request to Exit Input
The door ajar input (Terminals 8 & 15) monitors the status of a controlled access door through a magnetic (typical) door contact switch. This
input tells the tracker expansion board if the door is not fully closed, and will cause the alarm and auxiliary relays on the tracker expansion
board to activate under certain conditions (see section 3 and section 4). Typically, when the door is closed, the switch contacts are closed;
when the door is open, the switch contacts are open.
Door Ajar Input
The reset alarm input (Terminals 16 & 19) overrides the door ajar input allowing a door to be held open when necessary. When this input is
activated, the tracker expansion board will not activate its alarm or auxiliary relays even if the door ajar input is activated (see section 4).
Reset Alarm Input
The relay input (Terminals 17 & 19) is connected to the Relay 1 or Relay 2 in the access control system that activates when a valid device
code is received by the access control system. For example, when a card reader connected to the wiegand input on the tracker expansion
board reads the card code, it inputs this information to the tracker expansion board, which in turn sends the information to the access control
system. The access control system then makes the decision to grant or deny access. If access is denied, a transaction of the denial is made
and nothing else happens. If access is granted, a transaction of the access grant is made, and the access control system activates the
communication relay. This relay output is connected to the tracker expansion board system communication relay input, which then causes the
tracker expansion board output relay to activate. The output relay activation will then open the controlled door (or gate). If two or more tracker
expansion boards are connected to the access system, only the output relay on the tracker expansion board that sent the data will activate.
The tracker expansion board relay strike time is set via the programming on the tracker expansion board (see section 4).
Communication Relay Input (Communication Line to Access Control System’s Main Terminal Relay 1 or Relay 2)
Activation and operation of the AUXILIARY (Terminals 21-22) and ALARM (Terminals 23-24) relays is dependent on the programming on the tracker
expansion board (see section 4). Typically, the auxiliary relay is connected to a local alarm (bell, buzzer, light, etc.) and the alarm relay is connected to
the buildings existing alarm system. These relays provide a dry contact only.
A
uxiliary and Alarm Relays
The Output Relay (Terminals 25-26) activates on command from the access control system, or from a request to exit input. The output relay
releases the door strike (or magnetic lock) to allow entry or exit, or activates a gate operator if the tracker expansion board is used to control a
vehicular gate.
This relay provides a dry contact only.
Output Relay
All data received at the wiegand input terminals and the gate tracker terminals is sent to the access control system in 26, 30, 31-bit wiegand
format from the wiegand output (Terminals 27-28-29).
Communication Data Output (Communication Line to Access Control System’s Auxiliary Terminal Wiegand 1 or Wiegand 2)
Tracker expansion boards can accept wiegand input data from most devices that output their data in a wiegand format. When using 30 or
31-bit wiegand devices, the system will only recognize facility code 255 and lower. An access control device (a card reader for example) is
connected to the tracker expansion board (Terminals 6-7-8-9). When the tracker expansion board receives the wiegand data from the access
device, it sends the data to the access control system where the decision to grant or deny access is made. At the same time, a report is made
of this activity and is stored in the transaction buffer. Two access control devices may be connected to a single tracker expansion board,
however each device will report the same location in the transaction report when connected in this method and each device will activate the
same door (or gate). This may be preferable in some instances. For example, if a vehicular gate uses both a card reader and an RF receiver for
resident access, each of these devices can be connected in parallel. Each device will activate the gate (door) that the output relay of the tracker
expansion board is connected to, and each device will appear in the transaction report with the name assigned to the tracker expansion board
in the software (“Main Gate”, for example, Refer to the Dual Door Mode ).
A
ccess Control Device Input (26, 30, 31-Bit Wiegand)

2358-065-L-7-16
6
1.6 Setting Board Address (Software - System Relay)
Set dial numbers
accordingly with switch.
34
33
32
31
30
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
13
12
11
10
9
8
7
6
5
4
3
2
1
ON
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF
SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
ON
OFF
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
Note: Start at board address 3, the software reserves board address (system relay) 0, 1 and 2 for the access control system ONLY.
Note: Board Addresses 0, 1, 2 & 19 will not generate a wiegand signal.
Example: The switch is OFF and
the dial is set to 3, so the Board
Address is 3. The software uses
the board address as the System
Relay, this means the System
Relay for this board is 3. See
below for all board settings.
Switch
Maximum HARD wire run between tracker expansion boards (up to 12 boards) is 4000 feet TOTAL,
see section 2 for more information about HARDwiring limitations.
Dial Numbers
Maximum HARD wire run between tracker expansion boards (up to 12 boards) is 4000 feet TOTAL,
see section 2 for more information about HARDwiring limitations.
IMPORTANT: DO NOT
set the board address
to 0, 1, 2 or 19.
Switch MUST be ON (1) for
board addresses 10 thru 18.
(Dial number +10).
Switch MUST be OFF (0) for
board addresses 3 thru 9.
(Dial number only).
Board Address 3
System Relay 3
Board Address 4
System Relay 4
Board Address 5
System Relay 5
Board Address 6
System Relay 6
Board Address 7
System Relay 7
Board Address 8
System Relay 8
Board Address 9
System Relay 9
Board Address 10
System Relay 10
Board Address 11
System Relay 11
Board Address 12
System Relay 12
Board Address 13
System Relay 13
Board Address 14
System Relay 14
Board Address 15
System Relay 15
Board Address 16
System Relay 16
Board Address 17
System Relay 17
Board Address 18
System Relay 18
Board addresses 11 thru 18MUST connect to Relay 1/Wiegand 1 on the access control system
Board addresses 3 thru 10 MUST connect to Relay 2/Wiegand 2 on the access control system
When using tracker expansion boards connected to a single access control system, the board addresses on EACH tracker expansion board
should be set so that the Remote Account Manager for Windows (V 5.0 or higher only) software can identify each tracker expansion
board. The software reserves board address 0, 1 and 2 for the access control system. Tracker expansion board address starts with relay
address 3 (see below). IMPORTANT: The software uses the board address number for the System Relay number.
“Zone” Addresses: Board addresses can be set the same (functions as “zones”), but the system’s “tracking” capability will NOT be able to
distinguish SPECIFIC access point activity. Two or more boards with the same board address will be tracked and logged as “zone number”
but not a specific location for that activity. For example, if you have 4 card readers in different locations in a building, and all have the same
board addresses, the software would track that a card reader in the “zone number” was used, but not which specific location it was used.
Zones can be used for a restricted area with multiple entrances inside the complex such as a pool area/tennis courts or community center.
Zones are not recommended if detailed tracker activity reports are required.

2358-065-L-7-16 7
Relay 1
Main Terminal
ONLY Board Addresses 3-10 connect to Relay 2/Wiegand 2 (12 Boards max)
ONLY Board Addresses 11-18 connect to Relay 1/Wiegand 1 (12 Boards max)
Relay 2
Main Terminal
Note: Relay 2 jumper
set to normally OPEN.
NC
NO
16AC
2019181612 13 14 15 17
16ACBAT1NO1NC1C2RY2CA
Auxiliary Terminal
NO NC C
12345 678910 11 12 13 14
Main Terminal
Access
Control
System
Board
Tracker Expansion Board
Wiegand 1 (Aux Terminal)
Wiegand 2 (Aux Terminal)
Relay 2
Jumper
“NO”
Relay 0
NC
NO
RING
HF
1816
HS
ON
CLK
SEN
SPK
VOL
FEED
BACK
RS 232
ELEVATOR
MIC
VOL
OFF
KEYPAD
321
321
321
MASTER
CODE
16AC16ACBAT1NO1NC1C2RY2CAZIMC
5VDCIMDSPKRCOMMICPSWCGNDPHONE
1
2
3
1234 5 67891011121314
1
2
3
4
5
6
Relay 0
Relay 2 Jumper
NO NC C
Access Control System Main Terminal
The models 1833, 1835, 1837 and 1838 access control systems each have THREE relays (Relay 0, 1, and 2). When the tracker expansion
boards is added to this system, the Output Relay on the tracker expansion boards (Terminals 25-26) are identified in the software by the
board address, beginning with board address 3 = System Relay 3 (System Relays 0, 1 and 2 are reserved for the access control board
relays ONLY in the software).
Each of the 3 relays on the tracker expansion board can be set to either Normally Open (NO) or Normally Closed (NC) by setting the board
relay jumper to the desired configuration. Typically, normally OPEN is used.
When tracker expansion boards are used to expand the access control system, Relays 1 and 2 on the access control system circuit board are
used as tracker expansion communication relays. Relay 2 MUST connect to tracker expansion board addresses 3-10 (system relays 3-10)
and Relay 1 MUST connect to tracker expansion board addresses 11-18 (system relays 11-18).
If both Relay 1 and Relay 2 are used to control tracker expansion boards, Relay 0 is used as the Primary Relay that will open the main door or
gate when the resident pushes “9” on their telephone.
Relay 1
Relay 2
Board Relay Jumpers
SOFTWARE
INSTALLED
Your PC connected to the access control system board
(RS-232 terminal).
System Relays for the tracker expansion boards are
identified in the DKS software sequentially by the board
address, beginning with board address 3 = System Relay 3
and ending with board address 18= System Relay 18.
Relays 0, 1 and 2 are “Physically” located on the access
control board. They are identified in the DKS software as
system relays 0, 1 and 2.
Zone addresses CAN be used but MUST be used when
more than 8boards are required for a Relay/Wiegand input.
See previous page about zone addresses.
Main
Door/Gate
Relay 0
1.7 Relay Identification (Software - System Relay)
34
33
32
31
30
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
13
12
11
10
9
8
7
6
5
4
3
2
1
ON
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF
SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Remote Account Manager Software for Windows System Relay Identification
Aux Relay
Alarm Relay
Output Relay
(System Relay)
RS-232
Set relay 2 jumper NO or NC.
Important Wireless Note:
Wireless kits ARE NOT
wired like this. Refer to
wireless instructions with
the wireless kits when using
wireless communication.
Tracker
Expansion
Board at
access point
Board
Address 3
Tracker
Expansion
Board at
access point
Board
Address 4
Tracker
Expansion
Board at
access point
Board
Address 5
Tracker
Expansion
Board at
access point
Board
Address 6
Tracker
Expansion
Board at
access point
Board
Address 6
Tracker
Expansion
Board at
access point
Board
Address 7
Tracker
Expansion
Board at
access point
Board
Address 8
Tracker
Expansion
Board at
access point
Board
Address 8
Tracker
Expansion
Board at
access point
Board
Address 9
Tracker
Expansion
Board at
access point
Board
Address 9
Tracker
Expansion
Board at
access point
Board
Address 10
Tracker
Expansion
Board at
access point
Board
Address 10
Tracker
Expansion
Board at
access point
Board
Address 11
Tracker
Expansion
Board at
access point
Board
Address 11
Tracker
Expansion
Board at
access point
Board
Address 12
Tracker
Expansion
Board at
access point
Board
Address 12
Tracker
Expansion
Board at
access point
Board
Address 13
Tracker
Expansion
Board at
access point
Board
Address 14
Tracker
Expansion
Board at
access point
Board
Address 14
Tracker
Expansion
Board at
access point
Board
Address 15
Tracker
Expansion
Board at
access point
Board
Address 16
Tracker
Expansion
Board at
access point
Board
Address 17
Tracker
Expansion
Board at
access point
Board
Address 17
Tracker
Expansion
Board at
access point
Board
Address 18
Zone AddressZone AddressZone AddressZone Address
Zone Address Zone Address Zone Address Zone Address

2358-065-L-7-16
8
SECTION 2 - INSTALLATION
The location of the tracker expansion board(s) is dependent on the application that it is being used. Tracker expansion boards
can be installed in selected card reader housings, or they can be installed in their own enclosure (enclosures are optional and
not included with the tracker expansion board). DoorKing has two enclosures available for this purpose. The small housing will
hold a single tracker expansion board and the large housing can hold up to four tracker expansion boards. In addition, the large
housing has convenience outlets to power up to four accessory transformers.
Selected models of proximity card readers are available with an enclosure that has ample room for a tracker expansion board to
be mounted inside the housing. This simplifies the installation of the card reader used with the tracker expansion board.
HARDwire Run: Up to 12 tracker expansion boards can be wired to EACH of the TWO communication
lines available (relay 2/wiegand 2 and relay 1/wiegand 1) at the access control system.
tracker
expansion
board
address 4
tracker
expansion
board
address 5
tracker
expansion
board
address 7
tracker
expansion
board
address 10
500 ft
500 ft
2000 ft
100 ft 100 ft
access control system
A second communication
line can be added with the
same wiring limitations shown in examples if desired.
relay 2/wiegand 2
relay 1/wiegand 1
tracker
expansion
board
address 6
farthest board
900 ft away
200 ft
100 ft
tracker
expansion
board
address 8
tracker
expansion
board
address 9
farthest
board
1600 ft
away
farthest
board
2000 ft
away
500 ft
tracker
expansion
board
address 3
Example 3: 4000 ft total, ONLY one HARDwired communication line shown. 8boards are connected to relay 2/wiegand 2.
Communication line to boards are
connected in parallel. Allows “teeing”
of communication cable for optimal
cable routing.
A second communication
line can be wired with the
same wiring limitations shown in examples if desired.
tracker
expansion
board
address 4
tracker
expansion
board
address 3
2000 ft
2000 ft
access control system
NO more boards can be connected to reley 2/wiegand 2 communication line.
relay 2/wiegand 2
relay 1/wiegand 1
farthest
board
2000 ft
away
farthest
board
2000 ft
away
Example 1: 4000 ft total, ONLY one HARDwired communication line shown. 2 boards are connected to relay 2/wiegand 2.
Communication line to boards are
connected in parallel. Allows “teeing”
of communication cable for optimal
cable routing.
A second communication
line can be added with same
wiring limitations shown in
examples if desired.
tracker
expansion
board
address 3
tracker
expansion
board
address 4 tracker
expansion
board
address 5
tracker
expansion
board
address 6 tracker
expansion
board
address 7
tracker
expansion
board
address 8
tracker
expansion
board
address 9
tracker
expansion
board
address 10
All boards are less than 2000 ft away from access control system.
500 ft
200 ft
1900 ft
300 ft
400 ft
150 ft
450 ft
100 ft
access control system
relay 2/wiegand 2
relay 1/wiegand 1
Example 2: 4000 ft total, ONLY one HARDwired communication line shown. 8boards are connected to relay 2/wiegand 2.
Communication line to boards are connected
in parallel. Allows “teeing” of communication
cable for optimal cable routing.
Relay/Wiegand Note:
Relay 2/wiegand 2 MUST be connected to tracker
expansion board addresses 3 thru 10.
Relay 1/wiegand 1 connects to tracker expansion board
addresses 11 thru 18if that many boards are desired.
Zone addresses can be used if desired.
Zone addresses can be used if desired.
Zone addresses can be used if desired.
IMPORTANT Wireless communication maximum distances between the access control system and tracker expansion
boards will vary from the HARDwire run distances illustrated below. See the instruction sheets in the wireless kits and the
Layout and Start-Up Procedure for the correct distances between the hardware when using wireless communication.
IMPORTANT: The maximum distance for a tracker expansion board HARDwire run is 4000 feet TOTAL (1 to 12 boards
can be in a HARDwire run). The farthest boards can be NO more than 2000 feet away from the access control system.

2358-065-L-7-16 9
relay 2/wiegand 2
relay 1/wiegand 1
A second communication
line can be added with same
wiring limitations shown in
examples if desired.
tracker
expansion
board
address 3
tracker
expansion
board
address 4
tracker
expansion
board
address 5
tracker
expansion
board
address 5
tracker
expansion
board
address 6 tracker
expansion
board
address 7
tracker
expansion
board
address 8
tracker
expansion
board
address 9
tracker
expansion
board
address 10
All boards are less than 2000 ft away from access control system.
Zone addresses can be used if desired.
Individual addresses can be used if desired.
Individual addresses can be used if desired.
250 ft 250 ft
Zone Addresses
200 ft
500 ft 600 ft 400 ft 400 ft
300 ft
400 ft
150 ft
450 ft
100 ft
access control system
tracker
expansion
board
address 3
tracker
expansion
board
address 5
tracker
expansion
board
address 5
relay 2/wiegand 2
relay 1/wiegand 1
Example 5: 4000 ft total, ONLY one HARDwired communication line shown. 12 boards maximum with “Zones” are connected to relay 2/wiegand 2.
Communication line to boards are connected
in parallel. Allows “teeing” of communication
cable for optimal cable routing.
Relay/Wiegand Note:
Relay 2/wiegand 2 MUST be connected to tracker
expansion board addresses 3 thru 10.
Relay 1/wiegand 1 connects to tracker expansion board
addresses 11 thru 18if that many boards are desired.
Wiring More Than 8 Boards Note:
Use 6 conductor stranded with overall shield - 18gauge.
ONLY use 18gauge when wiring more than 8boards.
DO NOT connect shield to 2358-010 board common.
DO NOT use twisted pair.
Zone Addresses
tracker
expansion
board
address 3
tracker
expansion
board
address 3
500 ft 600 ft 400 ft 500 ft
tracker
expansion
board
address 3
tracker
expansion
board
address 3
tracker
expansion
board
address 4
tracker
expansion
board
address 4
500 ft 600 ft 400 ft 500 ft
tracker
expansion
board
address 4
tracker
expansion
board
address 4
Zone Addresses
Zone Addresses
A second communication
line can be wired with the
same wiring limitations shown
in examples if desired.
access control system
NO more boards can be connected to reley 2/wiegand 2 communication line.
Example 6: 4000 ft total, ONLY one HARDwired communication line shown. 8boards with “Zones” are connected to relay 2/wiegand 2.
Communication line to boards are connected in
parallel. Allows “teeing” of communication cable
for optimal cable routing.
tracker
expansion
board
address 7
tracker
expansion
board
address 8
tracker
expansion
board
address 9
tracker
expansion
board
address 10
Quad Box
A second communication line can be added with same
wiring limitations shown in examples if desired.
farthest
board
2000 ft
away
farthest
board
1900 ft
away
farthest
board
2000 ft
away
farthest
board
2000 ft
away
access control system
relay 2/wiegand 2
relay 1/wiegand 1
Example 4: 2000 ft total, ONLY one HARDwired communication line shown. 8boards are connected to relay 2/wiegand 2.
1000 ft tracker
expansion
board
address 3
tracker
expansion
board
address 4
tracker
expansion
board
address 5
tracker
expansion
board
address 6
Quad Box
1000 ft
IMPORTANT Wireless communication maximum distances between the access control system and tracker expansion
boards will vary from the HARDwire run distances illustrated above. See the instruction sheets in the wireless kits and the
Layout and Start-Up Procedure for the correct distances between the hardware when using wireless communication.

2358-065-L-7-16
10
Optional quad box enclosure (P/N 2351-081) provides a lockable weather resistant housing for up to four (4) tracker expansion boards.
Includes four (4) terminals and four (4) convenience outlets for power transformers. You may power up to four (4) tracker expansion boards
from a Single 16.5 VAC, 50 VA power transformer (P/N 1508-060). See section 3.9 for quad box wiring information.
2.2 Quad Board Enclosure
4”
3.5”
7”
2.75”
24”
14”
2” 2”
Conduit Placement
Options
(5) 8-Pin Terminals
Communication
Lines
Terminal
Access Point TerminalAccess Point Terminal
Access Point TerminalAccess Point Terminal
Mounting Hole Mounting Hole
Mounting HoleMounting Hole
Tracker
Expansion
Board
Mount
Tracker
Expansion
Board
Mount
Tracker
Expansion
Board
Mount
Tracker
Expansion
Board
Mount
3/4”
3/4” 3/4”
3/4” 3/4”
3/4”
2” 2.5” 2.5” 2.5”
3/4”
3/4”
3/4”
3/4”
3/4”
3/4”
3/4”
3/4”
4”
1”
1”
1”
3/4” Conduit 3/4” Conduit
3/4” Conduit
1” Conduit
1”
Conduit
3/4”
Conduit
Note: Remove convenience outlets power plate
to access knock-outs and mounting hole. Note: Conduit entering in back of housing
knock-outs
knock-outs
knock-outs
Back of Housing
Battery Back-Up Note:
A 12 VDC, 3 amp-hour battery
(P/N 1801-009) can be used to
supply back-up power to four
(4) tracker expansion boards.
Optional single enclosure (P/N 2351-080) provides a lockable, weather resistant housing for a single tracker expansion board.
2.1 Single Board Enclosure
Tracker
Expansion
Board
Mount
3/4”
Conduit
Placement
1” 1”3.75”
1.25”
2.375”
3/4”
Knock-outs
Mounting Hole
Battery Back-Up Note:
A 12 VDC, .8amp-hour battery
(P/N 1801-008) can be used to
supply back-up power to a
single tracker expansion board.
Important Wireless Note: DO NOT remove antenna plugs if
NOT using a antenna that screws into the top of the enclosure
for wireless communication.
If using an external antenna for wireless communication that
uses a coax cable, run it out of the BOTTOM of the enclosure.
DO NOT run coax cable out of the top of the enclosure, it will
leak and cause damage to the circuit board.
8.75”
5.75” 3.625”
Mounting Hole
Optional Screw On Antenna Mounts
for wireless kits ONLY.

2358-065-L-7-16 11
Input:
120V60 Hz
Output:
16.5VAC 20 VA
SECTION 3 - HARDWIRING
Plan your HARDwire runs before starting the installation. Use proper wire for the wiegand lines, power wires, and be sure that
the system is properly grounded. Check all local building ordinances and building codes prior to installing this system. Be sure
your installation is in compliance with local codes.
3.1 General HARDwiring Information
• Use only the supplied power transformers (16.5 VAC, 20 VA) or UL listed equivalent to power the tracker expansion board. You may
power up to four (4) tracker expansion boards from a single 16.5 VAC, 50 VA power transformer.
•Use 18AWG wire for power wire runs up to 100 feet. Use 16 AWG wire for power wire runs up to 200 feet. It is advisable to keep
power wire runs as short as possible. Wire polarity does not matter.
•Do not power any other devices (electric strikes, magnetic locks) from the tracker expansion board power transformer. These devices
must be powered from their own power supply.
•Proper grounding of the system is required. To be effective, ground connections should be made with a minimum 12 AWG wire with
a ground point within 10-feet of the access control system. The ground point must be an electrical panel ground buss, a metallic cold
water pipe that runs in the earth, or a grounding rod driven at least 10-feet into the soil. If there are several components in the access
control system within close proximity to each other, you should consider using a single-point ground system. Check with your
building department for specific grounding guidelines as soil conditions and grounding requirements differ depending on your
geographical location.
• Surge suppressors can significantly reduce the chance of component failure because of static charges or surges. We recommend
using both high and low voltage surge suppressors to help protect equipment from damage. High voltage suppressor P/N 1879-010;
low voltage suppressor P/N 1878-010.
• A 12 VDC, 3 amp-hour battery (P/N 1801-009) can be used to supply back-up power to four (4) tracker expansion boards. Use a
12 VDC, .8amp-hour battery (P/N 1801-007) to back-up a single tracker expansion board. Battery back-up power is optional and
not required for normal tracker expansion board operation.
• Be sure to color code all wires.
Optional built-in wiegand card reader single enclosure provides a lockable, weather resistant, LED lighted housing for a single tracker
expansion board.
2.3 Single Board Enclosure with Card Reader
Power Supply Note:
The power supply that is
supplied with the enclosure
can also be used to power
the tracker expansion board.
Built-In Card Reader with Lighting:
DK Prox Reader - P/N 1815-333
HID Reader - P/N 1815-392
AWID Reader - P/N 1815-292
Mounting Note:
Can be mounted on a DoorKing
gooseneck mounting post.
Tracker
Expansion
Board
Mount
1/2”
Knock-out 6.5”
5.25”4.5”
Mounting
Holes
Optional
Antenna
Mount
Back Side
Card Reader with Lighting
Front Inside Enclosure

2358-065-L-7-16
12
34
33
32
31
30
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
13
12
11
10
9
8
7
6
5
4
3
2
1
ON
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF
SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
3.2 Board Addresses 3 - 10 Communication Line HARDwiring
NC
NO
RING
ON
CLK
SEN
SPK
VOL
FEED
BACK
RS 232
ELEVATOR
1234 5 67891011121314
1
2
3
MIC
VOL
OFF
KEYPAD
321
321
321
MASTER
CODE
16AC16ACBAT
1NO1NC1C
2RY2C
AZIMC
5VDCIMDSPKRCOMMICPSWCGNDPHONE
12 3 4 201918171615
1413
12111098765
NO NC C
Access Control
System Board
Relay 2
Wiegand 2
Auxiliary Terminal
Main Terminal
Relay 0
Relay 1
Board Address 3
Central Office
phone line -
touch tone,
loop start. Switch closure across
terminals 4 & 6 will
activate relay 1 for its
programmed strike time.
Important Note: Relay 2 is used to
control tracker expansion board
addresses 3-10, Relay 1 or Relay 0 can
be used as the Primary Relay that will
open a visitor door or gate when the
resident pushes “9” on their telephone.
Tracker expansion boards connected to Wiegand 2
will activate Relay 2 in the access control system.
Main Door/Gate
Relay 1 or Relay 0
Auxiliary
Terminal
Black #9-Com
White #8-Data 1
Green #7-Data 0
Black #27
White #28
Green #29
Brown #19
Blue #17
Red #10
Tracker Expansion
Board “Busy” #10
Brown #13 Blue #14
To Board Addresses 4 thru 10
12 tracker expansion boards can be connected to Relay 2/Wiegand 2. If more than 12 tracker expansion boards are desired, see next page.
Note: Terminals
can be removed
from board for
easy wiring.
Ground #32
NO
Com
Ground
12 GA. Wire
Use 6 conductor stranded with overall shield. 18- 22 gauge.
ONLY use 18gauge when wiring more than 8boards.
DO NOT connect shield to 2358-010 board common.
DO NOT use twisted pair.
Communication line to additional boards are
connected in parallel. Allows “teeing” of
communication cable for optimal cable routing.
Aux
Power
Power #33
Power #34
Board Power
16.5 VAC, 20 VA
#10 connects
ONLY to tracker
expansion boards
• Maximum HARDwire run between tracker expansion boards is 4000 ft total, but no more than 2000 ft between any two
boards or from the access control system. See section 2.
•DO NOT use twisted pair wire with wiegand output format.
•Auxiliary terminal power transformer on access control system board must be connected. Otherwise, RS-232, elevator control
and wiegand inputs will not function.
•Proper grounding is required! Ground wire should be a minimum 12 AWG.
Notes:
Board address must be set for EACH BOARD wired, see section 1.6.
Power, access control devices, door or gate control, aux and alarm
outputs, door and reset switches, request to exit, etc. wiring is not
shown, see section 3.5-3.8.
Gate operator data wiring is not shown, see section 3.10.
Note: See
section 3.5-3.8
to wire board
options.
Important Wireless Note:
Wireless kits ARE NOT
wired like this. Refer to
wireless instructions with
the wireless kits when using
wireless communication.
Relay 2 Jumper
set to Normally Open
NC
NO
Relay 2/Wiegand 2 to Tracker Expansion
Board Terminal Connection Numbers
Auxiliary Terminal Tracker Terminal
Black #9-Com
White #8-Data 1
Green #7-Data 0
#27
#28
#29
Main Terminal Tracker Terminal
Brown #13-Com
Blue #14-N.O.
#19
#17
Tracker Terminal Tracker Terminal
Red #10-Busy #10
When using multiple tracker boards:

2358-065-L-7-16 13
34
33
32
31
30
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
13
12
11
10
9
8
7
6
5
4
3
2
1
ON
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
NC
WIEG TRUE
RELAY
NO
NC
ALARM
RELAY
NO
NC
MONITOR
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF
SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34
33
32
31
30
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
13
12
11
10
9
8
7
6
5
4
3
2
1
ON
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
NC
WIEG TRUE
RELAY
NO
NC
ALARM
RELAY
NO
NC
MONITOR
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF
SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
NC
NO
RING
ON
CLK
SEN
SPK
VOL
FEED
BACK
RS 232
ELEVATOR
1234 5 67891011121314
1
2
3
MIC
VOL
OFF
KEYPAD
321
321
321
MASTER
CODE
16AC16ACBAT
1NO1NC1C
2RY2CAZIMC
5VDCIMDSPKRCOMMICPSWCGNDPHONE
12 3 4 201918 171615 141312111098765
NO NC C
Access Control
System Board
Relay 1
Relay 2
Auxiliary Terminal
Relay 0
Board Address 11
Board Address 3
Central Office
phone line -
touch tone,
loop start.
Important Note: If both Relay 1 and Relay 2
are used to control tracker expansion
boards, Relay 0 is used as the Primary
Relay that will open a visitor door or gate
when the resident pushes “9” on their
telephone.
Black #27
White #28
Green #29
Ground #32
Auxiliary
Terminal
Black #9
White #8
Green #7
Black #27
White #28
Green #29
Brown #19
Blue #17
Red #10
Brown #19
Brown #15
Blue #17
Red #10
Blue #17
To Board Addresses 4 thru 10
See previous page and next page for additional board wiring.
See next page for additional board wiring.
To Board Addresses 12 thru 18
Up to 12 tracker expansion boards connected to Relay 2/Wiegand 2 THEN connect the next 12 boards to Relay 1/Wiegand 1.
Ground
12 GA. Wire
Ground #32
Ground
Board Power
Switch closure across
terminals 4 & 6 will
activate relay 1 for its
programmed strike time.
Wiegand 1
Wiegand 2
Note: Terminals can be removed
from board for easy wiring.
Notes:
Board address must be set for EACH
BOARD wired, see section 1.6.
Access control devices, door or gate
control, aux and alarm outputs, door and reset switches, request to exit, etc.
wiring is not shown, see section 3.5-3.8.
Gate operator data wiring is not shown, see section 3.10.
Power #33
Power #34 Power #33
Power #34
Board Power
16.5 VAC, 20 VA
Aux
Power
Tracker expansion boards connected to Wiegand 1
will activate Relay 1 in the access control system.
Main Door/Gate
Relay 0
#10 connects
ONLY to
tracker
expansion
boards
#10 connects
ONLY to
tracker
expansion
boards
• Maximum HARDwire run between tracker expansion boards is 4000 ft total, but no more than 2000 ft between any two
boards or from the access control system. See section 2.
•DO NOT use twisted pair wire with wiegand output format.
•Auxiliary terminal power transformer on access conrol system board must be connected. Otherwise, RS-232, elevator control
and wiegand inputs will not function.
•Proper grounding is required! Ground wire should be a minimum 12 AWG.
Auxiliary
Terminal
Black #13-Com
White #12-Data 1
Green #11-Data 0
NO
Com
Tracker Expansion
Board “Busy” #10
Important Wireless Note:
Wireless kits ARE NOT
wired like this. Refer to
wireless instructions with
the wireless kits when using
wireless communication.
3.3 Board Addresses 11 - 18 Communication Line HARDwiring
Set Relay 2 Jumper to Normally Open
Relay 2 Jumper
Use 6 conductor stranded with overall shield. 18- 22 gauge.
ONLY use 18gauge when wiring more than 8boards.
DO NOT connect shield to 2358-010 board common.
DO NOT use twisted pair.
Note: See
section 3.5-3.8
to wire board
options.

2358-065-L-7-16
14
NC
NO
RING
ON
CLK SEN
SPK VOL
ELEVATOR
12345 6 7891011121314
1 2 3
MIC VOL
OFF
KEYPAD
321
32
1
MASTER CODE
16AC16ACBAT
1NO1NC1C2RY2C
AZIMC
5VDCIMDSPKRCOMMICPSWCGND
O
NE
234 201918171615141312111098765
NO NC C
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Board Addresses 11 - 18 MUST connect to Relay 1/Wiegand 1 (12 Boards MAX)
Relay 1
Relay 2
Main
Terminal
Auxiliary
Terminal
Access Control System Board
Communication Lines (See section 3.3)
Zone Addresses Zone Addresses Zone Addresses Zone Addresses
Zone AddressesZone AddressesZone AddressesZone Addresses
Relay 2
Jumper
Wiegand 1
Black #13-Com
White #12-Data 1
Green #11-Data 0
Wiegand 2
Black #9-Com
White #8-Data 1
Green #7-Data 0
Brown #13 - 2C Common
Blue #14 - 2RY N.O.
Brown #15 - 1C Common
Blue #17 - 1 N.O.
Red #10 - Busy
Relay 2 Jumper
set to Normally Open
3.4 MAX Boards Communication Line HARDwiring
Tracker expansion board addresses 3-10 must be connected to Relay 2/Wiegand 2. Board addresses 11-18must be connected to Relay 1
/Wiegand 1.
Tracker Expansion Board Notes:
Terminal Connections:
Red #10 - Busy (DO NOT connect to access control system)
Blue #17 - Communication Relay
Brown #19 - Common
Black #27 - Communication Wiegand Common
White #28- Communication Wiegand Data 1
Green #29 - Communication Wiegand Data 0
•Use 6 conductor stranded with overall shield. 18- 22 gauge.
ONLY use 18gauge when wiring more than 8boards, up to
12 boards maximum.
DO NOT connect shield to 2358-010 board common.
DO NOT use twisted pair.
•Board address must be set for EACH BOARD wired,
Zone addresses MUST to be used when wiring more than
8boards per relay/wiegand input, but “Zones” can be used
when wiring more than one board to a relay/wiegand input
(See section 1.6). Board addresses can vary from this
illustration.
•Power, access control devices, door or gate control,
alarm outputs, door and reset switches, request to exit,
etc. wiring is not shown, see sections 3.5-3.8.
•Gate operator data wiring is not shown, see section 3.10.
Board Addresses 3 - 10 MUST connect to Relay 2/Wiegand 2 (12 Boards MAX)
Communication Lines (See section 3.2)
Red #10 - Busy
NC
NO
Wiegand 1 Wiegand 2
Board
Address
11
Board
Address
12
Board
Address
13
Board
Address
14
Board
Address
14
Board
Address
15
Board
Address
16
Board
Address
18
Board
Address
3
Board
Address
4
Board
Address
4
Board
Address
5
Board
Address
6
Board
Address
6
Board
Address
9
Board
Address
10
Important Wireless Note:
Wireless kits ARE NOT
wired like this. Refer to
wireless instructions with
the wireless kits when using
wireless communication.
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Board
Address
7
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Board
Address
8
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Board
Address
9
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Board
Address
9
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Board
Address
10
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Board
Address
16
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Board
Address
17
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Board
Address
17
34 33 32 31 30 29 28 27 26 25 24 23 22 21
14 15 16 17 18 19 20 13 12 11 10
9 8 7 6 5 4 3 2 1
ON
1 0
BOARDADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Board
Address
18

2358-065-L-7-16 15
34
33
32
31
30
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
13
12
11
10
9
8
7
6
5
4
3
2
1
ON
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF
SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Request to Exit
Card Reader
Wiegand Access Control Device
Terminals-#25 & #26 Output Relay Jumper
Gate Operator connects
to Terminals-#25 & #26
instead of door.
3.5 Basic Wiring Options at Access Point
Set Output Relay jumper on the tracker expansion board to N.O. (Normally Open) when using fail-secure (electric strike) locking device.
Set Output Relay jumper on the tracker expansion board to N.C. (Normally Closed) when using fail-safe (magnetic lock) locking device.
Set Output Relay jumper on the tracker expansion board to N.O. (Normally Open) when using a gate operator.
Board Address
MUST be set.
See section 1.6.
#6-Green = Data 0
#7-White = Data 1
#8-Black = Common
#9-Red = 12 VDC Power
Door Control
OROR OR
Power for
electric strike or
magnetic lock is
NOT provided
by the system.
Use separate UL
listed power
supply.
Note: Relay contact (25-26) is rated at 1A 30V maximum
and can be set for Normally Open (N.O.) or Normally
Closed (N.C.) operation.
4-6 conductor, stranded with
overall shield, 18-22 gauge.
500 ft max.
DO NOT use twisted pair.
Note: Input - #6, #7, #8, #9
will accept most wiegand
26, 30 and 31-bit access
control devices.
Two wiegand devices can
be connected in parallel to
these terminals if desired.
The access control system
will manage the two
devices connected as if
they were a single
access control device.
Magnetic lock
Output Relay:
Normally Closed (NC)
Electric strike
Output Relay:
Normally Open (NO)
Slide Gate Operator
Output Relay:
Normally Open (NO)
This shows wiring to operate the gate operator ONLY. To wire gate
operator to track and report data to the access control system,
see your specific gate operator data wiring in section 3.10.
Swing Gate Operator
Output Relay:
Normally Open (NO)
Barrier Gate Operator
Output Relay:
Normally Open (NO)
Overhead Gate Operator
Output Relay:
Normally Open (NO)
#8-Common
#20-Card Reader LED or
Beeper Control (Available
on certain card readers)
#18-Request to Exit Input
#25-Output Relay
#26-Output Relay
#33 - 16.5 VAC Power
#32 - Ground Required
#34 - 16.5 VAC Power
Gate Operator Control
Important Note: Communication line
(sections 3.2-3.4) and gate operator data
wiring (section 3.10) is NOT shown.
Board Power
16.5 VAC, 20 VA
Required
18GA. Wire 100 ft max
16 GA. Wire 200 ft max
Note: Terminals
can be removed
from board for
easy wiring.
Wire polarity
does not
matter.
EXIT
PUSH TO
Note: If card
reader has
additional
lighting for
outdoor use,
separate power
must be
provided.

2358-065-L-7-16
16
34
33
32
31
30
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
13
12
11
10
9
8
7
6
5
4
3
2
1
ON
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF
SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Local
Alarm
Separate
Alarm
Power
Alarm Reset Station
#4-White Com
#6-Blue Reset
Door Contact Switch
Integral Mode
(Programming Step 16)
Dry relay contacts connect
to existing alarm system.
Terminals-#23 & #24 Alarm Relay Jumper
Terminals-#21 & #22 Aux Relay Jumper
3.6 Alarm Wiring Options at Access Point
Board Address
MUST be set.
See section 1.6.
Note: Relay contacts (21-22; 23-24) are rated at 1A 30V
maximum and can be set for Normally Open (N.O.) or
Normally Closed (N.C.) operation.
Set Alarm Relay
jumper typically (NO).
Set Auxiliary Relay jumper typically (NO).
#8-Common
#8-Common
#21-Auxiliary Relay
#23-Alarm Relay
#24-Alarm Relay
#33 - 16.5 VAC Power
#32 - Ground Required
#34 - 16.5 VAC Power
#22-Auxiliary Relay
#16-Reset Alarm Input
#15-Door Ajar Input
Important Note: Communication line
(sections 3.2-3.4) is NOT shown.
Board Power
16.5 VAC, 20 VA
Required
18GA. Wire 100 ft max
16 GA. Wire 200 ft max
Note: Terminals
can be removed
from board for
easy wiring.
Wire polarity
does not matter.
Door
Door Frame
Door Contact Switch
Bypass Mode
(Programming Step 16)
MUST be connected to
existing alarm system.
#23-Alarm Relay #24-Alarm Relay
Door
Door Frame
Switch Closed:
Door Closed
N.C.
Com
Switch Open:
Door Open
N.C.
Magnet
SPST (NO)
SPST (NO)
Com
Switch Closed:
Door Closed
N.C.
Com
Switch Open:
Door Open
N.C.
Magnet
SPST (NO)
SPST (NO)
Com
Note: Input for door contact switch is factory set at
0 for normally Open (Circuit Open - CO) but it can
be set for normally Closed (Circuit Closed - CC) by
programming step 8, set to 1 if required.

2358-065-L-7-16 17
Switch Closed:
Door Closed
N.C.
Com
Switch Open:
Door Open
N.C.
Magnet
SPST (NO)
SPST (NO)
Com
34
33
32
31
30
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
13
12
11
10
9
8
7
6
5
4
3
2
1
ON
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF
SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Local
Alarm
Separate
Alarm
Power
Alarm Reset Station
#4-White Com
#6-Blue Reset
Request to Exit
Card Reader
Wiegand Access Control Device
Dry relay contacts connect
to existing alarm system.
Terminals-#25 & #26 Output Relay Jumper
Terminals-#23 & #24 Alarm Relay Jumper
Terminals-#21 & #22 Aux Relay Jumper
Gate Operator connects
to Terminals-#25 & #26
instead of door.
3.7 All Available Devices at Access Point
Set Output Relay jumper on the tracker expansion board to N.O. (Normally Open) when using fail-secure (electric strike) locking device.
Set Output Relay jumper on the tracker expansion board to N.C. (Normally Closed) when using fail-safe (magnetic lock) locking device.
Set Output Relay jumper on the tracker expansion board to N.O. (Normally Open) when using a gate operator.
Board Address
MUST be set.
See section 1.6.
#6-Green = Data 0
#7-White = Data 1
#8-Black = Common
#9-Red = 12 VDC Power
Door Control
OROR OR
Power for electric
strike or magnetic
lock is NOT
provided by the
system. Use
separate UL listed
power supply.
Note: Relay contacts (21-22; 23-24; 25-26) are rated at 1A
30V maximum and can be set for Normally Open (N.O.) or
Normally Closed (N.C.) operation.
4-6 conductor, stranded with
overall shield, 18-22 gauge.
500 ft max.
DO NOT use twisted pair.
Set Alarm
Relay jumper
typically (NO).
Set Auxiliary Relay
jumper typically (NO).
Magnetic lock
Output Relay:
Normally Closed (NC)
Electric strike
Output Relay:
Normally Open (NO)
Slide Gate Operator
Output Relay:
Normally Open (NO)
This shows wiring to operate the gate operator ONLY. To wire gate
operator to track and report data to the access control system,
see your specific gate operator data wiring in section 3.10.
Swing Gate Operator
Output Relay:
Normally Open (NO)
Barrier Gate Operator
Output Relay:
Normally Open (NO)
Overhead Gate Operator
Output Relay:
Normally Open (NO)
#8-Common
#8-Common
#20-Card Reader LED or
Beeper Control (Available
on certain card readers)
#18-Request to Exit Input
#21-Auxiliary Relay
#23-Alarm Relay
#24-Alarm Relay
#25-Output Relay
#26-Output Relay
#33 - 16.5 VAC Power
#32 - Ground Required
#31 - Battery Back-Up (+)
#30 - Battery Back-Up (-)
#34 - 16.5 VAC Power
#22-Auxiliary Relay
#16-Reset Alarm Input
#15-Door Ajar Input
Gate Operator Control
Important Note: Communication line
(sections 3.2-3.4) and gate operator data
wiring (section 3.10) is NOT shown.
Board Power
16.5 VAC, 20 VA
Required
18GA. Wire 100 ft max
16 GA. Wire 200 ft max
Note: Terminals
can be removed
from board for
easy wiring.
1 Board:
.8Amp/Hour
Battery
Optional
Wire polarity
does not matter.
EXIT
PUSH TO
Door
Door Frame
Door Contact Switch
Integral Mode shown
(See previous page)
Note: Input - #6, #7, #8, #9
will accept most wiegand
26, 30 and 31-bit access
control devices.
Two wiegand devices can
be connected in parallel to
these terminals if desired.
The access control system
will manage the two
devices connected as if
they were a single
access control device.
Note: If card
reader has
additional
lighting for
outdoor use,
separate power
must be
provided.

2358-065-L-7-16
18
34
33
32
31
30
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
13
12
11
10
9
8
7
6
5
4
3
2
1
ON
1
0
BOARD ADDRESS
0
9
8
7
6
5
4
3
2
1
NC
OUTPUT
RELAY
NO
NC
ALARM
RELAY
NO
NC
AUX
RELAY
NO
ENT
RESET
2358-010
RF
DATA
RF
SECURE
RF
STATUS
CODE
SENT
CODE
GOOD
CODE
BAD
Request to Exit
Card Reader
Wiegand Access Control Device
Terminals-#25 & #26 Output Relay Jumper
3.8 Typical Dual Mode Wiring at 2 Access Points
Board Address
MUST be set.
See section 1.6.
Terminals-#21 & #22 Aux Relay Jumper
#6-Green = Data 0
#7-White = Data 1
#8-Black = Common
#9-Red = 12 VDC Power
Door Control
Access Point 1Access Point 2
OR
Power for electric
strike or magnetic
lock is NOT
provided by the
system. Use
separate UL listed
power supply.
4-6 conductor, stranded with
overall shield, 18-22 gauge.
500 ft max.
DO NOT use twisted pair.
Magnetic lock
Output Relay:
Normally Closed (NC)
Electric strike
Output Relay:
Normally Open (NO)
Gate Operator
Output Relay:
Normally Open (NO).
Gate Operator connects
to Terminals-#25 & #26
instead of door.
Request to Exit Note:
No alarm functions
No door ajar functions
Power for electric
strike or magnetic
lock is NOT
provided by the
system. Use
separate UL listed
power supply.
#19-Common
#18-Request to Exit Input
#19-Common #15-Request to Exit Input for second Door
#25-Output Relay
#26-Output Relay
#21-Aux Relay
#22-Aux Relay
#33 - 16.5 VAC Power
#32 - Ground Required
#34 - 16.5 VAC Power
Gate Operator Control
Door Control
OR
Magnetic lock
Output Relay:
Normally Closed (NC)
Electric strike
Output Relay:
Normally Open (NO)
Gate Operator
Output Relay:
Normally Open (NO).
Gate Operator connects
to Terminals-#21 & #22
instead of door.
Gate Operator Control
Access Point 2
Board Address Setting Plus 1
in DKS Remote Account Manager Software
Access Point 1
Board Address Setting in DKS Remote Account Manager Software
Important Note: Communication line
(sections 3.2-3.4) and gate operator data
wiring (section 3.10) is NOT shown.
Board Power
16.5 VAC, 20 VA
Required
18GA. Wire 100 ft max
16 GA. Wire 200 ft max
Note: Terminals
can be removed
from board for
easy wiring.
Wire polarity
does not matter.
#20-Card
Reader LED or
Beeper Control
(Available
on certain card
readers)
Request to Exit
EXIT
PUSH TO
EXIT
PUSH TO
One tracker expansion board can be programmed
(step 12, set to 1) to control 2 access points. The board
address number that has been physically set on the
tracker expansion board and the NEXT sequential board
address number will control the 2 access points. When
the access device (Card Reader) gets activated from
Access point 1 and access is granted or denied, the
board will then automatically send out the same access
device information to the next sequential board address
number (Access Point 2) to grant or deny access to the
second access point. The system relays will be
identified in DKS Remote Account Manager software as
the board address setting for Access Point 1 and board
address setting plus 1 for Access point 2.
SOFTWARE
INSTALLED
Note: Input - #6, #7, #8, #9 will
accept most wiegand 26, 30 and
31-bit access control devices.
Two wiegand devices can be
connected in parallel to these
terminals if desired. The access
control system will
manage the two
devices connected
as if they were a
single access
control device.
Note: If card
reader has
additional
lighting for
outdoor use,
separate power
must be
provided.