Dorel Home Products DA4079459MK User manual

uestions, concerns, missing parts?
CONTACT OUR CUSTOMER SERVICE DEPARTMENT
BEFORE RETURNING PRODUCT TO THE RETAILER.
DA4079459MK (Light Gray Velvet)
DA4079059MK(Dark Gray Linen)
DA4079659MK (Blue Velvet)
DA4079159MK (White Velvet)
34DA4079459MK00-KT
Date of Purchase
Upholstered Daybed and Trundle
KT. - 2021/7/12
If parts are missing or damaged, we will gladly ship your
replacement parts free of charge.
Lot Number (TAKEN FROM CARTON)
Thank you for purchasing from Dorel!
THIS INSTRUCTION OOKLET CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
1
2021 Dorel Home Products All Rights Reserved
Twin
isit www.dhpfurniture.com/eng/replacement-parts
or call Toll-Free 1-800-267-1739
You can also chat with us at www.dhpfurniture.com
Weight Limit:
Daybed: 400 Lb / 181 Kg
Trundle: 250 Lb / 113 Kg

2
1-800-267-1739
DHP Consumer Services
12345 Albert Hudon, Suite 100,
Montreal, Quebec H1G 3L1
[e-mail]
● Work in a spacious area and near where the unit will be used, preferably on a
carpet, or use a piece of the cardboard packaging to protect your floor and product.
● Make sure all parts are included. Most parts are labeled or stamped on the raw
edge.
● Read each step carefully. It is very important that each step of the instructions is
performed in the correct order. If these steps are not followed in sequence,
assembly difficulties will occur.
● This product may contain small components. Please ensure that they are kept
away from small children.
● This product is designed for home use and is not intended for commercial use.
For help with assembly, identifying parts, product information or to order parts,
please contact us:
Limited 1 year Warranty
Dorel warrants this product to be free from defects in material and workmanship
and agrees to remedy any such defect. This warranty covers one year from the
date of original purchase from authorized retailers. This is solely limited to the
repair or replacement of defective parts and assembly labor is not included.
This warranty does not apply to any product which has been improperly
assembled, subjected to misuse or abuse or which has been altered or repaired in
any way.The warranty does not cover wearing, tearing, fading or splitting of the
fabric (where applicable). Liability for consequential damages is excluded to the
extent exclusion is permitted by law. This warranty gives you specific legal rights
and you may also have other rights which vary from state to state or province to
province.
To obtain warranty service, purchaser must present original bill of sale.
Components repaired or replaced are warranted through the remainder of the
original warranty period only. The defective components will be repaired or
replaced without charge, subject to the terms and conditions described above.
Visit www.dhpfurniture.com to view the limited warranty valid in the U.S. and
Canada.
Contact Us!
Read Before Beginning Assembly
Monday to Friday
Saturday
Sunday
9 am to 9 pm (Eastern Time)
10 am to 6:30 pm (Eastern Time)
11 am to 7 pm (Eastern Time)
1.5 hours
Do NOT use
powertools
This product is shipped in
1 carton(s)
Chat
with us! www.dhpfurniture.com

3
PARTS
A
O
W
E
X
Y
B
U
K
F
P
O
I
G
N
H
H
I
J
C
D
Z

4
Each part has a unique part number. Please
reference the appropriate part number when
contacting customer service for replacement
parts.
efore throwing any packaging, please
verify all contents and make sure you have
received all the parts listed above!
PARTS LIST - BOX
GK
Front Panel
1 PC
Rear Rail
1 PC
Front Rail
1 PC
E
B
Front Panel
1 PC
ackrest
1 PC
A
U
Rear Rail
1 PC
J
Front Rail
1 PC
FI
H
Center Rail
1 PC
Side Rail
2 PCS
PART NUMBERS
PART
LABELS
DA4079459MK
(Light Gray elvet)
DA4079059MK
(Dark Gray Linen)
DA4079659MK
(Blue elvet)
DA4079159MK
(White elvet)
AT1016250 T1016290 T1016340 T1016390
BT984620 T1016320 T1016370 T1016420
ET965690 T965690 T965690 T965690
FT936370 T936370 T936370 T936370
GT984650 T1016330 T1016380 T1016430
HT951010 T951010 T951010 T951010
IT926340 T926340 T926340 T926340
JT926350 T926350 T926350 T926350
KT960410 T960410 T960410 T960410
UT979520 T979520 T979520 T979520
Rear Rail
2 PCS

5
Each part has a unique part number. Please
reference the appropriate part number when
contacting customer service for replacement
parts.
efore throwing any packaging, please
verify all contents and make sure you have
received all the parts listed above!
PARTS LIST - BOX
PART NUMBERS
PART
LABELS
DA4079459MK
(Light Gray elvet)
DA4079059MK
(Dark Gray Linen)
DA4079659MK
(Blue elvet)
DA4079159MK
(White elvet)
CT1016260 T1016300 T1016350 T1016400
DT1016270 T1016310 T1016360 T1016410
T960450 T960450 T960450 T960450
WT960460 T960460 T960460 T960460
NT950950 T950950 T950950 T950950
PT950960 T950960 T950960 T950960
OT926760 T926760 T926760 T926760
XT926370 T926370 T926370 T926370
YT926380 T926380 T926380 T926380
ZT1016280 T1016280 T1016280 T1016280
O
Wooden Slats
50 PCS
racket
1 PC
W
racket
1 PC
Armrest
1 PC
DC
Armrest
1 PC
Caster
2 PCS
N
Locking Caster
2 PCS
PZ
Leg
4 PCS
Single Slat Cap
50 PCS Double Slat Cap
25 PCS
Y
X

6
Please do not completely tighten all the hardware,
until the entire assembly is complete, unless
otherwise indicated in the step-by-step instructions.
The screw(s), bolt(s) to be used at each step are
shown in actual size in the lower right corner of the
page.
HARDWARE LIST
Hardware Pack:Daybed
HP#:T4474439-00
DA4079459MK (Light Gray Velvet)
DA4079059MK(Dark Gray Linen)
DA4079659MK ( lue Velvet)
DA4079159MK (White Velvet)
1235
4
1/4" X 3/4"
olt
8 PCS
1/4" X1 3/16"
olt
20 PCS
1/4" X1 9/16"
olt
12 PCS
5/16" X2 1/4"
olt
4 PCS
4mm
Allen Key
1 PC

7
Please do not completely tighten all the hardware,
until the entire assembly is complete, unless
otherwise indicated in the step-by-step instructions.
The screw(s), bolt(s) to be used at each step are
shown in actual size in the lower right corner of the
page.
HARDWARE LIST
Hardware Pack:Trundle
HP#:T4144719LS-01
DA4079459MK (Light Gray Velvet)
DA4079059MK(Dark Gray Linen)
DA4079659MK ( lue Velvet)
DA4079159MK (White Velvet)
3
6
Wrench
1 PC
5
4mm
Allen Key
1 PC
4
1/4"
Nut
6 PCS
1/4" X1 9/16"
olt
6 PCS
2
1/4" X 3/4"
olt
8 PCS
1/4" X1 3/8"
olt
6 PCS
1

8
Step 1
Attach Z x 4 to C and D with x.
Screw v to C and D, leave half of the
thread exposed.
To avoid fraying the fabric
during assembly, please lay
the armrests C and D on a piece
of cardboard.
Do not completely tighten the
Bolts, leave half of thread
exposed.
C
D
The following instructions will illustrate how
to assemble the Daybed from Step1 to
Step7. Please use the Daybed Hardware
Pack: T4474439-00.
2
X 4
D
Z
4
4
X 8
2

9
Step 2
Attach V and W to A with u.
A
1
X 8
1
WA
W
Small holes on V & W
should be facing upward.

10
Step 3
A
D
C
Hang A on C & D as illustrated below,
don't completely tighten the OLT v until
STEP 4 is complete.
W
A
C
2

11
Step 4
X 12
F
D
C
2
C
F
E
Attach E & F & U to C and D with v .
Then properly tighten all the olts.
2
C
E
2
A
U
C
2
U
Flange of bracket on E must be located on the inside of the bed.
Slat holes on part E & F
should be facing upward.

12
Step 5
Stretch and stick the bottom edge of A
onto U as illustrated.
A
U
A

13
Step 6
.1 Attach B to E with w.
.2 Attach K to A with w.
X 12
A
B
3
A
K
3
B
E3
.1 .2
K
E
Holes on part K
should face upward.

14
Step 7
Correct : Slat curve should
be facing upwards.
Incorrect : Slat curve
facing downwards.
SLAT WARNING
Y
K
X
O
E
7.1
7.2
7.3
7.1 Insert O into X on each side as indicated;
7.2 Press X into E and K;
7.3 Insert the other free end of both O into Y
where both O meet, press Y into F
Repeat the same procedure going backwards
for every row of slats.
F
X
X
EO
OFK
XX
XX
Y
OO
OO
E
E
F
FK
K

15
Step 8
H
H
H
H
I
I
J
H
H
I
J
I
Caster holes on H
towards upward.
8.1
8.2
8.3
The following instructions will illustrate how
to assemble the Trundle from Step 8 to Step
12. Please use the Trundle Hardware Pack:
T4144719LS-01.
8.1 Lay H x 2 on the floor with holes towards
upward as illustrated.
8.2 Lay J and I x 2 with the slat holes facing
downwards.
8.3 Insert H x 2 into I x 2 and J as illustrated.
Slat holes on part I and J
towards floor as illustrated.
H

16
Step 9
Attach I x 2 & J to H x 2 with v using y
and using ❻.
X 6
H
H
J
I
I
4
2
X 6
H
J
2
4
5
6
H
I
2
4
5
6

17
Step 10
H
H
J
I
I
P
P
N
N
1
X 8
Attach P x 2 & N x 2 to H x 2 with ❶.
H
I
P
1
HJ
N
1
In order not to damage
your product, please orient lever
to the inside of the trundle as
illustrated.
Caster N should be assembled
on the side near Part J.

18
Step 11
G
I
I
J
3
Check if slat holes on I & J are
all on the top side in this STEP.
X 6
Turn over the frame assembled from
STEP10.
Attach G to J with ❸.
G
J
3

19
Step 12
O
I
J
Y
X
X
I
Correct : Slat curve should
be facing upwards.
Incorrect : Slat curve
facing downwards.
SLAT WARNING
12.1 Insert O into X on each side as indicated;
12.2 Press X into I and J;
12.3 Insert the other free end of both O into Y
where both O meet, press Y into I.
Repeat the same procedure going backwards
for every row of slats.
12.1
12.2
12.3
X
X
IO
OIJ
XX
XX
Y
OO
OO
I
I
I
IJ
J

20
Helpful Hints
To use Trundle:
Pull out the trundle completely from
underneath daybed. Once positioned, make
sure casters are locked by pushing down the
lever "ON" as illustrated "How to lock
caster!".
To store Trundle:
Unlock the casters by pushing down the
lever "OFF" as illustrated "How to unlock
caster!" and push in the Trundle underneath
the Daybed.
Keep casters in lock condition under normal
use to prevent unintentional movement
which may lead to instability and tipping.
WARNINGS:
How to lock caster? How to unlock caster?