Dorel Home Products DA6580 User manual

Thank you for purchasing from DHP!
Date of Purchase
Y.W. - 2023/02/24
Lot Number (TAKEN FROM CARTON)
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
B34DA658000-100063
1
2021 Dorel Home Products All Rights Reserved
Weight Limit : 200 Lbs / 91 Kg
DA6580 (Espresso), DA6580W (White), DA6580GR (Gray)
Loft Bed
Twin
If parts are missing or damaged, we will gladly ship your
replacement parts free of charge.
Visit www.dhpfurniture.com/eng/replacement-parts
or call Toll-Free 1-800-267-1739
You can also chat with us at www.dhpfurniture.com
DO NOT RETURN TO THE STORE !

Limited 1 year Warranty
DHP warrants this product to be free from defects in material and workmanship
and agrees to remedy any such defect. This warranty covers one year from the
date of original purchase from authorized retailers. This is solely limited to the
repair or replacement of defective parts and assembly labor is not included.
This warranty does not apply to any product which has been improperly
assembled, subjected to misuse or abuse or which has been altered or repaired
in any way.The warranty does not cover wearing, tearing, fading or splitting of
the fabric (where applicable). Liability for consequential damages is excluded to
the extent exclusion is permitted by law. This warranty gives you specific legal
rights and you may also have other rights which vary from state to state or
province to province.
To obtain warranty service, purchaser must present original bill of sale.
Components repaired or replaced are warranted through the remainder of the
original warranty period only. The defective components will be repaired or
replaced without charge, subject to the terms and conditions described above.
The terms and conditions of the limited warranty are subject to change without
notice. For the latest warranty policy, please visit www.dhpfurniture.com.
● Work in a spacious area and near where the unit will be used, preferably on a
carpet, or use a piece of the cardboard packaging to protect your floor and
product.
● Make sure all parts are included. Most parts are labeled or stamped on the raw
edge.
● Read each step carefully. It is very important that each step of the instructions is
performed in the correct order. If these steps are not followed in sequence,
assembly difficulties will occur.
● This product may contain small components. Please ensure that they are kept
away from small children.
● This product is designed for home use and is not intended for commercial use.
Contact Us!
For help with assembly, identifying parts, product information or to order parts,
please contact us: This product is shipped in
1 carton
www.dhpfurniture.com
[email protected]om
1-800-267-1739
Monday to Friday 9am to 9pm (Eastern Time)
Saturday 10 am to 6:30 pm (Eastern Time)
Sunday 11 am to 7pm (Eastern Time)
DHP Consumer Services
12345 Albert Hudon, Suite 100,
Montreal, Quebec H1G 3L1
Do NOT use
powertools
Phillips head screwdriver
needed (not included)
2
100 minute
Read Before Beginning Assembly

●STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are not designed for use with the bed; for example,
but not limited to, hooks, belts and jump ropes.
WARNINGS - Loft Bed: Twin
3
● Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed.
● The mattress platform is designed to support a mattress without the need for a posture board or box spring.
● Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood of entrapment or falls.
●USE ONLY COIL SPRING MATTRESSES ON THE UPPER BUNK. FAILURE TO DO SO CAN RESULT IN INJURY.
● Use only mattresses which are 74"-75" long and 37 1/2" - 38 1/2" wide on upper and lower bed. Ensure thickness of mattress does not exceed
6"(152mm). Surface of mattress must be at least 5"(127mm) below the upper edge of guardrails.
● Do not allow children under 6years of age to use the upper bunk.
● Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to the wall, the guardrail that runs the full length
of the bed should be placed against the wall to prevent entrapment between the bed and wall (applicable for bunk beds with full length
guardrails on one side).
● Periodically check and ensure that the guardrail, ladder and other components are in their proper position, free from damage, and that all
connectors are tight.
● Do not allow horseplay on or under the bed and prohibit jumping on the bed.
● Do not use substitute parts. Contact customer service for replacement parts.
● Use of a night light may provide added safety precaution for a child using the upper bunk.
● The use of water or sleep flotation mattresses is prohibited.
● Always use the ladder for entering and leaving the upper bunk.
● Prohibit more than one person on upper bunk.
● Keep these instructions for future reference.

4
PARTS
X
V
R
M
T
back view
W
U
J
L
C
T
K
A
D
O
Q
S
H
L
R
G
F
B
C
P
J
E
I
M
N
E

PARTS LIST
LEFT FRONT POST
1 PC
LEFT BACK POST
1 PC
RIGHT BACK POST
1 PC
RIGHT FRONT POST
1 PC
HEADBOARD CROSS
6 PCS
HEADBOARD CENTER CROSS
1 PC
HEADBOARD CENTER CROSS
1 PC
HEADBOARD PANEL
4 PCS
FRONT SIDE RAIL
1 PC
BACK SIDE RAIL
1 PC
DESK FRONT RAIL
1 PC
SLAT
13 PCS
5
A DCB
E HGF
IK JL

PARTS LIST
LONG GUARDRAIL
1 PC
SHORT GUARDRAIL
1 PC
LEFT LADDER END
1 PC
RIGHT LADDER END
1 PC
LADDER STEP
5 PCS
GUARDRAIL LEG
2 PCS SHORT GUARDRAIL POST
1 PC
DESK PANEL
1 PC
MON P
QS RT
6

PARTS LIST
DESK BACK RAIL
1 PC
BOTTOM BACK GUARDRAIL
1 PC
BOTTOM BACK SIDE RAIL
1 PC
SUPPORT POST
1 PC
SPACE BLOCK
2 PCS
7
UWV X
Y
Each part has a unique part
number. Please reference the
appropriate part number when
contacting customer service for
replacement parts.
Before throwing any packaging,
please verify all contents and
make sure you have received
all the parts listed above!

PART UNMBERS
PART
LABELS DA6580
(Espresso)
DA6580W
(White)
DA6580GR
(Gray)
AT1027420 T1027670 T1026970
BT1027430 T1027680 T1026980
CT1027440 T1027690 T1026990
DT1027450 T1027700 T1027000
ET1027460 T1027710 T1027010
FT1027470 T1027720 T1027020
GT1027480 T1027730 T1027030
HT1027490 T1027740 T1027040
IT1027500 T1027750 T1027050
JT1027510 T1027760 T1027060
KT1027520 T1027770 T1027070
LT1027530 T1027780 T1027080
MT1027540 T1027790 T1027090
NT1027550 T1027800 T1027100
OT1027560 T1027810 T1027110
PT1027570 T1027820 T1027120
QT1027580 T1027830 T1027130
RT1027590 T1027840 T1027140
ST1027600 T1027850 T1027150
TT1027610 T1027860 T1027160
UT1027620 T1027870 T1027170
VT1027630 T1027880 T1027180
WT1027640 T1027890 T1027190
XT1027650 T1027900 T1027200
YT1027660 T1027910 T1027210
8

HARDWARE LIST
Ø 1/4" x 100mm Ø 6.5mm x 48mm
JOINT CONNECTOR (4mm HEX HEAD)
12 PCS
WOOD JOINT CONNECTOR (4mm HEX HEAD)
12 PCS
Ø 6.5mm x 100mm Ø 4mm x 35mm Ø 11.8mm x 15mm
WOOD JOINT CONNECTOR (4mm HEX HEAD)
26 PCS
FLAT HEAD SCREW
10 PCS
BARREL NUT
12 PCS
Ø 4mm x 30mm Ø 10mm x 50mm
FLAT HEAD SCREW
6 PCS
WOOD DOWEL
44 PCS
ALLEN KEY
1 PC
1
876
543
2
9

HARDWARE LIST
Ø 1/4" x 64mm Ø 8mm x 30mm Ø 1/4" x 32mm
JOINT CONNECTOR (4mm HEX HEAD)
7 PCS
WOOD DOWEL
2 PCS
JOINT CONNECTOR (4mm HEX HEAD)
4 PCS
Ø 9mm x 17mm Ø 1/4" x 15mm 30mm x 30mm x 18mm Ø 3.5mm x 19mm
HEX CAP
2 PCS
JOINT CONNECTOR
(4mm HEX HEAD)
12 PCS
L SHAPED METAL PLATE
6 PCS
FLAT HEAD SCREW
2 PCS
9
10
Hardware Pack
Please do not completely tighten all the hardware,
until the entire assembly is complete, unless
otherwise indicated in the step-by-step instructions.
The screw(s), bolt(s) to be used at each step are
shown in actual size in the lower right corner of the page.
DA6580 (Espresso),
DA6580GR (Gray) HP#: TDA6580-01
DA6580W (White) HP#: TDA6580W-01
10 11
12 13 14 15