Dorel Home Products MAINSTAYS 4055019W User manual

DO NOT RETURN TO THE STORE !
Visit www.dhpfurniture.com/eng/support-home
or call Toll-Free 1-800-267-1739
4055019W
B344055019W02 - 12172 - N
Date of Purchase
Metal Bunk Bed
X.P. - 2017.05.15
If parts are missing or damaged, we will gladly ship your
replacement parts free of charge.
Lot Number
Thank you for purchasing from DHP!
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
1
© 2014 Dorel Home Products All Rights Reserved
Twin over Full
Black
Weight Limit: 200 Lb / 91 Kg for upper bed; 450 Lb / 204 Kg for lower bed.

Contact Us!
[e-mail]
DHP Consumer Services
12345 Albert Hudon, Suite 100,
Montreal, Quebec, Canada H1G 3L1
Read Before Beginning Assembly
1-800-267-1739
Monday - Friday, 9:00 am - 5:00 pm (Eastern Time)
Warranty Information
2
Caution
DHP warrants this product to be free from defects in material and workmanship and
agrees to remedy any such defect. This warranty covers one year from the date of
original purchase. This is solely limited to the repair or replacement of defective
parts and assembly labor is not included.
This warranty does not apply to any product which has been improperly assembled,
subjected to misuse or abuse or which has been altered or repaired in any way.
Liability for consequential damages is excluded to the extent exclusion is permitted
by law. This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
To obtain warranty service, purchaser must present original bill of sale. Components
repaired or replaced are warranted through the remainder of the original warranty
period only. The defective components will be repaired or replaced without charge,
subject to the terms and conditions described above.
Visit www.dhpfurniture.com to view the limited warranty valid in the U.S. and
Canada.
●Call our toll free number if you need assistance.
●Work in a spacious area and near where the unit will be used, preferably on a
carpet, or use a piece of the cardboard packaging to protect your floor and product.
●Recommended # of people needed for assembly: 2(however it is always better
to have an extra hand). Estimated assembly time is 3hours.
●Make sure all parts are included. Most parts are labeled or stamped on the raw
edge.
●Read each step carefully. It is very important that each step of the instructions is
performed in the correct order. If these steps are not followed in sequence,
assembly difficulties will occur.
●This product is designed for home use and not intended for commercial use.
●This product contains small components. Please ensure that they are kept away
from small children.
●Do not use power tools to assemble your furniture. Power tools may strip or
damage the parts.
For help with assembly, identifying parts, product information or to order parts,
please contact us:

3

4
Parts
All in 1 big box!
Before you throw the package, please use the
Check Box to identify the parts and ensure that
you have all the parts needed for the assembly.
There are inner box(es) that include components
required to complete this assembly.
Replacement Parts, Visit www.dhpfurniture.com/eng/support-home
Guardrail
T930720
X 2
Post
T930640
X 2
Post
T930650
X 1
Post
T930660
X 1
Side Rail
T947620
X 1
Side Rail
T947630
X 1
Side Rail
T947640
X 2
Brace
T947650
X 2
Guardrail
T930730
X 1
Front Guardrail
T930710
X 1
A
C
D
F
JK
H
Endcap
T919620
X 4
B
EV
A
K J
H
D
F
B
E
V
C
G
G
G

5
Parts
All in 1 big box!
Before you throw the package, please use the
Check Box to identify the parts and ensure that
you have all the parts needed for the assembly.
There are inner box(es) that include components
required to complete this assembly.
Replacement Parts, Visit www.dhpfurniture.com/eng/support-home
R S
EndGuardrail
T930780
X 1
End Guardrail
T930790
X 1
End Guardrail
T930750
X 2
End Guardrail
T930740
X 2
Center Leg
T947690
X 1
Leg
T947700
X 2
Spacer
T919490
X 21
Spacer
T919480
X 22
Plug
T392590
X 88
QW Y
Slat
T919600
X 22
Slat
T930810
X 22
Slat
T947670
X 22
Ladder
T930800
X 1
N
X
O
Z
Brace
T947680
X 2
P 1
P 2
LT
S
O
QW
R
Z
U
T
L
X
N
Y
U
P 1
P 2

6
Hardware Pack
Hardware Pack #: T4055019W-01
Please do not completely tighten all the hardware,
until the entire assembly is complete, unless
otherwise indicated in the step-by-step
instructions.
The screw(s), bolt(s) to be used at each step are
shown in actual size in the lower right corner of
the page.
1 2 345
7
8
5/16" X 3/4"
X 23
1/4" X 9/16"
X 10
1/4" X 1 3/8"
X 4
1/4" X 1 3/8"
X 8
1/4"
X 8
X 4
4mm
X 1 X 1
6

7
Step 1
Insert Xinto Nand insure them with and
only using upper holes;
Plug the post tubes with BX 4 as shown.
X 2
X 2
4
5
X
N
B
X
N
4
5

8
Step 2
Attach Vto Lwith & .
36
3
X 2X 2
6
V
V
L

9
Step 3
With second person's help, hold parts
in place until this step is complete.
Attach Vto bed end structure;
Then secure parts X& Nwith & as
illustrated.
X 2
5
4
N
N
X
X
V
5
4
X 2

10
Step 4
Insert G into E &F and fix with ;
2
X 2
2
G
G
E
F

11
Step 5
Attach Tto Uwith .
X 2
X 4
2
2
T
U

12
Step 6
Attach Uto the Siderails with .
2
2
X 2
U
Slots toward inside.
X 4

13
Step 7
Insert previously-assembled parts to Las
shown.
Then attach the siderails to the Bedends
with .
Please note that Fmust be attached
to Nas the illustration shows.
Leave upper holes unscrewed until
Step 10.
1
X 4
1
F
N
F
N
U
E
G
G
L

14
Step 8
Secure the middle structure with & .
3
X 2X 2
63
6
U
U
3
6

15
Step 9
Insert Sinto A& C;
Insert Rinto A& D.
S
R
A
C
A
D
All holes toward inside.

16
Step 10
Insert Posts into the lower bunk and secure
with as shown.
ND
1
X 4
1

17
Step 11
Attach Hto Jwith & .
H
J
X 2X 2
5
4
4 5

18
Step 12
Attach Kto Jwith & .
X 2X 2
4
5
K
J
4 5

19
Step 13
Attach the previously-assembled Guardrails
to the bed end structure with as shown.
X 11
1
1

20
14.1 Insert Ointo slots to the innermost, so
you can lever it for the other end;
14.2 When both ends of Oare in place,
snap it down to the slot;
14.3 Lock Oin place with Yas shown.
Step 14
OO
Y
O
14.1 14.2 14.3