Dorel Living DA7789 User manual

Description Model Number: UPC Code:
DA7789 0-65857-17768-8
DA7789LB 0-65857-17943-9
DA7789SET 0-65857-17835-7
Date of Purchase: _____ / _____ / _____ Lot Number:
(taken from carton)
DO NOT RETURN PRODUCT TO THE STORE. If a part is missing or damaged, contact our customer
service department. We will replace the part FREE of charge.
NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ
AND KEEP FOR FUTURE REFERENCE.
Twin Loft Bed with Desk & Shelf
Congratulations on your latest furniture purchase! Dorel Living furniture has been developed with quality,
convenience and style in mind. We trust it will provide you with many years of exceptional comfort and service.
Before beginning assembly, we encourage you to familiarize yourself with your new furniture piece by taking a
few minutes to go through this booklet. It contains important information on our warranty and care tips to keep
your furniture looking as good as new.
Customer satisfaction is important to us at Dorel Asia. Our agents are available Monday to Friday 8am to 5pm
(EST) to answer any question you may have. For faster service, always have the model number ready when
calling our toll free number 1-800-295-1980 or emailing us at [email protected] .
For more great furniture ideas, check out our website at www.dorelliving.com.
You can also keep up to date on all the latest trends by liking our Facebook page.
Twin Loft Bed
Twin Loft Bed
Twin Loft Bed
Twin Loft Bed with
Desk & Shelf

*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
ALWAYS USE THE RECOMMENDED SIZE MATTRESS OR MATTRESS SUPPORT, OR BOTH, TO
HELP PREVENT THE LIKELIHOOD OF ENTRAPMENT OR FALLS.
USE ONLY MATTRESSES WHICH ARE 74"-75" LONG AND 37 1/2" - 38 1/2" WIDE ON UPPER
AND ON LOWER BUNKS. ENSURE THICKNESS OF MATTRESS DOES NOT EXCEED 6".
SURFACE OF MATTRESS MUST BE AT LEAST 5" (127MM) BELOW THE UPPER EDGE OF
GUARDRAILS.
DO NOT ALLOW CHILDREN UNDER 6 YEARS OF AGE TO USE THE UPPER BUNK.
ALWAYS USE THE LADDER FOR ENTERING AND LEAVING THE UPPER BUNK.
DO NOT USE SUBSTITUTE PARTS. CONTACT CUSTOMER SERVICE FOR REPLACEMENT
PARTS.
USE OF A NIGHT LIGHT MAY PROVIDE ADDED SAFETY PRECAUTION FOR A CHILD USING
THE UPPER BUNK.
E-MAIL: [email protected]
WARNING
STRANGULATION HAZARD - NEVER ATTACH OR HANG ITEMS TO ANY PART OF THE BUNK
BED THAT ARE NOT DESIGNED FOR USE WITH THE BED; FOR EXAMPLE, BUT NOT LIMITED
TO HOOKS, BELTS AND JUMP ROPES.
FOLLOW THE INFORMATION ON THE WARNINGS APPEARING ON THE UPPER BUNK END
STRUCTURE AND ON THE CARTON. DO NOT REMOVE WARNING LABEL FROM BED.
PROHIBIT MORE THAN ONE PERSON ON UPPER BUNK.
KEEP THESE INSTRUCTIONS FOR FUTURE USE.
THE USE OF WATER OR SLEEP FLOTATION MATTRESSES IS PROHIBITED.
ALWAYS USE GUARDRAILS ON BOTH LONG SIDES OF THE UPPER BUNK. IF THE BUNK BED
WILL BE PLACED NEXT TO THE WALL, THE GUARDRAIL THAT RUNS THE FULL LENGTH OF
THE BED SHOULD BE PLACED AGAINST THE WALL TO PREVENT ENTRAPMENT BETWEEN THE
BED AND WALL (APPLICABLE FOR BUNK BEDS WITH FULL LENGTH GUARDRAILS ON ONE
SIDE).
PERIODICALLY CHECK AND ENSURE THAT THE GUARDRAIL, LADDER AND OTHER
COMPONENTS ARE IN THEIR PROPER POSITION, FREE FROM DAMAGE, AND THAT ALL
CONNECTORS ARE TIGHT.
DO NOT ALLOW HORSEPLAY ON OR UNDER THE BED AND PROHIBIT JUMPING ON THE
BED.
THE MATTRESS PLATFORM IS DESIGNED TO SUPPORT A MATTRESS WITHOUT THE NEED FOR
A POSTURE BOARD OR BOX SPRING.
USE ONLY COIL SPRING MATTRESSES ON BOTH THE UPPER AND LOWER BUNKS. FAILURE
TO DO SO CAN RESULT IN INJURY.
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact our
customer service representative first!
CALL 1-800-295-1980
You can also order parts by writing to the address listed below. Please include the
product model number, color and a detailed description of the part.
Customer Service Department No. 413
12345 Albert-Hudon Boulevard, Suite 100
Montreal, Quebec
Canada, H1G 3L1

*
*
*
*
*
*
*
*
WARNING: Should this product
become damaged, and/or
components are broken or
missing, DO NOT USE.
BED IS DESIGNED FOR CHILDREN RANGING FROM 6 YEARS OF AGE TO YOUNG
TEENAGERS.
Dust regularly with a soft, dry cloth. We do not recommend the use of chemical
cleaners or wax on our lacquered furniture as it may damage the finish. Keep
solvents, alcohol, nail polish and polish removers away from your hardwood furniture
surfaces.
MAINTENANCE
LIMITED WARRANTY
DOREL warrants its product to be free from defects in material and workmanship
and agrees to remedy any such defect. This warranty covers 1 year from the date
of original purchase. This warranty is valid only upon presentation of proof of
purchase. This is solely limited to the repair or replacement of defective furniture
components and no assembly labor is included. This warranty does not apply to
any product which has been improperly assembled, subjected to misuse or abuse
or which has been altered or repaired in any way. This warranty gives you specific
legal rights and you may also have other rights which vary from State to State.
CARE AND CLEANING
Check bolts/screws periodically and tighten them if necessary.
PHILLIPS SCREWDRIVER (NOT INCLUDED) IS REQUIRED.
A RUBBER MALLET (NOT INCLUDED) IS RECOMMENDED TO FACILITATE ASSEMBLY.
READ EACH STEP CAREFULLY BEFORE STARTING. IT IS VERY IMPORTANT THAT EACH STEP
OF INSTRUCTION IS PERFORMED IN THE CORRECT ORDER. IF THESE STEPS ARE NOT
FOLLOWED IN SEQUENCE, ASSEMBLY DIFFICULTIES WILL OCCUR AND CAN RESULT IN
INJURY.
CAUTION: ADULT ASSEMBLY REQUIRED
ASSEMBLY WILL REQUIRE TWO PEOPLE.
MOST BOARD PARTS ARE LABELED OR STAMPED ON THE RAW EDGE.
MAKE SURE ALL PARTS ARE INCLUDED. WORK IN SPACIOUS AREA, PREFERABLY ON A
SMOOTH SOFT SURFACE.
NOTES

HARDWARE LIST (To Assemble the Loft Bed Only)
1 2
3 4
5 6
7 8
910 11
Φ 8mm x 30mm
Φ 1/4" x 32mm
Φ 9mm x 17mm
Φ 10mm x 50mm
LARGE WOOD DOWEL
12 PCS
ALLEN KEY
1 PC
JOINT CONNECTOR (4mm HEX HEAD)
8 PCS
WOOD JOINT CONNECTOR (4mm HEX HEAD)
14 PCS
Φ 1/4" x 85mm
Φ 6.5mm x 48mm
Φ 6.5mm x 80mm
Φ 4mm x 35mm
Φ 11.8mm x 15mm
Φ 4mm x 30mm
WOOD JOINT CONNECTOR (4mm HEX HEAD)
8 PCS
FLAT HEAD SCREW
14 PCS
BARREL NUT
8 PCS
FLAT HEAD SCREW
9 PCS
32 PCS
48 PCS
2 PCS
HEX CAP
JOINT CONNECTOR (4mm HEX HEAD)
SMALL WOOD DOWEL

HARDWARE LIST (To Assemble the Desk and Shelf)
910 11
8 PCS
8 PCS
8 PCS
Φ 8mm x 30mm
Φ 1/4" x 32mm
Φ 9mm x 17mm
SMALL WOOD DOWEL
JOINT CONNECTOR (4mm HEX HEAD)
HEX CAP

PARTS LIST (Loft Bed Only)
A B C
D E F
1PC
4 PCS
1 PC
FRONT LEFT POST
1 PC
BACK LEFT POST
1 PC
BACK RIGHT POST
1 PC
FRONT RIGHT POST
HEADBOARD RAIL
LEFT TOP SHELF
A
B
C
D
J
K
L
L
L
LLL
R
R
S
E
E
E
E
F
G
H
I
M
N
OP
Q
V

PARTS LIST (Loft Bed Only)
G H I
J K L
M N O
P Q R
S V W
1 PC
LEFT BOTTOM SHELF
1 PC
RIGHT TOP SHELF
1 PC
SLAT
BACK SIDE RAIL
FRONT SIDE RAIL
1 PC
1 PC
LONG GUARDRAIL
SHORT GUARDRAIL
LEFT LADDER END
RIGHT BOTTOM SHELF
1 PC
1 PC
1PC
7 PCS
RIGHT LADDER END
LADDER STEP
GUARDRAIL LEG
1 PC
5 PCS
3 PCS
SHORT GUARDRAIL POST
BOTTOM GUARDRAIL
SPACE BLOCK
1 PC
1 PC
2 PCS

PARTS LIST (Desk and Shelf)
T U
SHELF
DESK
1 PC
1 PC
A
B
C
D
E
E
E
E
F
G
H
I
J
K
L
L
L
LLL
M
N
OP
Q
R
R
ST
UU
T
V
J
M
B
C
back view

NOTE: Do not fully tighten the joint connectors (10). This will facilitate assembly in the
following steps.
Insert small wood dowels (9) into the holes of front left post (A) and back left post (B) as
shown.
STEP 1
Insert small wood dowels (9) into the ends of left top shelf (F) and left bottom shelf (G).
Attach the shelves (F & G) to front left post (A) and back left post (B) with joint connectors
(10) and Allen key (8) as shown.

Fully tighten all joint connectors (10) previously installed.
STEP 2
Attach the headboard rails (E) to front left post (A) and back left post (B) with joint
connectors (10) and Allen key (8) as shown.
NOTE: One of the headboard rails (E) has a warning label on it. DO NOT use it in this step.
Secure shelves (F & G) to left posts (A & B) with joint connectors (10) and Allen key (8) as
shown.

NOTE: Do not fully tighten the joint connectors (10). This will facilitate assembly in the
following steps.
Insert small wood dowels (9) into the holes of back right post (C) and front right post (D) as
shown.
STEP 3
Insert small wood dowels (9) into the ends of right top shelf (H) and right bottom shelf (I).
Attach the shelves (H & I) to back right post (C) and front right post (D) with joint connectors
(10) and Allen key (8) as shown.

Fully tighten all joint connectors (10) previously installed.
STEP 4
Attach the headboard rails (E) to right posts (C & D) with joint connectors (10) and Allen key
(8) as shown.
Secure the shelves (H & I) to right posts (C & D) with joint connectors (10) and Allen key (8)
as shown.
NOTE: Use the headboard rail (E) with the warning label attached to it in this step.

Insert barrel nuts (5) into back side rail (J) and attach it to back posts (B & C) with joint connectors (1).
Attach long guardrail (M) to back posts (B & C) with wood joint connectors (3) and Allen key (8).
Skip Steps 6 & 7 and go directly to Step 8.
Insert large wood dowels (7) into ends of the bottom guardrail (V) and attach it to back posts (B & C) with
wood joint connectors (3) and Allen key (8) as shown.
STEP 5
IMPORTANT
- Skip this step if you purchased the Desk & Shelf Kit
model DA7789D.
- If you did not purchase the Desk and Shelf Kit, skip
step 6 & 7 after completing step 5.
3
5
3
C
M
J
5
1
3
8
5
B
A
EE
MJ
C
D
EE
3
1

Insert barrel nuts (5) into left end of back side rail (J) and attach it to left back post(B) with joint
connectors (1).
Attach long guardrail (M) to left back posts (B) with wood joint connectors (3) and Allen key(8).
Insert large wood dowel (7) into left end of the bottom guardrail (V) and attach it to left back post(B) with
wood joint connector (3) and Allen key (8) as shown.
STEP 6
Insert small wood dowels (9) into left end of shelf (T) and desk (U) and attach them to shelves (F & G) with
hex caps (11), joint connectors (10) and Allen key (8) as shown.
B
A
M
EE
G
F
1
3
3
8
5
3B
B
U
V
F9
9
10
11
9
9
7
10
10
11
11
9
911
7

Insert small wood dowels (9) into the other end of shelf (T ) and desk (U) and attach them to shelves (H &
I) with hex caps (11), joint connectors (10) and Allen key (8).
Insert barrel nuts (5) into the other end of back side rail (J) and attach it to right back post (C) with joint
connectors (1).
Attach long guardrail (M) to right back posts (C ) with wood joint connectors (3) and Allen key (8).
Insert large wood dowel (7) into the other end of bottom guardrail (V) and attach it to right back post (C)
with wood joint connector (3) and Allen key (8).
STEP 7
B
AC
D
MJ
EE
5
3
1
11 9
9C
H
T
5
U
T
H
I
7
9
9
3
10
11
8
C
M
J

Insert barrel nut (5) into front side rail (K), Attach front side rail (K) to front left post (A) and
front right post (D) with joint connectors (1) and Allen key (8) as shown.
STEP 8
With the help of another person, turn the unit up right.
NOTE- the illustrations in Step 8 -14 will not
show the desk (U) and shelf (T) for clarity.
1
1
8
A
K
E
E
5
1
K
A
D
E
E

Attach short guardrail (N) to front left post (A) with wood joint connectors (3).
Secure short guardrail post (S) to front side rail (K) with joint connectors (10), hex cap (11) and
Allen key (8) as shown.
STEP 9
Attach short guardrail post (S) to short guardrail (N) with joint connectors (10) and Allen key (8).
N
10
8
10
A
K
N
E
E
3
3

Attach the front side rail (K) to front posts (A & D) with joint connectors (10) and Allen key
(8) as shown.
STEP 10
Secure the back side rail (J) to back posts (B & C) with joint connectors (10) and Allen key
(8) as shown.
A
K
J
A
D
C
B
10
810
J
C
10
K
A
10
D
K

STEP 11
Insert large wood dowels (7) into the ends of the ladder steps (Q).
Attach left ladder end (O) and right ladder end (P) to ladder steps (Q) with wood joint
connectors (2) and Allen key (8) as shown.

STEP 12
Attach the right ladder end (P) to the front right post (D) with wood joint connectors (2)
and Allen key (8).
Attach the ladder to the front side rail (K) with wood joint connectors (2) and Allen key (8).
D
K
82
2O
P
2
2
D
K
282