Dosch&Amand DA1275 User manual

-1-
DA1275 DECT Repeater
Manual
page
3 Start-Up with DSL Router
4 Activating Multicell Mode
5 Operational Place of Repeater
6 Start-up with DECT GAP Basisstation
7 Start Configuration
8 Cascading
9 ex-works-setting (Reset)
Connectors, LED, USB, Button
10 Software Upgrade
Question and Answers (FAQ), Registration via PC APP
11 Security Advices
12 Warranty
13 Recycling
14 CE Conformity

-2-
Congratulations
You have choosen an innovative DECT Repeater: DA1275
In order to extend the DECT range of DSL Router – e.g. Speedport of
T-COM – a new Repeater technology has been developed.
This technology has been derived from professional Multicell Networks
and got the name SATELLITE Mode (SAT Mode). Applying SAT Mode to
your DECT interface of your DSL-Router you can double the range with
full encryption.
DA1275 can be used in traditional DECT REPEATER Mode (REP Mode)
for all Standard DECT GAP Base.
In case of REP Mode directly go to page 6
We wish you best DECT radio receiption at any place in your home !

-3-
Start-Up with DSL-Router (SAT Mode)
(Deutsche Telekom Speedport, TP-Link Router, Internet Box,…)
1. place and switch-on DA1275 and Handsets near Router
2. press „Registration“ at Router …..
wait till LED3 is flashing (see p.9 LED)
System PIN Basis „0000“ otherwise see p.10
3. register DECT Handset (see Manual Handset)
Handset is correctly registered
otherwise goto Pos 2 and repeat
4. switch OFF Handset
READY
goto step2 in case more DECT Handsets shall be registered

-4-
Activating Multicell Mode
Goto next page in case you do not register a Gigaset Handset
1. Activate „Subscription Mode“ of DA1275 Repeater
Press 3 times Side Key in short intervals
LED2 : yellow flash
2. Subscribe DECT-Handset
(see Manual Handset: „Registration to Base“)
Important: choose next free Base
Hint: System Code „0000“
3. DA1275 will return to operational mode
4. choose in Menu DECT Handset „Best Base“
5. switch OFF Handset
READY
If Handset does not support multiple subscriptions
(Base1, Base2,…), this Handset is not suitable

-5-
Operational Place of Repeater
be sure to have your DECT-Handsets with you
For best selection of operational place follow below rules a-c
a divide in half the distance between DECT handset and DECT base
b distance of Repeater to Base shall not be smaller than 10 Meter
c LED2 green
After DA1275 has been setup, sequentially switch ON handsets
You have installed encrypted range extension for your DSL Router
Now you can place your Handsets anywhere in your home. The Handsets
will automatically select the suitable radio cell.
Please consider that only 2 Handsets can be simultaneously used in
Repeater cell.

-6-
Start-Up with DECT Base (REP Mode)
(commercially available DECT GAP Base Station)
1. switch-on DA1275 near Base Station
2. switch-on Repeater Mode of DECT Base Station
(see Manual of DECT Base Station)
3. press „Registration“ at DECT Base Station
4. wait till DA1275 is in operational mode
Ready
take DA1275 to operational place of Repeater

-7-
Star Configuration in REP Mode
Up to 5 Repeater can be configured in a star around the DECT Base.
Follow chapter „SET-UP with
DECT Base Station“ and set
sequentially all DA1275
Repeater in operation. Please
assure that all Repeaters are
close together at DECT Base and
switched-on during the whole
process.
After registration place the Repeaters at their individual operational place
and assure that the DECT Link quality (LED2 green) of each Repeater
with respect to the Base station.
In case a single Repeater must be exchanged, all other Repeaters must
be taken back to the Base Station and switched on, prior to start the
registration of the new Repeater.

-8-
Cascading in REP Mode
Max 2 Repeater can be cascaded. The configuration as Cascade or Star
is done automatically.
DA1275 is analysing
the DECT radio link
and in case the link
quality to the Base is
insufficient, the Repeater establish a cascade to the neighbouring
Repeater.
If you change the operational position of Repeater, the configuration can
be automatically changed as cascade or star.
Follow chapter „SET-UP with DECT Base Station“ and set sequentially
all DA1275 Repeater in operation. After registration place the
Repeaters at their individual operational place
Cascades are not always supported by DECT Base
Stations (hop=0). Contact the manufacturer of the DECT Base to get
more informations.

-9-
ex-works-setting (RESET)
Press Side Key for 5 seconds to activate the RESET function of the
product. All settings are reset to ex-works conditions
After RESET the DA1275 Repeater is automatically
starting the SEARCH Mode for DECT Base Station.
Connectors, LED, side key
Nr
Element
1
LED1
power supply
(on
/
off
)
2
LED2 DECT Link Quality
(3
colors
)
3
LED3
active call in REP
(on/off
)
4
s
ide key
(Reset
,
special for multicall HS
)
5
USB
connector
(SW Upgrade)

-10-
Software Upgrade
Software Upgrades dor DA1275 can be downloaded via USB connector
and USB cablee to PC. Please search your Supplier’s website to get
informations about such Software Upgrades
FAQ Questions and Answers
Please contact the respective Websites of manufacturer and/or
Supplier. Here you can find Technical Support and FAQs.
Registration via PC APP
In case System Code (=DECT PIN) of Base Station is not “0000”, you
must use the Product PC APP for registration to Base.
You can download this PC APP including instructions from Internet
www.da-products.de/products/repeater/da1275-dect-repeater or
from Produkt Internet Support page of your Dealer.

-11-
Security Advices
Make sure your DA1275 ist not exposed to heat and interference from
electrical devices e.g. motors and transformers.
DA1275 shall be not be placed close to metallic walls.
Place DA1275 in wall sockets only with LEDs on top.
Protect your DA1275 from wet conditions, dust and agressive liquids
and acride fumes.
Use soft and wet wipes for cleaning the product. Never use
detergents.
Only qualified and authorised service personal are allowed to opend
and repair the product.
If you hand the product to further person, do not forget to hand this
manual with the product

-12-
Warranty
Your dealer warrants for 2 years for material and manufacturinq
quality of the product. Appointed date is the date of Buyer‘s receipt.
The Buyer has the right for repair or replacement.
Returned and replaced products will pass its property to the Seller. In
case of defects Buyer has to immediately inform the Seller about such
defects.
Warranty claims must be made evident via original receipt.
Any defect caused by incorrect handling, usage and caused by
physical stress or other incorrect environmental conditions are not
subject to warranty claims.

-13-
Recycling
Please contact your Seller regarding Recycling of your
product. In no case get disposed of your product via
household garbage
Manual for DA1275 DECT Repeater
English Verson 2.0 Edition 01
January 2017
Editor
DOSCH&AMAND Products GmbH München

-14-
CE Konformität
This product fulfills the requiremenzts of EU rules 2004/108/EG
(Richtlinie des Europäischen Parlaments und des Rates zur Angleichung
der Rechtsvorschriften der Mitgliedstaaten über die elektromagnetische
Verträglichkeit und zur Aufhebung der Richtlinie 89/336/EWG), and
2006/95/EG (Richtlinie des Europäischen Parlaments und des Rates zur
Angleichung der Rechtsvorschriften der Mitgliedstaaten betreffend
elektrische Betriebsmittel zur Verwendung innerhalb bestimmter
Spannungsgrenzen). The conformity with a.m. rules is confirmed by the
CE sign. The CE Conformity Declaration and Manufacturer’s Declaratiion
can be viewed under following adresse :
DOSCH&AMAND Products GmbH, Neumarkterstr. 18, 81673 München
Technical Support
More technical support can be supplied via Service Number of your Dealer
Please consult the Dealer’s website for respective Tel Number.