Doss Traveler User manual

Outdoor Waterproof Bluetooth Speaker
Mode No.: DOSS Traveler
User Manual

II. Package content
III. Product overview
• Outdoor waterproof speaker x 1
• USB charging cable x 1
• Φ3.5mm auxiliary cable x 1
• Handle belt x 2
• User manual x 1
1.
2.Mode indicator: Different lights indicate different modes.
Press 3 seconds to turn the device on or off.
3.Mode switch: Short press to toggle play mode among Bluetooth,
5. Play/Pause:
•In Bluetooth mode, press to play/pause your tune. Press for 3
seconds to disconnect with your device.
•In TF mode, press to play/pause your tune.
6. Volume/Track control:
4. Light mode: Short press to switch four different lights. Low brightness,
Medium brightness, High brightness, SOS(emergency signal).
132 456
In Bluetooth mode, press to answer or end a call. Press for 3
seconds to reject a call.
•
Thank you for your purchase of DOSS Traveler Portable Wireless
Bluetooth Speaker with bluetooth & waterproof funcon. We encourage
you to read this instrucon guide thoroughly to get the most out of this
innovave wireless portable speaker.
+Long press: Skip next Short press:Volume up.
Long press: Skip previous Short press:Volume down.

Status indicators
7. Auxiliary Φ3.5mm jack : Use it for cabled playback with compable
devices.
11. TF card: Use it for TF card (with music) playback.
9. Charging port: Plug the supplied USB cable into this port to recharge
8. LED charging indicator.
• Charging : Steady Red.
• Fully charged : Light Off
10. Reset mode: Reset speaker when it can't work.
Mode indicator
indicator
Flashing blue
Steady blue
Steady red
Light Off
Indicates that the speaker
has entered into pairing
mode and is ready to be
paired.
Indicates that the device is
successfully paired
Steady red
Steady Green
Indicates that the device has
switched to the auxiliary
input mode
Indicates that the device has
switched to the TF mode
Reset
7 8 9 10 11

V. Pairing the wireless speaker with your smart device
VI. Answering and ending a call using your speaker or
mobile phone
• Use the supplied USB cable to charge your portable speaker directly
from your computer or device with a micro USB port.
•Make sure that the speaker is fully charged before using it for the
capacity, the LED will off
3 seconds.
the device.
1. Place your smart device and wireless speaker no more than 3 feet
away from each other.
several
seconds to turn it on.
3. Set your smart device to “discover” the wireless speaker. Once
powered on, a tone will be heard and a blue LED will start flashing.
Following aer will be a prompt noficaon that the speaker has
entered into pairing mode.
4. Enable Bluetooth on your device and choose DOSS Traveler from
the list.
5. If pairing is successful, the LED will change to a steady blue and your
phone will confirm that the connecon has been established. If the
pairing process fails aer 60 seconds, please repeat the above steps
1 through 5.
1. When there is an incoming call, the speaker will generate a tone and
Briefly press the buon to pick up, long press to reject. You may
also press the answer buon on your phone to take the call using the
speaker.
2.
•

several
•
•
•
Using it with your Amazon Echo Dot
1.
Switch the DOSS Traveler speaker to Bluetooth mode,you can press
the ‘play/pause’ buon for 3 seconds to keep it in pairing status.
2.
3. Speak with a clear voice right into the built-in microphone located on
4.
5. If a call was received while you were listening to music, playback will
resume automacally once the call has ended.
To end a call, tap the buon once again. You may also end
the call directly via your cell phone.
Waterproof, Shockproof, Dust-proof rated IPX66 for 100% protecon
against water and dust. Rubberized rugged exterior for ulmate
impact resistance. Water-resistant HD loudspeaker with splash-proof
surface to increase mobility and usability for everyday indoor or
outdoor use such as at the beach, pool, boat, car, office, and more!
2.
1.
VII. Features
Modes: Low, medium, and high brightness; SOS (emergency signal)
You can connect the Amazon Echo Dot with the speaker via 3.5 mm
Aux-in cable or via Bluetooth. Here are the steps to connect via
Bluetooth:
Download the Amazon Alexa App, follow the standard setup
procedure to get the Echo dot connected to your home Wi-Fi.
3. Quick ps on how to use the handle belts:
Undo the two nuts counter-clockwise on the strap.
Remove the nuts from the straps, then put the strap through the strap
buckle.
Tighten the screw clockwise on the strap.
10.6 in
65.0 in

Product type: Outdoor Waterproof Bluetooth Speaker
Output power: 10W x 2
Driver unit: 1.7 inch speaker x 2 + 2.6 inch passive radiator
Frequency response: 65Hz-18kHz
Unit weight: 600 g
Unit dimension: 6.50x 4.45 x 2.24 inch
Warranty: One-year limited
VIII. Power
X. Warning
IX.Wireless/Networking
• Input:5V 2A
Bluetooth versions
• Profiles supported
• Do NOT disassemble, repair or modify the Bluetooth speaker by yourself.
• Do NOT use cleaning products that contain benzene, solvents or alcohol.
• Do NOT place heavy objects on top of the Bluetooth speaker.
• Do NOT use near a microwave oven or wireless LAN products.
Signal to noise rao: 50dB
7.4
Run the Alexa app, tap ‘Connue’ and Select Bluetooth .3.
4. The DOSS Traveler speaker should appear in the list of Bluetooth
devices. If not, please press the "Play/Pause" buon for 3 seconds and
try again. If it did appear, please choose DOSS Traveler to complete the
pairing process.
NOTE: Your voice command cannot turn on/off the DOSS Traveler no
maer you are connected via Bluetooth or Aux-in cable. It can only
transfer sound signals.

Bluetooth
Problem Soluon
TF Card
other
Cannot Pair with Bluetooth
devices
Press Play/Pause buon for 3
seconds,then have a try to pair it
again.
Cannot play music aer pairing Please select 'DOSS Traveler ' as the
default playback device.
The song cuts off during
playback
Please check if the Bluetooth distance
is more than 33 feet or the baery
level is low.
There is noise during playback
Laptop prompts to install driver This driver is not special for DOSS
Traveler, it's for your laptop
Bluetooth funcon, please contact
the computer company or windows
Not paired with transmier
The speaker do not play when
the card is inserted,and jump
directly back to Bluetooth
mode.
Check whether the card format is FAT
or FAT32. If not, format it to FAT or
FAT32.
Check the song format. The speaker
only supports MP3, WAV, WMV.
The song cuts off during
playback.
Customer Service Email [email protected]
Use the needle or wire to poke the
reset port
There may be a problem with the
song's file, try deleng all the songs in
the same file.
Please press Play/ Pause buon
for 3 seconds or contact with the
transmier' s customer service
for help
Trouble Shoong:
Could be caused by interference of
charging. Try to put device in a
different locaon and do not charge
it during playback.
Cannot turn off the speaker

Wonders Technology Co.,Ltd
Email:[e-mail]
Website:www.dossaudio.com
Follow us on Facebook: