Doufit ST- 01 User manual
ST-01 Stepper
In uction Manualstr
* Please read the instruction manual carefully and follow it.
* Please keep the instruction manual for your later use.
* If you want to give this product to your friends, don't forget to bring them
the instruction manual.
!
7
Service:
If you have any question or problem of our product, please contact us.
We will try our best to solve it for you.
Our Website: www.doufit.net
1 6
Precautions:
The main frame x1
Plum knob x1
Flexible knob x1
Monitor x1
Resistance bands x 2
Pull pin x1
Spare Parts Details:
* The maximum load bearing is 110Kg (242Lbs).
* If you feel unwell during using the product, please stop using it immediately
and consult your doctor for instructions before next use.
* It is recommend to take a rest after 30 minutes exercise, which is better for
your health and can extend the service life of the stepper.
* Don’t use the product immediately after diet or drinking, you need to wait
for at least 1 hour.
* Please place the product on a flat place to avoid falling.
* Please wear suitable clothes during exercise.
* Once you fold the product, please place it horizontally to avoid damage
caused by crash.
* Don’t use alkaline detergents, diluting solvents, and volatile oils to clean
products.
Thanks for purchasing Doufit ST-01 Stepper and hope you will enjoy it.
Please read the instruction manual carefully before using. And make sure
that the product is complete and free from any damage caused during
transportation.
Button functions
Details of Monitor
Parameters
The button is used to turn on, select function and clear all data.
TIME 00:00- 99:59
COUNT 0- 9999 STEP
CAL(CALORIES) 0- 9999 KCAL
STEP/MIN 0- 9999 STEP/MIN
Operation guidance
Turn on/off
The monitor will automatically turn on when you start to exercise,
and you can also turn on it manually by pressing the button.
The monitor will automatically turn off after a while when you stop
exercise.
If there is no data showing, please change the battery.
(Open the monitor and change a LR44 battery into the battery holder.)
Reset
If you long press the button over 3 seconds, all data will be reset.
If you re-install the battery, all data will be reset.
Scan
When “SCAN” in the lower left corner of the screen stop flashing, the data
will automatically switch one by one; And you can also scan each data by
pressing the button.
r
Maintenance:
*You can use the neutral dete gent diluted with water to clean the product.
*After cleaning, please wipe with dry cloth to avoid rusting.
Keep it in a clean and well-ventilated place, and avoid high temperature,
humidity or direct sunlight.
*
*
After placed for a period of time, if you want to use it again, please ensure
*When the lubricant in the pedal pipe is dry, the stepper will make loud
squeaking noise. So you should add some WD-40 in the pipe of pedals
regularly. The noise will be effectively reduced.
that the product can be used normally first, and read the precautions again.
Please unscrew the yellow pipe covers with a M5 Allen wrench, and then add
some WD-40 into the crack of pipes (both sides).
Tilt the pipe to infiltrate the lubricant in the pipe.
Wipe away excess lubricant and screw the cover back.
Finally, pedal it several times to scatter the lubricant.
5 2
Assembly Steps:
Step 2
Straighten the handle and twist the plum knob in hole 2.
Step 3
Press down pedals. Adjust the adjustable knob to adjust the stride of pedals.
Step 4
Stretch the lever to the suitable height and twist the flexible knob in hole 3.
Step 1
Unfold the frame and stand it up, then insert the pull pin in hole 1.
Hole 2
Hole 3
For the assembly video, please visit:
www.youtube.com/channel/UCorBKk34KZgI96OyGSkjF
Hole 1
DW-40
Step 5
Fold the frame for storage.
3
4
Step 5
Install the monitor on the right pedal arm.
(If the monitor is not stable, you can install the bottom cover first,
and then cover the monitor. )
*If the battery is low, please open the monitor covers and change
a LR44 battery into the battery holder.
Step 1
Unscrew the plum knob and the flexible knob.
Folding Steps:
Step 6
Tie two resistance bands on the front foot tube.
Step 2
Adjust the angle of pedals to the level as shown.
Step 3
Back the handle and the lever.
Step 4
Pull the pull pin out from hole 1.
Step 2
Step 1
Step 3
Step 4
