DOUGHXPRESS DX Series User manual

OPERATOR'S MANUAL
DX SERIES
dough Xpress.
DXA, DXE, DXM Single Heat Dough Presses
HIX
9
CORPORATION COMMERCIAL FOOO OIVISON
DXA-5S
DXE-5S
For CustomerService:
Call 1-800-835-0606 or Visit hixcorp.com
#11-- ~CORPORATION

Receiving & Setup ........................ 3
Power .................................. 4
Users Adjustable Settings ................. 5
Machine Presets ......................... 6
Pressing Dough. ......................... 7
Handle BracketPosition. .................. 9
lnterchangleable Platens . . . . . . . . . . . . . . . . . 10
FAQs .................................. 11
Leveling Instructions .................... 12
Troubleshooting ........................ 14
Cleaning & Maintenance. ................. 15
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Warranty. .............................. 22
iNl~ CDRPDRATIDN
lntertek lntertek

PLATEN SURFACE
Slight surface imperfections are a normal part of the aluminum casting process for the platens on
your press. These are not considered a defect and do not affect the funcitonality of the machine
in any way.
SHIPPING OR RETURNS
*NOTE* Save all of your shipping/packing material. Do not risk costly shipping damage, ship
only in original box.
1. Fasten machine to plywood shipping base with bolts provided.
2. Tie or tape handle securely to base.
3. Place in original box, and put side liner and top liner in place. Fold flaps and seal the box.
(Additional bottom boards, box and liners may be obtained from your supplier for a normal
cost.)
UNPACKING
Remember to save all packing material -including box, liner and board. You may need these
for shipping your machine or if a repair is necessary in the future.
INSPECTION
Inspect your machine for hidden shipping damage. Contact the delivery company immediately,
should you find damage.
INSTALLATION
1. Lift press from skid and place on cart, if you purchased one with the press. Align legs with
holes on top of cart and bolts (supplied) fasten to cart. You will need a 9/16 wrench.
CAUTION: Heavy lifting can cause injury. We recomment two person lifting or use of a mechanical
aid when handling this press. Remember to always maintain natural curves of back and bend knees
to lift.
2. Plug the cord of the press into a correctly grounded electrical outlet. The correct voltage is
indicated on the identification tag of the press.
NOTE: Upon receiving your new equipment, some debris or residue may be present on the
aluminum platen(s). Clean the platens per the instructions provided prior to first use.
3. Remove wrap from handle and platens
WARNING: Do not use an extension cord to supply power to your press.
This machine is designed in accordance with the NSF-8 sanitations standard to be sealed to the
countertop to prevent the harborage of vermin and the accumulation of dirt and debris. To coply with
this standard the end customer must seal around the perimeter of the base of the machine to the
countertop with a food grade RTV silicone sealant that is certified to the NSF/ANSI 51 standard such
as Dow Corning #732 Multipurpose Sealant.
3

TURNING THE POWER "ON"
4
1. Once the machine is plugged into power, the display will show a "Red Icon" as shown
below. To turn the power on to the machine, simply press the Red Icon.
2. The display will then come on and look similar to what is shown below.
To turn the Power "OFF" to the machine, simply press the Green "Power" Icon in the upper
right corner of the display and the machine will turn "OFF."
Q
dough Xpr·ess
<!)
O~~ Of (y)~
00:10
(y)~
MIN:SEC
(y)~
0000
RESET
COUNTER
To adjust the temperature or time settings, simply press the "UP" or "DOWN" arrows to
change the values.
As the temperature is warming up from a cold start, the temperature digits will be RED
when the heat platen temperature is more than 10 degrees away from desired set point
temperature.
When the platen temperature is less than 10 degrees, but more than 5 degrees from the
desired set point the temperature displayed will be YELLOW.
When the platen temperature displayed is within 5 degrees of the desired set point, the
temperature digits will be GREEN.
When the actual platen temperature reaches the set point, the controller will BEEP.
3. A little "Red Dot" shown above in the lower left corner of the temperature display window
represents the "Heat Light." This indicator will be on when the controller is applying power
to the heating element. It is normal for this indicator to flash on and off as heat is required.

USER ADJUSTABLE SETTINGS
Pressing the "GEAR" Icon m in the upper left corner of the Home Screen will switch the
screen to the user settings menu, shown below.
+J II
USER SETTINGS
SHUTDOWN TIMEOUT
11 PRESET QUANTITY
TIME SCALE TEMPERATURE MODE
BUZZER ON/OFF
Pressing the "BackArrow" Icon in the upper left corner of the display will take you to the previ-
ous screen.
Pressing the "Home" Icon in the upper right corner of the display will take you to the "HOME"
Screen.
Pressing any of the USER SETTINGS buttons will take you to one of the screens shown below
where you can adjust the machine settings to your preferences.
SHUTDOWN TIMEOUT
OFF
03:00
HR:MIN
CHANGE
Ill
T A I
TIME SCALE
MIN:SEC
~
Once you have made the desired adjustments, press the "BackArrow" or "Home" Icon.
Any changes in any of the settings or values you have made will be automatically stored as
you leave that screen.
5

PRESETS FOR TIME & TEMPERATURE SETTINGS
The controller has several Time and Temperature Preset options (No Presets, Two Presets,
Four Presets, Toggle Two Presets) which are selectable in the "UserAdjustable Settings" as
outlined on the previous page.
ON THE HOME SCREEN
If one of the buttons is "GREEN" then that button is the ACTIVE time and temperature preset
on the controller. See below:
2 presets option 4 presets option
If you wish to make an adjustment to the time or temperature, simply press the UP/DOWN
arrows next to the Time or Temperature values to change the number to the new setting
desired.
NOTE: You will notice when you change either the Time or the Temperature away from the preset
values, all the preset buttons will turn "Gray."
6
To store the new Time or Temperature value(s) in a preset button location, simply press and
HOLD on the desired preset button for 2 seconds. Once the new values are stored, the button
will turn GREEN and the controller will BEEP to acknowledge the new values are stored.
To "recall" a preset, simply touch on the desired preset button and the Time and Temperature
setting stored in that location will be recalled and displayed in the Time and Temperature
values.

PRESSING DOUGH
Your dough press is designed for easy use and operation to reliably press dough balls. Thickness,
shape, and size are directly related to your dough ball, its shape, the temperature of the dough, the
recipe of your dough, the type of lubricating food oil, as well as the settings of your machine. You
should experiment with the following for the results you want.
CAUTION: Excessive pressure can cause structural damage, voiding the machine warranty!
1. Touch the power button located on the front of the control panel.
2. Set the desired temperature on the time/temperature control panel as instructed in this
manual. Generally 110°-130°F for room temperature dough and 140°-150°F when using
refrigerated dough. When the actual platen temperature reaches the set point, the controller
will BEEP.
WARNING: Never attempt to press frozen dough. Personal injury and damage to your
machine could result!
NOTE: This symbol represents "Hot Surfaces" &
3. With the press in the open position, adjust the press to the desired thickness by turning the
thickness control knob located at the top of the press. Thickness is reduced by turning the
knob clockwise. Thickness is increased by turning it counterclockwise.
NOTE: The numerical thickness setting are for reference only and have no specific value to the
thickness of a pressed or finished product.
NOTE: Adjustments may be required from one product to another and will vary to achieve the
desired result.
WARNING: Make all adjustments while press is open. Adjusting the thickness while under pressure
will result in damage to the press.
Thickness
knob
7

4. Lightly lubricate the lower platen with olive oil, food/cooking oil or other food release
lubricant when pressing pizza dough. Place corn tortilla dough balls between sheets of
parchment paper.
TIP: Dough balls at room temperature give you the best results.
5. Place your dough ball in the center of the lower platen and add a small amount of your food
lubricant to the top of the dough ball. Do not add flour or dust with flour.
6. On the DXM press, pull down the handle all they way, applying pressure, until it stops.
7. After the designated time has elapsed (generally, 3-10 seconds for room temperature
dough) raise the handle all the way up to the open position.
CAUTION: Excessive pressure can cause structural damage, voiding the machine warranty!
8
8. Remove your flatened dough and place on a screen or pan with the top side face down.
You are now ready for final shaping, edging, and toppings. Tortillas can be moved to a
tortilla warmer or skillet for finishing.
9. Move on/off switch to "OFF" when finished using the press for the day. This will turn the
power off to the entire machine.
6" 5-8 OZ.
8" 6-10 OZ.
10" 8-12 OZ.
12" 16-18 OZ.
14" 18-20 OZ.
16" 20-22 OZ.
18" 22-24 OZ.
DOUGH SHRINKAGE
Ways of Overcoming this Problem:
1. Recipe -What is the percentage ofwater content in the dough? What is the percentage of oil content in
the dough?
2. Mixing -Mixing procedure, such as water temperature and mixing speed.
3. Dough Preparation -What is the time between mixing and pressing? How is the dough being stored?
4. Pressing -What is the temperature of the dough when pressing? What is the temperature of the press
when pressing? How long is the dough being pressed?

The handle bracket will be in shipping position when received. In order to use the handle bracket to
swing the lower platen receiver, you will need to position the handle bracket for use.
1. Remove (1) bolt and lock washer completely.
1
2
2. Loosen (2) bolt only enough to allow the bracket to pivot.
3. Slide the handle bracket to the left, so that the holes line up. Replace (2) bolt and lock
washer and tighten.
9

10
1. Remove the 18' flat platen that came with the press by rotating lower platen
counterclockwise and then lifting up. If you purchased the DXP-PR Platen Rack, pace the
unused platen on one of the tiers.
2. Place the different sized platen on the press by lining up the bolts with the holes on the
press.
.......
3. Once the platen is settin on top of the lower platen reciever, you will turn the platen
clockwise until you hear and feel the "click" of the spring clips (you will need to use a bit of
force to do so).

PIZZA DOUGH
Q: Why won't my dough press to size?
• Weight of the dough ball -not enough dough
• Temperature of the dough ball might be cold -higher temp/longer press time
• Set to thick -change thickness setting
Q: When I press my dough it gets sticky? Why?
• Very wet dough -turn up temperature
• Platens are not clean -possible flour build up
Q: Why won't my dough press out even?
• Unlevel platens
Q: Why is my dough tearing when I press?
• Usually this is caused by under mixing the dough in the mixer -mix on slow speed for a minimum of 10 minutes
• Cold or frozen particles in the dough
Q: What temperature should I be pressing the dough?
• Cold dough could vary from 130°F to 170°F
• Warm dough or room temperature dough 100°-110°F
Q: How long should I be pressing the dough?
• Warm dough 2-7 seconds
• Cold dough 5-10 seconds
Q: Will the heat kill the yeast?
• NO -yeast dies at 180°F for 2-minutes -The temperature we are pressing could range from 100°-170°F for a maximum
pressing time of 10 seconds. This will not affect the yeast in the dough.
Q: Is 18" the only size crust I can get with this press?
• No -The weight of the dough ball and your thick & thin setting will determine the size of your crust. Different dough ball
weights will determine the size of your crust.
Q: How do I get an edge with the press?
• Press out dough normally -(2) ways you can get an edge...
a. After pressing crust, form edge by hand
b. When saucing crust leave a 1/4" to 1/2" ring from the edge to let your oven bake the edge naturally for a nice
handmade look.
11

TOOLS REQUIRED
• 5/16" Hex Wrench
• 3/8" Socket Drive Ratchet
• 5/8" Socket, Flat Blade Screwdriver
12
1. Remove the existing four hole plugs using a flat blade screw driver. Be careful not to
scratch the surface of the platen mount during plug removal. The caps will be reinstalled
after the leveling adjustment is complete.
2. Lower the Top Platen until one side touches to determine which side will be adjusted. In the
picture below, the front of the platen could be raised or the back could be lowered.

3. On the chosen adjustment side (which is the front in this example), loosen the
front hex set screws using a 5/16" hex wrench. Note: When adjusting always
loosen at least 2 hex screws adjacent to each other.
4. Adjust the front height of the upper platen up by turning the adjustment nut counter
clockwise. Turning the adjustment nut clockwise will lower the front of the platen. Adjust in
180 degree increments, alternating between the two nuts being adjusted.
5. After each adjustment, tighten the hex set screws and then lower the top platen and
recheck to see if both are level. In the picture below, the platens are level. Tighten all set
screws and test with dough to insure platens are level.
13

TIMER WON'T COUNT DOWN
YES i---------1
Remove the rear cover.
Does the lower micro switch
"click" when the machine
handle is closed?
i------ ■ 1 NO
Take an Ohm meter and
verify that the switch
contacts are opening and
closing when the switch
lever is depressed. Are
they opening/closing?
Check the adjustment
of the switch so you can
hear the switch "click"
when the machine is
closed.
Replace the
Temp/Time
Controller
Replace the
Micro switch
PRESS IS NOT PRESSING DOUGH ENOUGH
Are you pressing the dough
YES t ■ -------i into the area(s) as outlined i------- ■ 1 NO
in the owner's manual?
With no dough in the machine, adjust the
thickness adjustment so that with the
handle closed the platens are just touching
each other. Does the alignment between
the u er and lower latens look even?
Review the
instructions on how to
properly press dough
in the owner's manual
for your machine.
NO
14
Take a folded rag or towel and place between
the upper and lower platens where they are
touching each other first. Lower the upper
platen and apply some handle pressure
to attempt to bend the platens back into
alignment. Remove the towel, close the handle 1 ■ ---""'1
and see if the alignment has improved. Repeat
as necessary until proper alignment is restored.

WARNING: Before cleaning, performing maintenance or repairs make sure the machine is turned off
and the machine is unplugged.
***This appliance is not waterproof. Never spray or pour water or any other
cleaning solution onto this appliance.***
CLEANING ALUMINUM UNCOATED HEAT PLATEN(S)
1. Unplug the machine and allow it to cool.
2. Open the heat platen for easier access.
3. Dampen a nonmetallic scrubbing sponge with a mild soap or detergent to remove any
excess material from the heat platen(s ).
4. Wipe clean with a dry cloth.
CLEANING PTFE (XYLON) COATED PLATEN(S) (OPTIONAL FEATURE)
1. Unplug the machine and allow it to cool.
2. Open the heat platen for easier access.
3. Clean the PTFE coated platen with a mild soap and warm water applied with a soft cloth or
sponge. Do not use steel wool, scrub sponges, kitchen or oven cleaners or any other kind of
abrasive material. This will damage the coating.
4. Wipe clean and dry with a cloth.
CLEANING OUTSIDE SURFACES OF THE MACHINE
Use a mild soap and warm water applied with a soft cloth or sponge. Do not use steel wool, scrub
sponges, kitchen or oven cleaners or other abrasives that will damage the painted surface.
*DX Series dough presses are available in White or Stainless Steel housings.*
LUBRICATION
Your press requires lubrication every 15,000 cycles or every 6 months. Use NSF/NLGl2 rated food
grade grease (such as Bel-Rey No-Tax #2 or equivalent). Lubrigate all moving or hinged points.
CIRCUIT BREAKER RESETTING
Should the circuit breaker trip, simply allow the machine to cool for 2 minutes and
then reset the circuit breaker by pressing the button back in to allow the machine to
come back on. If the circuit breaker continues to trip, have an electrician diagnose
the cause of the fault.
15

16

ITEM#I
PART# TITLE
ITEM#I
PART# TITLE
1 10021 WASHER LOCK HEL SPR #8 ZP 55 67768 VALVE SOLENOID 5/2 120V 1/4NPT
2 10027 SCREW FHSKT 3/8-16X1 .000 SS 56 67776 FTG MUFFLER 1/4NPT SINT BRZ
3 10341 SCREW CPSKT 3/8-16X1 .500 GD 8 57 70268 DECAL HIX
1.0. 3" X 3" SILVER
4 10454 DECAL CLEAN AIR 58 70899 SCREW MCH 6-32X0.750 FHPH
5 10664 DECAL MADE
IN USA 59 71041 SEAL SHAFT 2.500
6 10777 BOLT 5/16-18x1-1/4 60
71161 FTG BULKHD 1/4NPT BRS
7 10843 BOLT 3/8-16X0.750
61 72223 TERM BO 601-2-KT37, 38,39
8 10850 BOLT 3/8-16 X 1.000 62 73247 NUT 3/8-16 JAM NYLON INSERT ZPS
9 10963 DECAL, QR CODE DXP 63 74609 CORDSET 120v 16/3
SJOW5-15P
10 11072 BOLT 3/8-24x1 .000 64 76141 BEARING
1" 2 BOLT FLANGE
11 11327 DECAL, DOUGHXPRESS DOMED 6.75 X 1.5 65 76752 FUSE MDA-10/TCA 10A
12* 11345 WIRE CUT LIST DXA
RP 120V 4.3" 66 79418 WASHER LOCK HEL SPR 3/8 ZP
13 11404 SCREW MCH 10-32X0.375 SS 67 8600221 ASSEMBLY FRAME WITH SUPPORTS
LV
14 11430 DECAL, THICK THIN DXA4.3" 68 8601034 DP JACK HOUSING
15* 11544 CABLE TIE CT4S-M 3-3/4 69 8601036
DP STOP JACKADJUSTABLE
16 13250 CORD GRIP HEYCO 1557 RDD201 70 8601037
DP JACK RACK
17 13919 WASHER LOCK HEL SPR #4 ZP
71 8601039 DP CAM ROLLER MOUNT BLOCK
18 14524 SCREW MCH 4-40X0.250 PHPH 72 8601042
DP MOUNT CYLINDER/ SET SCREW
19 14571 NUT 3/8-16 ZPS 73 8601043
DP PINION SHAFT
20 14605 NUT 5/16-18 ZPS 74 8601067
DP SPACER FRAME PINION
21 15321 SCREW MCH 10-32x0.375 PHPH 75 8601083 M-DP LEG
3"
22 25720 WASHER FLT .406X1 .500X.120 ZPS 76 8601085 SPACER HOUSING FRAME COVER DXA
23 28142 SCREW FHSKT 5/16-18x1 .000 77 8601409 JACK SHAFT DXA
LV
24 28630 FTG 1T EL MALE 1/4Tx3/8NPT 78 8601952 TUBE 0.250ODx0.167ID 9.75
25 30910 WASHER LOCK HEL SPR 5/16 ZP 79 8607051 ASSY., LOWER PLATEN REMOVEABLE 18 INCH
26 32228 WASHER LOCK HEL SPR #10 ZP 80 8620129 ASSY. UPPER PLATEN 120V
LV 4.3" CLCD
27 32680 BOLT CAR 5/16-18x1 .250 81 8620323 ASSY. DP LOWER PLATEN RECEIVER NO HEAT
28* 33022 MANUAL OWNERS
TX/ 0-TX
82 8620332 ASSEMBLY, 1/0 / PWR SUPPLY DX 4.3"
29 33605 DECAL, UNPLUG MACHINE 83 8621047 M-LIMIT SWITCH MOUNT
30 34066 DECAL FUSE MDA-10 84 8621100 P-ASSY UPPER PLATEN MOUNT PLATE
31 34592 SCREW MCH 8-32x0.625 PHPH 85 8621111
M-HANDLE LC
32 37060 SWITCH ROLLER V7-1C1308-201 86 8621153 M-DX JACK
.5 HEX SHAFT
33 37125 SCREW MCH 4-40X0.625 RHPH 87* 8621174 DX SERIES PACKAGING
34 50083 SCREW MCH 10-32X0.375 THPH SS 88 8621212 ASSY, UPPER HOUSING DXE 4.3" CLCD
SS
35 50682 FTG 1T EL MALE 1/4Tx1/4NPT 89 8621216 HOUSING, BOTTOM DXA 4.3" CLCD STAINLESS
36 61220 ROD END 3/8-24
RH FEM 90 8621221 BOTTOM COVER 4.3" CLCD
37 61247 BEARING CAM FLWR .75x.5x3/8-24
91 8621226 COVER, FRAME ARCH STAINLESS STEEL
38 61255 GEAR SPUR 10P-14.5A-25T 92 8621242 ASSEMBLY, DISPLAY THREE SWITCH SS
39 61263 BUSHING TAPERED
1" ID
93 8621261 DXA HOUSING FRAME COVER 4.3" CLCD
SS
40 61417 DP CYLINDER RACK 94 89276 BOLT 3/8-16x5.000
41 61638 FUSE HOLDER S8301-1 BUSSMANN 95 90134 SCREW CPSKT 1/4-20x0.750
42 61646 CYLINDER DOUBLE ACTING 3x3
43 62251 SCREW SET 3/8-16x0.625
DP
44 62278 SCREW SET 5/16-18x0.500 NT
45 62448 WIRE CABLE CLIP ADHESIVE BACK
46 62537 NUTALLEN 3/8-24
47 62553 FTG 1T FLOW CTRL 1/4Tx1/8MPT
48 62561 KNOB PHENOLIC CL 852-PB
49 62693 FTG BUSHING 1/8x3/8NPT BRS
50 62731 RELAY SS 25A 3-32VDC INPUT
51 63711 FOOT RUBBER 1-1/2"ODx1/4"
52 63746 SCREW SET 3/8-16x1 .750
53 63932 FTG 1T EL MALE 3/8Tx1/4NPT STL
54 66729 SCREW MCH 10-32x0.375 GRND
17

(S) •
i-
" I 0 /4
~
ITEM#!
PART# TITLE
109 8621153 M-DX JACK
.5 HEX SHAFT
110 8621174 DX SERIES PACKAGING
111 8621212 ASSY, UPPER HOUSING DXE 4.3" CLCD
SS
112 8621217 HOUSING, BOTTOM 4.3" CLCD STAINLESS
113 8621221 BOTTOM COVER 4.3" CLCD
114 8621226 COVER, FRAME ARCH STAINLESS STEEL
115 8621230
DX HOUSING FRAME COVER 4.3" CLCD SS
116 8621242 ASSEMBLY, DISPLAY THREE SWITCH SS
117 89540 SCREW MCH 8-32x0.375 PHPH
18

ITEM#I
PART# TITLE
ITEM#I
PART# TITLE
1 10021 WASHER LOCK HEL SPR #8 ZP 55 70597 SCREW SET 5/16-24x0.625 CP
2 10024 SCREW SET 3/8-24 X 2.000 56 70899 SCREW MCH 6-32X0.750 FHPH
3 10027 SCREW FHSKT 3/8-16X1 .000 SS 57 71001 CONTROL STEPPER STAC5-Q-N220
4 10341 SCREW CPSKT 3/8-16X1 .500 GD 8 58 71019
FUSEABC-3
5 10660 BOLT 1/4-20X0.500 59 71025 HARNESS DB25 DXE
6 10664 DECAL MADE
IN USA 60 71041 SEAL SHAFT 2.500
7 10678 BOLT 1/4-20x0.750
61 72223 TERM BO 601-2-KT37, 38,39
8 10850 BOLT 3/8-16 X 1.000 62 73247 NUT 3/8-16 JAM NYLON INSERT ZPS
9 10963 DECAL, QR CODE DXP 63 74609 CORDSET 120v 16/3
SJOW5-15P
10 11300 DECAL, THICK THIN 64 76752 FUSE MDA-10/TCA 10A
11 11327 DECAL,
DOUGHXPRESS DOMED 6.75 X 1.5 65 77230 NUT 8-32 ZPS
12 11340 WIRE
KIT, DXE 4.3" RP 120V 66 79418 WASHER LOCK HEL SPR 3/8 ZP
13 11404 SCREW MCH 10-32X0.375 SS 67 79426 WASHER LOCK HEL SPR 1/4 ZP
14 13103 SCREW MCH 4-40x0.750 RHSL 68 8600202 ASSEMBLY, DXE GEARBOX 3
15 13250 CORD GRIP HEYCO 1557 RDD201 69 8600920
DP JACK SHAFT HOUSINGASSY.
16 13919 WASHER LOCK HEL SPR #4 ZP 70 8601083 M-DP LEG
3"
17 14524 SCREW MCH 4-40X0.250 PHPH 71 8601217 M-DXE ADJSMNT SCREW RETAINER
18 14571 NUT 3/8-16 ZPS 72 8601219 M-DXE JACKADJ STOP
19 14647 NUT HEX JAM 3/8-16 NC ZP 73 8601220 M-DXE DRIVE PIN
20 15131 SCREW SET 1/4-20x0.250 74 8601286 BRACKET, TRANSFORMER 70346 DXE
21 15321 SCREW MCH 10-32x0.375 PHPH 75 8603018 DXE MAIN SHAFT
22 15347 SCREW MCH 10-24x0.750 RHPH 76 8603101 DXE LINK STABILIZER
23 16683 WASHER FLT .375x0.875x.078 ZPS 77 8603103 M- LINK CRANK LARGE
24 24074 WASHER FLT .219x0.500x.047 ZPS 78 8603105 DXE LINK FOLLOWER
25 25720 WASHER FLT .406X1 .500X.120 ZPS 79 8603110 DXE ADJUSTMENT SCREW CAP
26 28142 SCREW FHSKT 5/16-18x1 .000 80 8603115 PIN CRANK LARGE
27 31823 SWITCH MICRO SMALL SEMI-HOOK
81 8603116 M- PIN ROD LARGE
28 32224 SCREW SET 3/8-16x0.375
DP
82 8603117 DXE PIN STABILIZER
29 32228 WASHER LOCK HEL SPR #10 ZP 83 8603118 DXE PIN FOLLOWER
30 33019 MANUAL OWNERS DXE 84 8603124 LINK MAIN LARGE 1/32 CHAMFER LEFT
31 33071 DETENT 3/8-16X0.188 BALL 85 8603128 LINK MAIN LARGE 1/32 CHAMFER RIGHT
32 33605 DECAL, UNPLUG MACHINE 86 8603129 O-DXE SWITCH ARM
33 34066 DECAL FUSE MDA-10 87 8603502 DXE MAIN SHAFT BUSHING
34 34592 SCREW MCH 8-32x0.625 PHPH 88 8603503 M-DXE PIN RETAINER
35 37060 SWITCH ROLLER V7-1C1308-201 89 8605007
DP DXE FAN ASSY 120V
36 37125 SCREW MCH 4-40X0.625 RHPH 90 8607051 ASSY., LOWER PLATEN REMOVEABLE 18 INCH
37 39446 GROMMET .313IDx.563 GRV 91 8607052 ASSY., LOWER PLATEN REMOVEABLE 17 INCH
38 39586 BEARING 1-1/4" 2 BOLT FLANGE 92 8607053 ASSY., LOWER PLATEN REMOVEABLE 16 INCH
39 39748 KEY STL .250x.250x1. 75 UNDSZ 93 8607054 ASSY., LOWER PLATEN REMOVEABLE 14 INCH
40 50083 SCREW MCH 10-32X0.375 THPH SS 94 8607055 ASSY., LOWER PLATEN REMOVEABLE 12 INCH
41 50628 SCREW MCH 6-32x2.000 RHPH 95 8607056 ASSY., LOWER PLATEN REMOVEABLE 10 INCH
42 61220 ROD END 3/8-24
RH FEM 96 8607057 ASSY., LOWER PLATEN REMOVEABLE 8 INCH
43 61638 FUSE HOLDER S8301-1 BUSSMANN 97 8607058 ASSY., LOWER PLATEN REMOVEABLE 18"
44 62448 WIRE CABLE CLIP ADHESIVE BACK 98 8609217 BRACKET, STAC5 MOUNTING
45 62561 KNOB PHENOLIC CL 852-PB 99 8620129
ASSY. UPPER PLATEN 120V LV 4.3" CLCD
46 62731 RELAY SS 25A 3-32VDC INPUT 100 8620171 ASSY FRAME WITH SUPPORTS
47 63711 FOOT RUBBER 1-1/2"ODx1/4"
101 8620323 ASSY. DP LOWER PLATEN RECEIVER NO HEAT
48 63746 SCREW SET 3/8-16x1 .750 102 8620332 ASSEMBLY, 1/0 / PWR SUPPLY DX 4.3"
49 66729 SCREW MCH 10-32x0.375 GRND 103 8621026 JACK SHAFT D-TXM-2-18
50 68330 WASHER LOCK #6 SPLIT ZPS 104 8621047 M-LIMIT SWITCH MOUNT
51 70045 BOLT 3/8-16 X 3.750 105 8621064 M-WIRE CLAMP BASE
52 70268 DECAL HIX I.D.
3" X 3" SILVER 106 8621065 M-WIRE CLAMP CAP
53 70346 TRANSFORMER PH150MQMJ 107 8621100 P-ASSY UPPER PLATEN MOUNT PLATE
54 70563 BOLT CAR 3/8-16x1 .250 108
8621111
M-HANDLE LC
19

20
~~~.
63 93
48
47
NOTES
I. F£FEREN CEWIRINGDL/,, GW.M 8621225
2.REFE F£N CEMOOEL#8620195
. Q---@
------------~o
- 3
17
/ .... /ct:>----@
,,/--/
CS>
(S) •
ITEM# I PART# TITLE
109 8621237 HANDLE STOP, DX SHEETMETAL
110 8621240 ASSEMBLY, DISPLAY NO SWITCHES SS
111 90134 SCREW CPSKT 1/4-20x0.750