DOUXE DXM4 User manual

English
Instruction Manual
DXM4- Monitor stand

UNPACKING INFORMATION
1. Carefully open the carton packaging to avoid potential paper cuts.
2. Remove the contents and lay them out for easy identification during installation.
3. Verify that all components are present and undamaged by cross-referencing with
the parts list on page 2.
4. Do not use damaged or defective parts.
5. Before attempting installation, thoroughly read all provided instructions.
SAFETY INFORMATION
1. Please do not begin installation until you have thoroughly read and understood
these instructions.
2. Do not exceed the maximum load capacity specified for this product.
3. Improper installation may result in property damage or personal injury.
4. This product contains small parts that could pose a choking hazard. Keep these
items and the product packaging out of reach of children.
5. Use appropriate safety equipment during installation.
6. It is recommended that two individuals perform this installation for proper support
and handling.
7. In case of uncertainty or ambiguity, consult a qualified contractor or installation
specialist.
1

Supplied Parts List
①Pole X1 ②Swivel Arm X1 ③VESA Plate X4 ④“C” Clamp X1
⑤“C” Clamp Brace X1 ⑥Extended pole X1 AM6 Nut X4 BM8x12 Bolt X2
CM5x16 Bolt X3 DM4x30 Bolt X16 EM4x12 Bolt X16 FM4 Spacer x16
GWire Clip X2
KAllen Key
HWire Clip X2 IAllen Key JAllen Key
2

⑤
①
C
K
⑤
④
⑥
①
Step 1 Install the Pole to the Desktop
1. Secure "C" Clamp Brace (5) to Pole (1) with M5x16 (C) and secure tightly using
Allen Key (K).
2. Screw Extended Pole (6) onto Pole (1) securely, ensuring a tight fit.
3

J
B
B
Step 2 Mount Swivel Arms to Poles
2. Align "C" Clamp (4) and "C" Clamp Brace
(5) on top of each other, adjusting it to
match the thickness of your desktop. There
are three available positions for thickness
adjustment. Secure it using two M8x12
Bolts (B) and secure them with the Allen
Key (J).
1. Straighten the two Swivel Arms (2)
and attach them to Poles (1,6).
2. Use Allen key (I) to secure the
Swivel Arms (2) to Poles (1,6).
I
②
⑥
⑥
①
①
4

H
H
G
H
H
G
HHHH
③
E
E
E
E
D
H
H
H③
D
D
D
H
Step 3 Install Wire Clips
Step 4 Attach VESA Plate to Monitors
Evenly attach Wire Clip (H) to Swivel Arms (2). Also, attach Wire Clip (G) to Poles (1,6).
1. For flat-back monitors, directly
attach VESA Plate (3) to the
monitor and secure firmly using
M4x12 Bolts (E).
2. For curved-back monitors, add
M4 Spacer (F) and then VESA
Plate (3). Secure firmly using
M4x30 Bolts (D).
⑥
①
5

②
A
H
HH
J
J
Step 5 Align Swivel Arm with VESA Plate
Step 6 Organize Wires and Store Allen Keys
1. Slide the monitor onto Swivel
Arm (2), make sure Swivel Arm
(2) aligns with VESA Plate (3)
2. Organize wires and store Allen
Keys (I, J, K) in Wire Clip (G) for
future use.
1. Make necessary adjustments
using Allen Key (J), ensuring all
bolts are tightened.
2. Secure Swivel Arm (2) to VESA
Plate (3) with M6 Nut (A). Make
sure to Install M6 Nut (A) before
rotating the monitor.
6

SERVICE AND WARANTY
Douxe provides a 2-year warranty on its products. To get service during the warranty
period, the product needs to be returned with a proof of purchase. Product defects must
be reported within 2 years from the date of purchase. This warranty does not cover
damages caused by misuse or incorrect repair, parts subject to wear, defects that the
customer was aware of at the time of purchase; damages or defects caused by
customer neglect; damages or defects caused by third parties.
DISPOSAL - RECYCLE
Contribute to a cleaner living environment! Do not dispose of the Monitor stand with the
household waste. For proper recycling, please contact your local authority or your
household waste disposal service for further details on your nearest designated
collection point.
DISCLAIMER
Changes reserved; specifications are subject to change without stating grounds for
doing so.
Douxe II
Koperstraat 26 3067GL Rotterdam
The Netherlands KVK: 80934382
Contact: [email protected]
Website: www.douxe.net