Dranetz PR150/SP1B User manual

PR150/SP1B
PR150/SP2B
PR1500/SP7B
PR1500/SP8B
AC/DC CURRENT PROBES
User Instructions
5 Commonwealth Ave5 Commonwealth Ave5 Commonwealth Ave5 Commonwealth Ave
Woburn, MA 01801Woburn, MA 01801Woburn, MA 01801Woburn, MA 01801
Phone [phone]Phone [phone]Phone [phone]Phone [phone]
TollTollTollToll Free 1-800-517-8431Free 1-800-517-8431Free 1-800-517-8431Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com

1
WARNING
Death, serious injury, or fire hazard could result from improper
connection of this instrument. Read and understand this manual before
connecting this instrument. Follow all installation and operating
instructions while using this instrument.
Connection of this instrument must be performed in compliance with the
National Electrical Code (ANSI/NFPA 70-2011) of USA and any
additional safety requirements applicable to your installation.
Installation, operation, and maintenance of this instrument must be
performed by qualified personnel only. The National Electrical Code
defines a qualified person as “one who has the skills and knowledge
related to the construction and operation of the electrical equipment and
installations, and who has received safety training on the hazards
involved.”
Qualified personnel who work on or near exposed energized electrical
conductors must follow applicable safety related work practices and
procedures including appropriate personal protective equipment in
compliance with the Standard for Electrical Safety Requirements for
Employee Workplaces (ANSI/NFPA 70E-2012) of USA and any
additional workplace safety requirements applicable to your installation.
No part of this book may be reproduced, stored in a
retrieval system, or transcribed in any form or by any
means—electronic, mechanical, photocopying, recording,
or otherwise—without prior written permission from the
publisher, Dranetz, Edison, NJ 08818-4019.
Printed in the United States of America.
P/N 899216 Rev C 08.20.12

2
ADVERTENCIA
Una conexión incorrecta de este instrumento puede producir la muerte,
lesiones graves y riesgo de incendio. Lea y entienda este manual antes
de conectar. Observe todas las instrucciones de instalación y operación
durante el uso de este instrumento.
La conexión de este instrumento a un sistema eléctrico se debe realizar
en conformidad con el Código Eléctrico Nacional (ANSI/NFPA 70-2011)
de los E.E.U.U., además de cualquier otra norma de seguridad
correspondiente a su establecimiento.
La instalación, operación y mantenimiento de este instrumento debe ser
realizada por personal calificado solamente. El Código Eléctrico
Nacional define a una persona calificada como "una que esté
familiarizada con la construcción y operación del equipo y con los
riesgos involucrados."
El personal cualificado que trabaja encendido o acerca a los
conductores eléctricos energizados expuestos debe seguir
prácticas y procedimientos relacionados seguridad aplicable del trabajo
incluyendo el equipo protector personal apropiado en conformidad con el
estándar para los requisitos de seguridad eléctricos para los lugares de
trabajo del empleado (ANSI/NFPA 70E-2012) de los E.E.U.U. y
cualquier requisito de seguridad adicional del lugar de trabajo
aplicable a su instalación.
Test Equipment Depot - 800.517.8431 - 5 Commonwealth Ave, Woburn, MA 01801
TestEquipmentDepot.com

3
AVERTISSEMENT
Si l'instrument est mal connecté, la mort, des blessures graves, ou un
danger d'incendie peuvent s'en suivre. Lisez attentivement ce manuel
avant de connecter l'instrument. Lorsque vous utilisez l'instrument,
suivez toutes les instructions d'installation et de service.
Cet instrument doit être connecté conformément au National Electrical
Code (ANSI/NFPA 70-2011) des Etats-Unis et à toutes les exigences de
sécurité applicables à votre installation.
Cet instrument doit être installé, utilisé et entretenu uniquement par un
personnel qualifié. Selon le National Electrical Code, une personne est
qualifiée si "elle connaît bien la construction et l'utilisation de
l'équipement, ainsi que les dangers que cela implique".
Le personnel qualifié qui travaillent dessus ou s'approchent des
conducteurs électriques activés exposés doit suivre des pratiques en
matière et des procédures reliées par sûreté applicable de travail
comprenant le matériel de protection personnel approprié conformément
à la norme pour des conditions de sûreté électriques pour les lieux de
travail des employés (ANSI/NFPA 70E-2012) des Etats-Unis et toutes
les conditions de sûreté additionnelles de lieu de travail applicables à
votre installation.

4
WARNUNG
Der falsche Anschluß dieses Gerätes kann Tod, schwere Verletzungen
oder Feuer verursachen. Bevor Sie dieses Instrument anschließen,
müssen Sie die Anleitung lesen und verstanden haben. Bei der
Verwendung dieses Instruments müssen alle Installation- und
Betriebsanweisungen beachtet werden.
Der Anschluß dieses Instruments muß in Übereinstimmung mit den
nationalen Bestimmungen für Elektrizität (ANSI/NFPA 70-2011) der
Vereinigten Staaten, sowie allen weiteren, in Ihrem Fall anwendbaren
Sicherheitsbestimmungen, vorgenommen werden.
Installation, Betrieb und Wartung dieses Instruments dürfen nur von
Fachpersonal durchgeführt werden. In dem nationalen Bestimmungen
für Elektrizität wird ein Fachmann als eine Person bezeichnet, welche
"mit der Bauweise und dem Betrieb des Gerätes sowie den
dazugehörigen Gefahren vertraut ist."
Qualifiziertes Personal, das an bearbeiten oder herausgestellte
angezogene elektrische Leiter sich nähern, muß anwendbare Sicherheit
bezogener Arbeit Praxis und Verfahren einschließlich passende
persönliche schützende Ausrüstung gemäß dem Standard für elektrische
Sicherheitsauflagen für Angestellt-Arbeitsplätze (ANSI/NFPA 70E-2012)
der Vereinigten Staaten und alle zusätzlichen
Arbeitsplatzsicherheitsauflagen folgen, die auf Ihre Installation
anwendbar sind.

5
SAFETY PRECAUTIONS
The following safety precautions must be followed whenever any type of
voltage or current connection is being made to the instrument.
When connecting to electric circuits or pulse initiating equipment,
open their related breakers. DO NOT install any connection of the
instrument on live power lines.
Connections must be made to the instrument first, then connect to
the circuit to be monitored.
Wear proper personal protective equipment, including safety glasses
and insulated gloves when making connections to power circuits.
Hands, shoes and floor must be dry when making any connection to
a power line.
Make sure the unit is turned OFF before connecting probes to the
rear panel.
Before
each use, inspect all cables for breaks or cracks in the
insulation. Replace immediately if defective.
If the equipment is used in a manner not specified in this user’s
guide, the protection provided by the equipment may be impaired.
These safety precautions are repeated where appropriate throughout
this manual.

6
INTRODUCTION
These user instructions provide descriptive and operational information
about the optional PR150/SP1B, PR150/SP2B, PR1500/SP7B and
PR1500/SP8B current probes.
The PR150/SP1B, PR150/SP2B, PR1500/SP7B and PR1500/SP8B
current probes have been designed for accurate non-intrusive
measurement of AC and DC current.
The PR150/SP1B, PR150/SP2B, PR1500/SP7B and PR1500/SP8B
conform to the latest directives concerning safety and electromagnetic
compatibility.
• European Low Voltage Directives 73/23/EEC and 93/68/EEC
• European EMC Directive 89/336/EEC
Safety Standards
EN61 01 0-1: 1993, General Requirements
Safety requirements for electrical equipment for measurement, control
and laboratory use
EN61010-2-032: 1995, IEC1010-2-032: 1994-12.
Particular requirements for hand held current clamps for electrical
measurement and test
EN61010-2-031: 1995, IEC1010-2-031: 1993-12.
Particular requirements for hand held current clamps for electrical
measurement and test
600V Cat III Pollution degree 2
EMC Standards
EN50082-1: 1992 Generic Immunity Standard
Part 1. Residential, commercial & light industry
EN50081-1: 1992 Generic Emission Standard
Part 1. Residential, commercial & light industry

7
CONNECTION PROCEDURE
The PR150/SP1B, PR150/SP2B, PR1500/SP7B and PR1500/SP8B are
designed to be safe under the following conditions:
indoor use
altitude up to 2000 m
temperature 0°C to + 50°C
maximum relative humidity 80% for temperatures up to 31°C
decreasing linearly to 40% relative humidity at 50°C
Use of the probe on uninsulated conductors is limited to 600V RMS or
DC and frequencies below 1 kHz. Safety in its use is the responsibility of
the operator who must be a suitably qualified or authorized person.
When using the probe ensure that your fingers are behind the protective
barrier (see Figure 1).
Do not use the probe if any part of the probe including the lead and
connector(s) appear to be damaged or if a malfunction of the instrument
is suspected. Clean the case periodically by wiping it with a damp cloth
and detergent. Do not use abrasive cleaners or solvents. Do not
immerse the probe in liquids.
WARNING
To reduce the risk of fire, electrical shock, or physical injury it is
strongly recommended to make connections to the instrument with
all circuits de-energized. If it is necessary to make connections on
energized circuits they must be made by Qualified personnel ONLY.
The National Electrical Code defines a qualified person as “one who has
the skills and knowledge related to the construction and operation of the
electrical equipment and installations, and who has received safety
training on the hazards involved.”
Qualified personnel that work on or near exposed energized electrical
conductors must follow applicable safety related work practices and
procedures including appropriate personal protective equipment in
compliance with the Standard for Electrical Safety Requirements for
Employee Workplaces (ANSI/NFPA 70E-2012) of USA and any
additional workplace safety requirements applicable to your installation.
Always refer to the applicable User’s Guide for additional information
concerning installation, operation, and connections of Dranetz or Original
Equipment Manufacturer’s instructions applicable to your installation.

8
OPERATING INSTRUCTIONS
Refer to Figure 1 and Figure 2.
1. Switch On (PR150/SP1B and PR1500/SP7B)
Connect the external power supply to the probe via the 2.1 mm jack
socket, switch on the power source and check that the LED on the
handle of the probe is lit.
2. Switch On (PR150/SP2B and PR1500/SP8B)
Switch on the probe using the On - Off switch and check that the
LED is lit.
3. Battery Replacement (PR150/SP2B and PR1500/SP8B)
When the red LED fails to light with the switch in the On position, the
battery must be replaced. Refer to Figure 2 and use the following
procedure to replace the battery.
Unclamp the probe from the conductor, turn it off by using the On -
Off switch and disconnect the output leads, from external equipment.
With a small tool remove the cover of the battery compartment and
incline the probe such that the battery can be removed from the
compartment. Replace the battery and re-fit the battery cover.
Replacement with other than the specified type of battery will
invalidate the warranty. Only fit battery type 9 V PP3, Alkaline 6 LR
61.
4. Zero adjustment
The output zero offset voltage of the probe may change due to
thermal shifts and other environmental conditions. To adjust the
output voltage to zero, rotate the thumbwheel located on the probe
handle. Ensure that the probe is away from the current carrying
conductor while the adjustment is made.
SAFETY WARNING
Before removing the battery cover, make sure that
the
p
robe is remote from an
y
live electrical circuit.

9
5. Current measurement
Connect the output lead to a multimeter. Select the AC or DC mV
range on the multimeter as appropriate to the current measurement.
If necessary adjust the probe output voltage to zero as described in
Step 4. Clamp the jaws of the probe round the conductor ensuring a
good contact between the closing faces of the jaws.
Observe and take measurement as required. Positive output
indicates that the current flow is in the direction shown by the arrow
on the probe.
True RMS readings can be obtained by using an appropriate true
RMS reading multimeter. Core eddy current heating is produced
when I RMS x f > 400.000. This will limit the maximum measurable
current at high frequencies.
Test Equipment Depot - 800.517.8431 - 5 Commonwealth Ave, Woburn, MA 01801
TestEquipmentDepot.com

10
BATTERY SUPPLY
The PR150/SP2B, and PR1500/SP8B current probes are supplied with a
9V battery and will operate on battery power typically for approximately
75 hours of continuous operation.
EXTERNAL SUPPLY
The PR 150/SP1B and PR 1500/SP7B current probes require an
external 9V power supply and each probe can be powered by a separate
adapter or by one adapter and an optional RR/PS/4A adapter cable
which allows the connection of 4 PR series probes to a single 9VDC
source . Recommended AC adapter details are as follows.
Product Number
Input
Voltage
Input
Plug Type Output
PR9VUA 100-240 VAC,
50/60 Hz
US, Euro,
UK,
Australia
+9VDC, 1.11 A
If using other AC adapters not listed above, the probe is to be externally
powered by an applicable agency Listed Limited Power supply only.
The DC input jack on the side of the probe enclosure accommodates a
2.1 x 5.5 mm barrel connector using the center pin as the positive
terminal and the outside barrel connection as the negative terminal.
It is recommended that each probe to be powered by one adapter to
power each probe if using non-Dranetz accessories.
Note: Use of non-Dranetz accessories may be susceptible to
noise influencing current measurements and use of one adapter
to power 4 probes is not recommended. Each probe should be
powered by a separate adapter.
( - terminal)
( + terminal)

11
FIGURE 1

12
FIGURE 2

13
SPECIFICATIONS
Electrical Data – PR150/SP1B and PR150/SP2B
(All accuracies stated at 23°C ± 1°C)
Nominal Current In 150 A DC and ACRMS
Measuring Range ± 200 A
Overall accuracy (at 23°C) ± 1% of rdg
(10% to 120%)
± 2% max.
Resolution ± 100 mA
Output sensitivity 10m V I A
Frequency range DC to 5 kHz (-3dB)
Dielectric strength 5.5 kV / 50Hz I 1 min
General Data - PR150/SP1B and PR150/SP2B
Operating temperature -10°C to +50°C
Storage temperature with Battery removed -20°C to +70°C
Load impedance (minimum) > 10 kΩand ≤100 pF
Conductor diameter 50 mm max.
Jaw opening 52 mm max.
Weight 600 g
Output cable 2m screened, PVC
Connector Type Hypertronics D01, 4 pin
PR150/SP1B
External Power Supply 9V DC (± 2 V)/20 mA
Via 2 .1 mm Jack Plug
PR150/SP2B
Power Supply 9V Alkaline, P3/6LR61
75Hrs, Low Battery
Indicator

14
Electrical Data – PR1500/SP7B and PR1500/SP8B
(All accuracies stated at 23°C ± 1°C)
Nominal Current In 1500 A DC and ACRMS
Measuring Range ± 1800 A
Overall accuracy (at 23°C) ± 1% of rdg
(10% to 120%)
± 2% max.
Resolution ± 100 mA
Output sensitivity 1 mV I A
Frequency range DC to 5 kHz (-3dB)
Dielectric strength 5.5 kV / 50Hz I 1 min
General Data - PR1500/SP7B and PR1500/SP8B
Operating temperature -10°C to +50°C
Storage temperature with Battery removed -20°C to +70°C
Load impedance (minimum) > 10 kΩand ≤100 pF
Conductor diameter 50 mm max.
Jaw opening 52 mm max.
Weight 600 g
Output cable 2m screened, PVC
Connector Type Hypertronics D01, 4 pin
PR1500/SP7B
External Power Supply 9V DC (± 2 V)/20 mA
Via 2 .1 mm Jack Plug
PR1500/SP8B
Power Supply 9V Alkaline, P3/6LR61
75Hrs, Low Battery
Indicator

15
SCALE FACTORS
Probe Model Number Range Scale Factor
PR 150 150A 100
PR 1500 1500A 1000

16
STATEMENTS AND NOTICES
Statement of warranty
All products of Dranetz are warranted to the original purchaser against
defective material and workmanship for a period of one year from the
date of delivery. Dranetz will repair or replace, at its option, all defective
equipment that is returned, freight prepaid, during the warranty period.
There will be no charge for repair provided there is no evidence that the
equipment has been mishandled or abused. This warranty shall not
apply to any defects resulting from improper or inadequate maintenance,
buyer-supplied hardware/software interfacing, unauthorized modification
or misuse of the equipment, operation outside of environmental
specifications, or improper site preparation or maintenance.
Statement of reliability
The information in this manual has been reviewed and is believed to be
entirely reliable, however, no responsibility is assumed for any
inaccuracies. All material is for informational purposes only and is
subject to change without prior notice.
Notice regarding proprietary rights
This publication contains information proprietary to Dranetz. By
accepting and using this manual, you agree that the information
contained herein will be used solely for the purpose of operating
equipment of Dranetz.
Copyright
This publication is protected under the Copyright laws of the United
States, Title 17 et seq. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into
any language or computer language, in any form, by any means,
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise, without the prior written consent of Dranetz, 1000 New
Durham Road, Edison, New Jersey 08818.
Copyright © 2012 Dranetz
All Rights Reserved. Printed in the United States of America.
Test Equipment Depot - 800.517.8431 - 5 Commonwealth Ave, Woburn, MA 01801
TestEquipmentDepot.com