Draytek Vigor2952 Series User manual

i

ii
Intellectual Property Rights (IPR) Information
Copyrights © All rights reserved. This publication contains information that is protected
by copyright. No part may be reproduced, transmitted, transcribed, stored in
a retrieval system, or translated into any language without written permission
from the copyright holders.
Trademarks
The following trademarks are used in this document:
 Microsoft is a registered trademark of Microsoft Corp.
 Windows, Windows 95, 98, Me, NT, 2000, XP, Vista, 7, 8 and
Explorer are trademarks of Microsoft Corp.
 Apple and Mac OS are registered trademarks of Apple Inc.
 Other products may be trademarks or registered trademarks of
their respective manufacturers.
Safety Instructions and Approval
Safety
Instructions
 Read the installation guide thoroughly before you set up the router.
 The router is a complicated electronic unit that may be repaired
only be authorized and qualified personnel. Do not try to open or
repair the router yourself.
 Do not place the router in a damp or humid place, e.g. a bathroom.
 Do not stack the routers.
 The router should be used in a sheltered area, within a
temperature range of 0 to +45 Celsius for Vigor2952 and 0 to +40
Celsius for Vigor2952P.
 Do not expose the router to direct sunlight or other heat sources.
The housing and electronic components may be damaged by direct
sunlight or heat sources.
 Do not deploy the cable for LAN connection outdoor to prevent
electronic shock hazards.
 Keep the package out of reach of children.
 When you want to dispose of the router, please follow local
regulations on
conservation of the environment.
Warranty
We warrant to the original end user (purchaser) that the router will be free
from any defects in workmanship or materials for a period of two (2) years
from the date of purchase from the dealer. Please keep your purchase receipt
in a safe place as it serves as proof of date of purchase. During the warranty
period, and upon proof of purchase, should the product have indications of
failure due to faulty workmanship and/or materials, we will, at our discretion,
repair or replace the defective products or components, without charge for
either parts or labor, to whatever extent we deem necessary tore-store the
product to proper operating condition. Any replacement will consist of a new
or re-manufactured functionally equivalent product of equal value, and will
be offered solely at our discretion. This warranty will not apply if the product
is modified, misused, tampered with, damaged by an act of God, or subjected
to abnormal working conditions. The warranty does not cover the bundled or
licensed software of other vendors. Defects which do not significantly affect
the usability of the product will not be covered by the warranty. We reserve
the right to revise the manual and online documentation and to make changes
from time to time in the contents hereof without obligation to notify any
person of such revision or changes.

iii
Vigor2952 Series
Dual-WAN Security Firewall
Quick Start Guide
T
Ta ab bl le e o of f C Co on nt te en nt ts s
1
1. . P Pa ac ck ka ag ge e C Co on nt te en nt t .................................................................................................. 1
2
2. . P Pa an ne el l E Ex xp pl la an na at ti io on n ................................................................................................. 2
3
3. . H Ha ar rd dw wa ar re e I In ns st ta al ll la at ti io on n ........................................................................................... 6
3
3. .1 1 N Ne et tw wo or rk k C Co on nn ne ec ct ti io on n ................................................................................................................... 6
3
3. .2 2 W Wa al ll l- -M Mo ou un nt te ed d I In ns st ta al ll la at ti io on n ........................................................................................................... 7
4
4. . S So of ft tw wa ar re e C Co on nf fi ig gu ur ra at ti io on n ........................................................................................ 7
5
5. . C Cu us st to om me er r S Se er rv vi ic ce e ............................................................................................... 12

1
1
1. . P Pa ac ck ka ag ge e C Co on nt te en nt t
Take a look at the package content. If there is anything missed or damaged, please contact
DrayTek or dealer immediately.
Vigor router Quick Start Guide
RJ-45 Ethernet Cable
Rack mount kit (brackets)
Power Cord

2
2
2. . P Pa an ne el l E Ex xp pl la an na at ti io on n
V
Vi ig go or r 2 29 95 52 2
LED
Stat
us
Explanation
ACT
(Activity)
B
linking
The router is powered on and running
normall
y.
Off
The router is powered off.
USB1~USB2
On
A USB device is connected
and
active.
B
linking
The data is transmitting.
SFP
On
No fiber line connected.
Off
File lin
e connected.
WAN1~WAN2
On
The WAN conn
ection is ready.
B
linking
It will blink while transmitting data.
QoS
On
The
QoS function is active.
CSM On The profile of CSM (Content Security Management) for
IM/P2P application is enabled from Firewall >> General
Setup
. (Such p
rofile is established u
nder
CSM
menu)
.
VPN
On
VPN tunnel is up and down.
Off
VPN servi
ces are disabled.
B
linking
Traffic is passing through VPN
tunnel.
LED on Connector
WAN1/SFP
WAN2
LAN1~LAN4
Left LED
(Green)
On
The port is connect
ed.
Off
The port is disconnected.
Blinking
The data is transmitting.
Right LED
(Green)
On
The port is connect
ed with 1000Mbps.
Off
The port is connected with 10/100Mb
ps.

3
Interfa
ce
Description
Factory Reset Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press the hole and
keep for more than 5 seconds. When you see the ACT LED begins to
blink rapidly than usual, release the button. Then the router will
restart with the factory default configuration.
WAN(SFP
)
Fiber c
onnector
for
accessing the Int
ernet
.
WAN1~WAN2
C
onnect
or for remote networked devices.
LAN1~LAN4
C
onne
ct
ors for
local networked devices.
USB1~USB2
C
onnect
or for a USB device (for 3G/4G USB Modem or printer).
PWR
Connector for a power
cord.
ON/OFF
Power Switch.
Note 1 Vigor router will use either Fiber WAN or WAN1 for Internet connection.
If both Fiber WAN and WAN1 are connected at the same time, Fiber WAN
will be the first choice.

4
V
Vi ig go or r 2 29 95 52 2P P
LED
Status
Explanation
ACT
(Activity)
B
linking
The router is powered on
and running
normall
y.
Off
The router is powered off.
USB1~USB2
On
A USB device is connect
ed
and
active.
B
linking
The data is transmitting.
SFP
On
No fiber line connected.
Off
File line connected.
WAN1~WAN2
On
The WAN conn
ection is ready.
B
linki
ng
It will blink while transmitting data.
QoS
On
The
QoS function is active.
PoE
On
Power
sourcing
equipment
for PoE is enabled.
Off
Power sourcing
equipment
for PoE is disabled.
VPN
On
VPN tunnel is up and down.
Off
VPN servi
ces are disabled.
B
linking
Traffic is passing through VPN
tunnel.
LED on Connector
WAN1/SFP
WAN2
LAN1~LAN4
Left LED
(Green)
On
The port is connected.
Off
The port is disconnected.
Blinking
The data is transmitting.
Right LED
(Green)
On
The port is connect
ed with 1
000Mbps.
Off
The port is connected with 10/100Mb
ps.

5
Interfa
ce
Description
Factory Reset Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press the hole and
keep for more than 5 seconds. When you see the ACT LED begins to
blink rapidly than usual, release the button. Then the router will
restart with the fa
ctory default configuration.
WAN(SFP)
Fiber c
onnector
for
accessing the Internet
.
WAN1~WAN2
C
onnect
or for remote networked devices.
LAN1~LAN4 Connectors for local networked devices.
Such connectors support PoE device with up to 30 watt power which
is
compliant with
IEEE
802.3at
standard
.
USB1~USB2
C
onnect
or for a USB device (for 3G/4G USB Modem or printer).
PWR
Connector for a power
cord.
ON/OFF
Power Switch.
Note 1 Vigor router will use either Fiber WAN or WAN1 for Internet connection.
If both Fiber WAN and WAN1 are connected at the same time, Fiber WAN
will be the first choice.
Note 2 The PoE Power budget is up to 60W.

6
3
3. . H Ha ar rd dw wa ar re e I In ns st ta al ll la at ti io on n
This section will guide you to install the router through hardware connection.
3
3. .1 1 N Ne et tw wo or rk k C Co on nn ne ec ct ti io on n
1. Connect a cable Modem/DSL Modem/Media Converter (depends on your requirement)
to any WAN port of router with Ethernet cable (RJ-45). Or, connect the fiber cable to
the WAN (SFP) port of router.
2. Connect one end of an Ethernet cable (RJ-45) to one of the LAN ports of the router and
the other end of the cable (RJ-45) into the Ethernet port on your computer (that device
also can connect to other computers to form a small area network).
3. Connect the power cord to the router’s power port on the rear panel, and the other
side into a wall outlet.
4. Power on the device by pressing down the power switch on the rear panel.
5. The system starts to initiate. After completing the system test, the ACT LED will light
up and start blinking.

7
3
3. .2 2 W Wa al ll l- -M Mo ou un nt te ed d I In ns st ta al ll la at ti io on n
Vigor can be mounted on the wall by using standard brackets shown below.
Choose a flat surface (on the wall) which is suitable for placing the router. Make the screw
holes on the short side of the bracket aim at the screw holes on the router. Next, fasten
both the bracket and the router with two screws; and fasten both the wall and the bracket
with another two screws. Refer to the following figure.
Then, continue to fasten the screws on the other side of the router and the wall with other
screws.
When you finished about procedure, the router has been mounted on the wall firmly.

8
4
4. . S So of ft tw wa ar re e C Co on nf fi ig gu ur ra at ti io on n
To access Internet, please finish basic configuration after completing the hardware
installation.
The Quick Start Wizard is designed for you to easily set up your router for Internet access.
You can directly access the Quick Start Wizard via Web Configurator.
1. Make sure your PC connects to the router correctly.
Note You may either simply set up your computer to get IP dynamically
from the router or set up the IP address of the computer to be the
same subnet as the default IP address of Vigor router
192.168.1.1.
2. Open a web browser on your PC and type http://192.168.1.1. A pop-up window will
open to ask for username and password. Please type “admin/admin” as the
Username/Password and click Login.

9
3. Now, the Main Screen will pop up.
4. Click Wizards>>Quick Start Wizard.
5. Enter the login password on the field of New Password and retype it on the field of
Confirm Password. Then click Next to continue.

10
6. On the next page as shown below, please select the WAN interface that you use. Then
click Next for next step.
7. On the next page as shown below, please select the appropriate protocol according to
the information from your ISP. For example, you should select PPPoE mode if the ISP
provides you PPPoE interface. Then click Next for next step.

11
PPPoE: If you click PPPoE as the protocol, after clicking Next, you will get the
following web page. Please manually enter the Username/Password provided by your
ISP. Then click Next.
Static IP: if you click Static IP, you will get the following page. Please type in the IP
address information originally provided by your ISP. Then click Next for next step.

12
DHCP: if you click DHCP, you will get the following page. Simply click Next to continue.
8. Now you can see the following screen. It indicates that the setup is complete. Different
types of connection modes will have different summary. Click Finish and then restart
the router. Afterward, you will enjoy surfing on the Internet.
5
5. . C Cu us st to om me er r S Se er rv vi ic ce e
If the router cannot work correctly after trying many efforts, please contact your
dealer/DrayTek for further help right away. For any questions, please feel free to send
e-mail to [email protected]m.