Drieaz Velo User manual

07-01844A F504/F505-230V 2013-10 Warranty 07-00427 1 Dri-Eaz Products, Ltd.
Owner’s Manual
Velo™& Velo™Pro Low Profile Airmover
Models F504-230V & F505-230V
DRI-EAZ PRODUCTS, LTD.
22 Plover Close, Interchange Park, Newport Pagnell, MK16 9PS
Tel: [phone] Fax: [phone] www.dri-eaz.co.uk
The Velo Airmover produces a high rate of airflow to accelerate the
evaporation of moisture from materials for restorative drying.
Patents: http://www.LBpatents.com
ORIGINAL INSTRUCTIONS
WARNING! To reduce the risk of fire or
electric shock, do not use this fan with any
solid-state speed control device.
WARNING! Unit must be grounded. Do not
use with an extension cord. Connect only to an outlet provided
with a ground fault interrupting device.
WARNING! Never operate a unit with a damaged power cord, as
this may lead to electrical or fire hazards. If the supply cord is
damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard. If
power cord is damaged, it must be replaced by a cord of the
same type and amperage rating.
WARNING! Do not touch grills when unit is operating.
NOTICE: Keep motor dry. For indoor use only.
NOTICE: Unplug when not in use or when moving unit.
NOTICE: Do not allow children to play with or around the unit.
Be sure the unit is inaccessible to children when not attended.
NOTICE: Always operate the unit on a stable, level surface so it
cannot fall and cause injury.
WARNING! Do not alter or modify your Velo in any way. Use
only replacement parts authorized by Dri-Eaz Products, Inc.
Modifications or use of unauthorised parts could create a hazard
and will void your warranty. Contact your authorised Dri-Eaz Ltd.
distributor for assistance.
This appliance can be used by children aged from 8 years and
above and persons with reduced physical sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazard involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
Fig. B: Operating Positions
Horizontal (for
horizontal surfaces)
Vertical (for walls
and ceilings)
Right edge (for
wall drying)
Left edge (for
wall drying)
Pro only:
Kickstand.
Rear cord wrap under
bottom edge. Wrap
cord clockwise.
Pro only: KWH
meter.
Inlet grill. Keep clear
of obstructions.
Outlet grill. Keep
clear of obstructions.
On/Off switch.
Carry strap
Fig. A: Parts Identification
Front Lift/Cord Wrap tab.
Wrap cord clockwise and
secure with hook-and-
loop tie.

07-01844A F504/F505-230V 2013-10 Warranty 07-00427 2 Dri-Eaz Products, Ltd.
OPERATING INSTRUCTIONS
Note that the Velo and Velo Pro can be placed in a variety of
positions for drying and air circulation. See Fig. B for details.
1. Unwrap the cord and plug the unit into a standard 230V
outlet. CAUTION: Be sure switch is in the off position before
connecting unit to power outlet.
2. Direct the Velo outlet toward the surface to be dried.
3. Press On switch
4. When surface is dry to the touch, switch the unit off and
reposition the unit in the next area to be dried.
5. When finished, unplug the unit and re-wrap the cord in a
clockwise direction around the front and rear cord wrap tabs
and secure with the hook-and-loop provided.
Note: The Velo Pro includes a kilowatt hour meter, useful for
tracking electrical consumption. See Fig. D.
For additional instructions about the use of airmovers for
restorative drying, visit www.DriEaz.co.uk and www.RSA-HQ-
UK.co.uk.
Transport and Storage
Always use the handle to load or carry the unit.
Wrap cord in a clockwise direction under front Cord Wrap tab
and rear bottom edge (Fig. A). Pull cord snug and secure with
hook-and-loop tie.
Units may be stacked for transport and storage.
When transporting in a vehicle, secure the unit(s) carefully to
prevent sliding and damage to the unit and/or injury to vehicle
occupants.
Keep unit dry. Do not expose the unit to rain or snow.
Maintenance
WARNING: Unplug unit before performing any maintenance.
Before each use
Inspect the power cord. If cord is damaged, do not use. Always
grasp the plug (not the cord) to unplug.
As needed
Clean housing and impeller. If dust accumulation is visible,
remove the four screws from the top, then turn the unit on its top
and remove the six fasteners from the bottom as shown (Fig. C).
Lift off the housing. Clean impeller assembly with a soft cloth. Do
not apply liquids to the impeller assembly. The housing may be
cleaned with a mild solution of detergent and warm water. Do not
use a hose to clean the unit. Ensure housing is completely dry
before reassembling.
FOR SERVICE CALL Dri-Eaz on [phone].
SPECIFICATIONS
Model Velo (F504-230V) Velo Pro (F505-230V)
Weight 9.52 kg 9.52 kg
Dimensions
(D × W × H)
61 × 45.7 × 22.9 cm 61 × 45.7 × 22.9 cm
Amp draw .53 amps (230V) .53 amps (230V)
Power 124W 124W
Max. Airflow 1190 m3/h 1190 m3/h
RPM 1280 1280
Rotation Clockwise Clockwise
Static pressure 28 mm (H2O) 28 mm (H2O)
Sound level (avg.) 65 dB 65 dB
Control On/Off switch On/Off switch
Cord length 4.6 m 4.6 m
Fan 6 blades 6 blades
Kickstand No Yes
Kilowatt Hour
Meter
No Yes
Construction
Rotomolded
polyethylene and
injection molded ABS
housing components;
steel wire inlet and
outlet grills.
Rotomolded
polyethylene and
injection molded ABS
housing components;
steel wire inlet and
outlet grills.
Safety CE CE
Specifications are subject to change without notice. Some values
may be approximate.
Fig. D: Pro model only: Kilowatt Hour
meter
To disassemble for
cleaning, first remove the
four screws from the
impeller assembly 1)
(below), then turn the unit
on its top and 2) remove
the six screws from the
base. Lift off the housing.
Retain screws and
washers for reassembly.
1. Remove impeller
assembly screws (×4).
2. Remove base
screws (×6) and
lift out housing.
Fig. C: Disassembly