Drieaz PHD 200 User manual

07-01913C F515 2014-02 Warranty 07-01651 1 Dri-Eaz Products, Inc.
Owner’s Manual
PHD 200 Dehumidifier
Model F515
DRI-EAZ PRODUCTS, INC.
15180 Josh Wilson Road, Burlington, WA 98233
Phone: [phone] Fax: [phone] www.EnvironmentsHQ.com
The Dri-Eaz®PHD 200 Dehumidifier reduces humidity in enclosed environments by removing water vapor
from the air. The PHD 200 is ideal for crawlspace drying, humidity control and other applications requiring
high-performance dehumidification. (Not intended for professional water damage restoration.)
Patents: http://www.LBpatents.com
READ AND SAVE THESE INSTRUCTIONS
Read and understand manual before operating.
WARNING! Do not alter or modify your PHD 200 in
any way. Use only replacement parts authorized by
Dri-Eaz Products, Inc. Modifications or use of unap-
proved parts could create a hazard and will void
your warranty. Contact your authorized Dri-Eaz dis-
tributor for assistance.
WARNING! Electric shock hazard, rotating fan, hot
surface hazards. Unplug unit before opening cover
for cleaning or servicing.
WARNING! Unit must be grounded.
•Keep motor and wiring dry. Keep out of standing wa-
ter and do not install in area likely to be subject to
water intrusion. Do not expose to rain, water or
snow.
•Insert three-prong plug on power cord into a match-
ing electrically grounded outlet. Do not use adapter.
Never cut off third prong.
•Do not use an extension cord.
•To reduce the risk of fire or electric shock, do not
use this unit with any solid-state speed control de-
vice.
FIRE HAZARD
•Keep away from open flames and heat sources.
•Do not use or store where vapors from gasoline, sol-
vents, thinners or other flammable materials may be
present.
WARNING! Unplug unit before cleaning or servicing.
•Turn off unit and unplug before lifting or moving.
•Handle the unit carefully. Always operate the unit on
a stable, level surface. Do not drop, throw, or place
where it could fall. Rough treatment can damage the
unit, and may create a hazardous condition or void
the warranty.
•Inspect the power cord before use. If cord is dam-
aged, do not use. Always grasp the plug (not the
cord) to unplug.
•The unit must be operated on a 115V/60 Hz circuit
protected by a Ground Fault Circuit Interrupter
(GFCI) device.
•Do not attempt to repair the unit. For Authorized
Service Centers, call Dri–Eaz Service at 800-932-
3030.
BEFORE YOU BEGIN
Warranty registration
Visit warranty.drieaz.com to register your purchase.
Registration allows us to better assist you with using,
maintaining or servicing your equipment and to contact
you in case we have important safety information con-
cerning your Dri-Eaz product. If you determine service is
required, have your equipment model, serial number and
original proof of purchase available and call your distrib-
utor for assistance with obtaining a return material au-
thorization (RMA).
INTRODUCTION
The PHD 200 Dehumidifier reduces humidity in enclosed
structures by removing water vapor from the air. With
proper use, the PHD 200 can help to dry out damp struc-
tural materials, insulation, and contents, and maintain a
healthy level of humidity. Using the PHD 200 may also
prevent secondary damage caused by high humidity.
WARNING

07-01913C F515 2014-02 Warranty 07-01651 2 Dri-Eaz Products, Inc.
How the PHD 200 works
The PHD 200 refrigerant dehumidifier uses a fan to draw
moist air in and condenses it into water that collects in a
tray and is automatically pumped out through a drain
hose. The PHD 200 is preset to automatically maintain a
50% RH level. To change this setting, see “Humidistat
Mode” below. Note: Unit automatically shuts off below
40% RH.
Features:
•Automatic humidistat to set and maintain desired
humidity level.
•Recessed handles for easy positioning in confined
spaces.
•Quiet operation and low power consumption.
CONTROLS AND OPERATING IN-
STRUCTIONS
Set unit upright
NOTICE: Always store, transport, and use the unit in
a horizontal position. If the unit is ever placed in a
vertical position, return it to the horizontal position
and let it stand for at least 30 minutes before turning
it on.
Positioning a Dehumidifier
For best results, operate your dehumidifiers in an en-
closed area. Place your dehumidifier away from obstruc-
tions, and keep it away from anything that could block
airflow into and out of the unit. For more information
about creating an optimum drying environment, contact
Dri-Eaz at 800-932-3030.
TIP: Before installing in a crawlspace or other difficult to
access location, plug in the unit and run it for approxi-
mately half an hour to ensure proper operation.
Set up drain hose
The PHD 200 condensate pump connects to a 20 ft. (6
m) plastic drain hose equipped with a quick-connect fit-
ting for quick attachment to the unit. To set up the hose,
unwrap the entire hose and place the unattached end in
a sink, drain, bucket or outdoors – anywhere that water
can drain out safely. Connect the other end of the hose
to the PHD 200. If you use a bucket or other container
for water collection, check it regularly to prevent over-
flows.
NOTICE: Uncoil and straighten the entire drain hose. Do
not leave any part of the hose coiled and do not place
the end of the hose higher than 3 ft. (1 m) above the bot-
tom of the unit. Also check for kinks or other obstructions
that might restrict the flow of water. Obstructions may
cause a water backup and result in overflows.
Plug in electrical cord
The PHD 200 should be plugged into a GFCI-protected
115 volt outlet rated for at least 15amps. Always plug
the cord firmly into the unit first, and then plug the other
end into a suitable outlet.
Startup display and normal display modes
When unit is first plugged in to AC power, the control
panel display will briefly cycle through a series of
readouts. This is part of the unit’s self-diagnosis proce-
dure and no user intervention is required.
Turn the unit on
The control panel on the PHD 200 dehumidifier has a
display and a touchpad with four keys. Press the
ON/OFF to turn the unit on. The unit will now go through
a compressor delay countdown (up to sixty seconds in
duration) and a self diagnostics process.
Once the compressor delay countdown and self-
diagnostics are complete, the display will switch to nor-
mal display mode.
UNIT ON 00 HRS
INLET 00°F / INLET 00%
The first line of the display shows the total number of
hours the unit has been in operation. This value may be
reset to zero to track job hours (see “Job Hours Reset”
below). The second line of the display alternates be-
tween inlet temperature and inlet humidity.
Fig. A: Parts Identification
Condensate
drain quick-
connect
Air inlet
Control
panel
Air outlet
Power
socket
Remove/Insert
air filter here.
Temp/RH
sensor

07-01913C F515 2014-02 Warranty 07-01651 3 Dri-Eaz Products, Inc.
CONTROL PANEL
ON/OFF
DISPLAY
DISPLAY
MENU
MENU SE-
LECTION /
UP KEY
PURGE PUMP
User Settings Menu
A number of display settings may be changed by the
user. System information can also be displayed. These
items are accessed by pressing DISPLAY MENU.
Each press of the key will display the next parameter.
When you reach the parameter you wish to adjust, press
MENU SELECTION to increase the value. Press
DISPLAY MENU again to accept the setting and re-start
the display cycle. If no keys are selected for 5 minutes
the display will automatically reset and return to the
normal display mode.
Note that only menu items followed by a greater-than
symbol (>) may be adjusted.
All settings and modes are discussed in detail in Control
Panel Guide, below.
Error messages
If the PHD 200 onboard diagnostics discover a problem,
the unit will display an error message. See “System
Messages,” p. 6 for an explanation of each message.
Control Panel Guide
ON/OFF. Press to turn the unit on or off. When the
machine is turned on, the display normally reads
PLEASE WAIT COMP. DELAY and performs a numeral
countdown for a maximum of 60 seconds to 0. This de-
lay allows time for refrigerant pressures to equalize for
easier starting. Once the unit completes the compressor
delay, the display shows UNIT ON XX HRS and cycles
between INLET XX°F and INLET XX%. NOTE: If no
compressor delay countdown is displayed, a delay is not
necessary and the machine will begin operation immedi-
ately.
DISPLAY MENU. Press to cycle through the display
of additional dehumidifier conditions and User Settings.
To return to the main menu, press the ON/OFF key
once.
MENU SELECTION. Press to change the values of
the "User Defined" settings. The MENU SELECTION
key acts as the UP key for adjusting the setpoint for Hu-
midistat mode operation. See User Settings Menu (be-
low) for details.
PURGE. Press to empty water from the condensate
pump reservoir. The display will read PUMP PURGING
with a numeral countdown. NOTE: During normal opera-
tion, the pump purges automatically every twenty
minutes, or whenever the reservoir is full.
Changing settings and viewing system information
Display setting changes and system information can be
accessed by pressing DISPLAY MENU. Each press
of the key will display the next parameter (see list be-
low). When you reach the parameter you wish to adjust,
press MENU SELECTION to increase the value.
Press DISPLAY MENU again to accept the setting
and re-start the display cycle. If no keys are selected for
5 minutes the display will automatically reset and return
to the normal display mode.
Note that only menu items followed by a greater-than
symbol (>) may be adjusted.
JOB HOURS
RESET? >
Press MENU SELECTION to reset hours to zero.
NOTE: When in Humidistat mode, the unit will display
HUMIDISTAT on the top line during normal operation
rather than JOB HOURS.
LIFE HOURS
00 HRS
Shows total unit operating hours. Value cannot be modi-
fied.
INLET OUTLET
00° 00% 00° 00%
Shows current temperature and RH of inlet and outlet.
ON/OFF
Press and release to turn unit on
or off.
DISPLAY MENU
Press to select next item in
menu. Menu item will show in
display.
MENU SELECTION /
UP KEY
Press to toggle or select values in
menu displayed.
PURGE PUMP
Press and release to start purge.
Display will count down seconds
remaining until purge is com-
plete.

07-01913C F515 2014-02 Warranty 07-01651 4 Dri-Eaz Products, Inc.
Normal Operation
The PHD 200 is preset to automatically maintain a 50%
RH level. To change this setting, see “Humidistat Mode”
below. Note: Unit automatically shuts off below 40% RH.
Humidistat Mode
HUMIDISTAT MODE
ON/OFF >
In ON mode, unit will maintain the humidistat setpoint
(see below). Press MENU SELECTION to toggle be-
tween ON and OFF. NOTE: When in Humidistat mode,
the unit will display HUMIDISTAT on the top line during
normal operation rather than JOB HOURS.
HUMIDISTAT
SETPOINT 00% >
Sets humidity level when unit is in Humidistat Mode.
Press MENU SELECTION to change RH value. Each
press of the button increases the setting by 5% incre-
ments, cycling through 90%RH and starting again at
40%RH.
TEMP UNITS
F° >
Shows current temperature scale. Press MENU SE-
LECTION to select Fahrenheit or Centigrade scale.
LANGUAGE
ENGLISH >
Shows current display panel language. Press MENU
SELECTION to select Spanish, German, French or Eng-
lish.
COIL TEMP
00°F
Displays the cold (evaporator) coil temperature.
SENSOR ID >
00000000
This function is not used on the PHD 200.
COMPRSSR CURRENT
0.0 A
Shows compressor current draw in amps.
AT THE END OF THE JOB
To reduce the possibility of drips when moving the unit,
follow these additional steps to ensure that all water is
removed from the unit.
NOTICE: To ensure the condensate tank empties com-
pletely while purging, make sure the unit is positioned
horizontally on a flat surface.
1. If the unit is in a defrost cycle, wait until the unit has
returned to normal operating mode before proceeding.
To check, review the control panel. The control panel will
show one of the following:
Defrost in progress:
UNIT ON 00 HRS
DEFROST XX
Display mode when unit is in defrost mode. XX indicates
the minutes remaining on the defrost cycle.
Shutdown Sequence
WAIT FOR
DEFROST XX
Display mode when unit is in defrost and is powered
down by the user. Unit will complete the defrost cycle to
remove any built-up ice and then purge the pump. XX
indicates the minutes remaining on the defrost cycle.
Normal Display:
UNIT ON 00 HRS
INLET XX° F
Wait until the control shows the normal display before
proceeding.
2. Gently rock the machine to ensure any water remain-
ing on interior surfaces falls into the sump area.
3. Press the PURGE key. When the purge cycle is
complete, turn the unit off.
4. Remove the external drain hose and drain it carefully
before storing it.
5. Unplug power cord from power supply and from base
of the machine.
TRANSPORTATION AND STORAGE
NOTICE: Handle the unit carefully. Do not drop, throw,
or place the unit where it could fall. Rough treatment can
damage this equipment and may create a hazardous
condition or void warranty.
•Do not expose the control panel to moisture, snow
or rain.
•Protect from freezing.
•Store and transport securely to avoid any damaging
impact to internal parts.
•Secure during transport to prevent sliding and pos-
sible injury to vehicle occupants.
MAINTENANCE SCHEDULE
WARNING! ELECTRIC SHOCK HAZARD. Unplug unit
before cleaning or servicing.
WARNING: Risk of dust and contaminants exposure.
Use of respirator mask and gloves is recommended. If
unit has been exposed to potentially dangerous contam-
inants, clean thoroughly and sanitize before reuse.

07-01913C F515 2014-02 Warranty 07-01651 5 Dri-Eaz Products, Inc.
NOTICE: The unit is fitted with sensitive electronic sen-
sors. Protect the sensors and their lead wires from dam-
age and do not expose them to water or cleaning solu-
tion.
The following tools and supplies are needed to
complete the maintenance procedures described in
this manual:
Philips screwdriver
10 mm wrench
6 mm hex bit
¼ in. nut driver
Cleaning cloths
HEPA vacuum cleaner with soft brush nozzle and
crevice nozzle.
Recommended
Cordless drill, small knife, small-jaw pliers, coil clean-
ing solution, rotomolded housing cleaning solution.
Before each use
Inspect the electrical cord for damage. Look for fray-
ing, cuts, etc. Replace the cord if you find any damage.
Inspect filter. The PHD 200 filter should be replaced
when the accumulation of dust is visible.
Monthly
Inspect and clean coils and interior surfaces. In nor-
mal use, dust can accumulate and can restrict airflow,
reducing performance and causing the unit to overheat.
Clean when dust accumulation is visible. Remove grills
and cover as shown in Fig. B. Use a vacuum cleaner
with a brush tool and a soft cloth to remove any debris.
Take care not to damage any interior components.
To maintain appearance, wipe interior and exterior sur-
faces with a damp cloth. For deep cleaning and a last-
ing, protective shine, use an automotive interior cleaner.
As Needed
Clean pump check valve and basin. If the unit displays
the message “ER9 PUMP BLOCKED CHECK PUMP &
HOSE”, the pump check valve and pump basin may
need to be cleaned. Remove grills and cover as shown
in Fig. B. Remove screws from pump base and lift out
pump. Wipe out pump basin with a damp cloth. Unthread
barbed fitting with check valve and rinse fitting and
check valve with clean water. Reinstall barbed fitting into
pump. Do not overtighten. Reinstall pump on base. Re-
install cover and grills.
Clean coils. With the cover removed, inspect both coils.
If excessive dust and debris is present, vacuum thor-
oughly and/or clean with coil cleaner.
Remove the 4 screws
from housing and 2
top screws each from
inlet and outlet grills
and lift off cover.
Fig. B: Disassembly for Cleaning

07-01913C F515 2014-02 Warranty 07-01651 6 Dri-Eaz Products, Inc.
System messages
The PHD 200 control system constantly monitors internal operating conditions. If the system detects a problem, it will pro-
duce an error (“ER”) message. If the display shows an ER message, first unplug the unit and then plug it back in. This will
usually reset the electronics, and the unit will begin operating normally. If the error message reappears, refer to the expla-
nation and solution shown below. If this still does not fix the problem, contact your local authorized service center or call
the Dri-Eaz Service Department at 800-932-3030.
NOTE: The message “POWER FAILURE” is not a system error. When this message is displayed, it indicates that
power to unit was interrupted and then restored. To clear the message, press the MENU SELECTION key.
CONTROL PANEL
MESSAGE EXPLANATION AND SOLUTION
ER1 CONTACT SERVICE
CENTER
Voltage error. Confirm that unit is connected to a suitable AC power supply and that the
circuit is not overloaded. If supply is correct, the electronic control panel may require
replacement. If error persists, contact service.
ER2 CONTACT SERVICE
CENTER Control panel error. The electronic control panel may require replacement. If error per- sists, contact service.
ER3 CONTACT SERVICE
CENTER Unit in defrost too long. Check defrost sensor cable for proper connection. If error per- sists, sensor assembly may require replacement. Contact service.
ER4 √ DEFROST SENSOR
CONNECT
– alternate message –
ER4 √ OUTLET SENSOR
CONNECT
Sensor error. Check defrost sensor cable for proper connection. If error persists, sensor
assembly may require replacement. Contact service.
ER5 √ SENSOR
CONNECTION ON BD Check inlet Temp/RH sensor for proper connection. If error persists, contact service.
ER6 CONTACT
SERVICE CENTER High voltage error. The high voltage board may require replacement. If error persists, contact service.
ER7 INVALID
MODEL SETTING Control board DIP switch settings or firmware version may be incorrect. If error persists, contact service. Service may ask you to verify DIP switch settings.
ER8 BUTTON STUCK √
ALL BUTTONS Press each membrane key and check for proper operation. If a key doesn’t function, or if the error persists, the membrane overlay may require replacement. Contact service.
ER9 PUMP BLOCKED √
CHECK PUMP & HOSE
Check for obstructions in drain hose. If clogged, remove hose from unit and blow hose
out with compressed air. Inspect and clean the pump check valve and pump basin. See
“Clean pump check valve and basin” p. 5.

07-01913C F515 2014-02 Warranty 07-01651 7 Dri-Eaz Products, Inc.
TROUBLESHOOTING
FAULT CAUSE SOLUTION
Water drips out
when moving unit Unit was unplugged before purging was complete. Purge unit before moving. See “At the End of the Job,” p. 4.
Unit does not
operate Unit not switched on. No power to machine.
Switch unit on.
Plug in unit; check power cord connection at wall outlet and at
base of unit.
Unit operating,
but room not dry
Not enough time to dry.
Poor air movement in room.
Excessive moist air infiltration.
Allow more time for drying.
Increase air movement with air movers.
Seal off area to reduce infiltration.
Unit collects too
little water
Room air is dry.
Room temperature is too low.
Filter is clogged.
Coils are clogged.
Confirm humidity level with hygrometer.
Increase room temperature.
Check filter. Clean or replace as necessary.
Check coils. Clean as necessary.
If the problem you are experiencing is not listed here, call your local distributor or contact
our Service Department toll-free at 800-932-3030 for further assistance.
SPECIFICATIONS
Name
PHD 200 Dehumidifier
Model F515
Dimensions (W × H × D) 12.5 × 17.6 × 21.5 in.
31.8 × 44.7 × 130.8 cm
Weight (w/ cord & hose) 65 lbs. | 29.5 kg
Amps 6.2 amps at 80°F/60% RH
Power 115V / 60Hz
Air movement 180 CFM | 5.4 CMM
Water removal
75 pts/day | 35 L/day
at 80°F/60% RH (AHAM)
134 pts/day | 63 L/day
at 90°F/90% RH
Operating temperature range 45–100°F | 7–38°C
Specifications are subject to change without notice. Some values
may be approximate.
PARTS INCLUDED
20 ft. (6 m) of drain hose with quick-connect fitting.
6 ft. (1.8 m) detachable power cord.
1 disposable mesh air filter (F527)
Optional
Joist Mounting Kit (F525)
Duct Attachment Kit (F530)
ADDITIONAL PRODUCT INFORMATION and current
documentation is available at
www.EnvironmentsHQ.com.
FOR PARTS AND SERVICE CALL YOUR LOCAL
DISTRIBUTOR or Dri-Eaz at 800-932-3030.
Visit warranty.DriEaz.com and register your purchase to
ensure you receive any important product releases.

07-01913C F515 2014-02 Warranty 07-01651 8 Dri-Eaz Products, Inc.
Manual del usuario
Deshumidificador PHD 200
Modelo F515
DRI-EAZ PRODUCTS, INC.
15180 Josh Wilson Road, Burlington, WA 98233
Teléfono: 800-932-3030 Fax: [phone] www.EnvironmentsHQ.com
El deshumidificador Dri-Eaz®PHD 200 reduce la humedad en ambientes cerrados al eliminar el vapor de
agua del aire. El PHD 200 es ideal para el secado espacio de acceso, control de humedad y otras aplica-
ciones que requieren deshumidificación de alto rendimiento. (No está diseñado para la restauración de
daños de agua profesional.)
Patentes: http://www.LBpatents.com
LEA Y GUARDE ESTAS INSTRUCCIONES
Lea y entienda el manual antes de operar el des-
humidificador.
¡ADVERTENCIA! No altere ni modifique su PHD 200
de ninguna forma. Utilice solamente las piezas de
repuesto autorizadas por Dri-Eaz Products, Inc. Las
modificaciones o el uso de piezas no autorizadas
podrían generar riesgos y anular la garantía. Pónga-
se en contacto con su distribuidor Dri-Eaz autoriza-
do para obtener ayuda.
¡ADVERTENCIA! Peligro de choque eléctrico, venti-
lador giratorio, riesgos por superficies calientes.
Desconecte la unidad antes de abrir la cubierta para
limpiarla o darle mantenimiento.
¡ADVERTENCIA! La unidad debe estar conectada a
tierra.
•Mantenga el motor y el cableado secos. Mantenga
la unidad lejos del agua estancada y no la instale en
zonas que puedan verse sometidas a entrada de
agua. No exponga el deshumidificador a la lluvia,
agua o nieve.
•Inserte el contacto de tres clavijas del cable de ali-
mentación a un tomacorriente conectado a tierra.
No use un adaptador. Nunca corte la tercera clavija.
•No utilice un cable de extensión.
•Para reducir el riesgo de incendio o descarga eléc-
trica, no use esta unidad con un dispositivo de con-
trol de velocidad de estado sólido.
PELIGRO DE INCENDIO
•Mantenga la unidad apartada de flamas abiertas y
fuentes de calor.
•No la utilice ni la almacene donde haya vapores de
gasolina, solventes, diluyentes u otros materiales in-
flamables.
¡ADVERTENCIA! Desconecte la unidad antes de lim-
piarla o darle mantenimiento.
•Apague la unidad y desconéctela antes de levantar-
la o moverla.
•Maneje la unidad con cuidado. Opere siempre la
unidad sobre una superficie estable y nivelada. No
la deje caer, no la tire ni la coloque donde pueda
caerse. Un trato brusco puede dañar la unidad y
puede generar una condición peligrosa o anular la
garantía.
•Inspeccione el cable de alimentación antes de utili-
zar la unidad. Si el cable está dañado, no utilice la
unidad. Sujete siempre la clavija (no el cable) para
desconectarla.
•La unidad debe operarse en un circuito de 115V/60
Hz protegido por un dispositivo interruptor de circui-
to por falla en tierra (GFCI, por sus siglas en inglés).
•No intente reparar la unidad. Para consultar una lis-
ta de los Centros de Servicio Autorizados, llame al
Servicio de Dri-Eaz al 800-932-3030.
ANTES DE COMENZAR
Registro de la garantía
Visite warranty.drieaz.com para registrar su compra. El
registro nos permite ayudarle mejor con el uso, mante-
nimiento o servicio de su equipo, y comunicarnos con
usted en caso de debamos proporcionarle información
de seguridad importante acerca de su producto Dri-Eaz.
Si usted considera que la unidad necesita recibir servi-
cio, tenga a la mano la información sobre el modelo de
su equipo, el número de serie y el comprobante de
ADVERTENCIA

07-01913C F515 2014-02 Warranty 07-01651 9 Dri-Eaz Products, Inc.
compra original, y llame a su distribuidor para que le
ayude a obtener una autorización de devolución de ma-
teriales (RMA, por sus siglas en inglés).
INTRODUCCIÓN
El deshumidificador PHD 200 reduce la humedad en
entornos cerrados estructurales al eliminar el vapor de
agua del aire. Con el uso apropiado, el PHD 200 puede
ayudar a secar materiales estructurales, aislamiento y
contenido húmedos, así como a mantener un nivel salu-
dable de humedad. El uso del PHD 200 también puede
evitar daños secundarios causados por el exceso de
humedad.
Funcionamiento del PHD 200
El deshumidificador por refrigeración PHD 200 utiliza un
ventilador para extraer el aire húmedo y condensarlo en
agua, la cual se acumula en una bandeja y se bombea
de forma automática hacia afuera a través de una man-
guera de desagüe. El PHD 200 está preconfigurado pa-
ra mantener automáticamente un nivel de humedad rela-
tiva del 50%. Para cambiar esta configuración, consulte
"Modo de humedad con" más adelante. Nota: La unidad
se apaga automáticamente por debajo del 40% de
humedad relativa.
Características:
•Modo de humidistato automático para establecer y
mantener el nivel de humedad deseado.
•Manijas empotradas para facilitar su colocación en
espacios reducidos.
•Funcionamiento silencioso y de bajo consumo de
energía.
CONTROLES E INSTRUCCIONES DE
OPERACIÓN
Coloque la unidad en posición vertical
AVISO: Siempre almacene, transporte y utilice la
unidad en posición horizontal. Si la unidad llegara a
colocarse en posición vertical, póngala en posición
horizontal de nuevo y déjela reposar durante al me-
nos 30 minutos antes de encenderla.
Ubicación del deshumidificador
Para obtener los mejores resultados, utilice los des-
humidificadores en un área cerrada. Coloque el des-
humidificador lejos de obstrucciones y manténgalo ale-
jado de cualquier objeto que pueda bloquear el flujo de
aire dentro y fuera de la unidad. Para obtener más in-
formación acerca de cómo crear un ambiente de secado
óptimo, comuníquese con Dri-Eaz al 800-932-3030.
CONSEJO: Antes de instalar la unidad en un sótano de
poca altura o cualquier otro lugar de difícil acceso, co-
necte la unidad y déjela encendida durante aproxima-
damente media hora para garantizar que funcione co-
rrectamente.
Configuración de la manguera de desa-
güe
La bomba de condensado del PHD 200 se conecta a
una manguera de desagüe de plástico que mide 20 pies
(6 m) y cuenta con una conexión de acoplamiento rápido
para que pueda conectarla con rapidez a la unidad. Para
instalarla, desenrolle toda la manguera y coloque el ex-
tremo suelto en un lavabo, desagüe, cubo o al aire libre
(en cualquier lugar donde el agua pueda drenarse de
forma segura). Conecte el otro extremo de la manguera
al PHD 200. Si utiliza un cubo u otro recipiente para re-
coger el agua, revíselo con regularidad para evitar que
el agua se derrame.
AVISO: Desenrolle y enderece toda la manguera de
desagüe. No deje ninguna parte de la manguera enro-
llada ni coloque el extremo de la manguera a 3 pies (1
m) por encima de la parte inferior de la unidad. También
vea si hay torceduras u otras obstrucciones que podrían
restringir el flujo de agua. Las obstrucciones pueden
provocar una retención del agua y ocasionar derrames.
Conecte el cable eléctrico
El PHD 200 debe conectarse a un tomacorriente de 115
voltios con protección de GFCI especificado por lo me-
nos para 15amperios. Siempre conecte firmemente el
cable en la unidad primero y luego conecte el otro ex-
tremo a un tomacorriente adecuado.
Pantalla de inicio y modos de visualización norma-
les
Cuando la unidad se conecta por primera vez en la ali-
mentación de corriente alterna (CA), la pantalla del pa-
nel de control mostrará brevemente una serie de lectu-
ras en ciclo. Esto es parte del procedimiento de autodia-
Imagen A: Identificación de las piezas
Conexión
rápida del
desagüe de
condensa-
ción
Entrada
de aire
Panel de
control
Salida de
aire
Tomaco-
rriente
Retire o inser-
te el filtro de
aire aquí.
Sensor de
tempera-

07-01913C F515 2014-02 Warranty 07-01651 10 Dri-Eaz Products, Inc.
PANEL DE CONTROL
ON/OFF
PANTALLA
DISPLAY
MENU (MENÚ
DE PANTA-
LLA)
MENU SELECTION /
UP KEY (SELEC-
CIÓN DE MENÚS /
FLECHA HACIA
ARRIBA)
BOMBA DE
PURGADO
gnóstico de la unidad y no se requiere ninguna interven-
ción del usuario.
Encienda la unidad
El panel de control del deshumidificador PHD 200 tiene
una pantalla y un panel táctil con cuatro botones. Pre-
sione el botón ON/OFF (ENCENDIDO / APAGADO)
para encender la unidad. La unidad realizará un conteo
regresivo de retardo del compresor (de hasta sesenta
segundos de duración) y un proceso de autodiagnóstico.
Una vez que la cuenta regresiva del compresor y el au-
todiagnóstico se hayan completado, la pantalla cambiará
al modo de visualización normal.
UNIT ON 00 HRS (UNIDAD ENCEN-
DIDA 00 HRS)
INLET 00°F / INLET 00% (ENTRADA
00° F / ENTRADA 00%)
La primera línea de la pantalla muestra el número total
de horas que la unidad ha estado en operación. Este
valor puede restablecerse a cero para dar seguimiento a
las horas de trabajo (vea “Restablecimiento de horas de
trabajo” a continuación). La segunda línea de la panta-
lla muestra alternadamente la temperatura de entrada y
la humedad de entrada.
Menú de configuraciones del usuario
El usuario puede cambiar algunas configuraciones de la
pantalla. También se puede mostrar la información del
sistema. Se puede tener acceso a estos elementos pre-
sionando DISPLAY MENU (MENÚ DE PANTALLA).
Con cada pulsación del botón se mostrará el siguiente
parámetro. Cuando llegue al parámetro que quiera ajus-
tar, presione MENU SELECTION (SELECCIÓN DE
MENÚS) para aumentar el valor. Presione DISPLAY
MENU (MENÚ DE PANTALLA) de nuevo para aceptar
la configuración y volver a iniciar el ciclo de visualiza-
ción. Si no se selecciona ningún botón durante 5 minu-
tos, la pantalla regresará automáticamente al modo de
visualización normal.
Tenga en cuenta que sólo se pueden ajustar los ele-
mentos del menú seguidos del símbolo mayor que ( >).
Todos los ajustes y modos se describen con detalle en
la Guía del panel de control, que se encuentra más ade-
lante.
Mensajes de error
Si el diagnóstico incorporado al PHD 200 detecta un
problema, la unidad mostrará un mensaje de error. Con-
sulte “Mensajes del sistema” en la pág. 6 para ver una
explicación de cada mensaje.
Guía del panel de control
ON/OFF (ENCENDIDO / APAGADO). Presione el
botón ON/OFF para encender o apagar la unidad.
Cuando el equipo está encendido, la pantalla indica
normalmente PLEASE WAIT COMP. DELAY (ESPERE
EL RETARDO DEL COMPRESOR) y realiza una cuenta
regresiva desde un máximo de 60 segundos hasta 0.
Este retardo da tiempo para que se iguale la presión del
refrigerante con el fin de facilitar el arranque. Una vez
que haya transcurrido el retardo del compresor, la pan-
talla mostrará UNIT ON XX HRS (UNIDAD ENCENDI-
DA XX HORAS) y alternará entre INLET XX°F (ENTRA-
DA XX° F e INLET XX% (ENTRADA XX%). NOTA: Si no
aparece ninguna cuenta regresiva de retardo del com-
presor, el retardo no es necesario y la máquina comen-
zará a funcionar de inmediato.
DISPLAY MENU (MENÚ DE PANTALLA). Presione
para alternar entre la visualización de las condiciones
adicionales del deshumidificador y la configuración del
usuario. Para volver al menú principal, presione el botón
ON/OFF (ENCENDIDO / APAGADO) una sola vez.
MENU SELECTION (SELECCIÓN DE MENÚS).
Presione para cambiar los valores de los ajustes "User
Defined" (definidos por el usuario). El botón de MENU
SELECTION (SELECCIÓN DE MENÚS) funciona como
tecla de flecha hacia arriba para ajustar el punto de ope-
ración del funcionamiento en el modo de humidistato.
Consulte la sección Menú de configuración del usuario
(más adelante) para ver más detalles.
PURGE (PURGA). Presione para vaciar el agua del
depósito de la bomba de condensado. En la pantalla
aparecerá PURGING PUMP (PURGANDO BOMBA) con
un número de cuenta regresiva. NOTA: Durante el fun-
ON/OFF (ENCENDIDO /
APAGADO)
Presione y suelte para encender
o apagar la unidad.
DISPLAY MENU (MENÚ DE
PANTALLA)
Presione para seleccionar el
siguiente elemento del menú. El
elemento del menú se mostrará
en la pantalla.
MENU SELECTION /
UP KEY (SELECCIÓN DE
MENÚS / FLECHA HACIA
ARRIBA)
Presione para cambiar o selec-
cionar los valores en el menú
desplegado.
BOMBA DE PURGADO
Presione y suelte para empezar a
purgar. La pantalla mostrará una
cuenta regresiva de los segundos
que falten para que se complete
la purga.