DSPM UniMeasure HX-VP420 Series User manual

AlternateWire Rope Exit
E1 E2 E3
NOTE
Mount with Ø.25 or M6
Socket Head Cap Screws.
AlternateWire Rope Exit
NOTE
Mount with Ø.50 or M12 Socket Head Cap Screws.
RANGE “A” “B” “C”
2”, 10” 1.12 (28.4) 1.79 (45.5) 1.21 (30.7)
3”, 15”, 30” .96(24.4) 1.95 (49.5) 1.37 (34.8)
4”, 20”, 40” .80 (20.3) 2.11 (53.6) 1.53 (38.9)
5”, 25”, 50” .64 (16.3) 2.27 (57.7) 1.69 (42.9)
60” .49 (12.4) 2.42 (61.5) 1.84 (46.7)
80” .25 (6.4) 2.66 (67.6) 2.08 (52.8)
AlternateWire Rope Exit
Note: Dimensions in
brackets are millimeters.
Dimensional Information
HX-VP420 Series Installation Guide
Wiring and Circuit Diagram
Velocity
The tachometer is self energizing and requires
no input voltage.
shieldedcablebetweenthetransducerandthe
electrical interface. The shield of the cable
shouldbeopen at the transducerandgrounded
at the electrical interface.
With small blade type screwdriver (.105"
max. blade width X .023" max. blade thick-
ness), adjust the Zero and Span controls on
the transducer to set the 4 and 20 mA output
limits. Note: The Zero and Span controls
are somewhat interactive and may require
several iterations to obtain the desired zero
and maxi-
Model HX-VP420
The 4 to 20 mA output transducer is a 2-wire,
loop powered device. The transducer, power
supply, and current monitor must be connected
in series as illustrated above.
The minimum supply voltage is a function of
total loop resistance. It may be calculated using
the formula:
V(Min.)= (0.02 x Load Res.) + 9 VDC
It may also be determined from the accom-
panying graph, shown at right.
Whenmounting,insurethatthebaseplate of the
transducerisgrounded to earthground. Forbest
noise immunity, use twisted pair
mum settings. Extendthe transducer's cable (on
angular position transducers, rotate shaft) to the
desired zero position (must be within 0% to 30%
of range). Adjust the Zero control so that the
outputcurrentis4 mA.Thenextendthecable(on
angular position transducers, rotate shaft) to the
desired maximum position (must be within 80%
to 100% of range). Adjust the Span control for
maximum output current of 20 mA. Recheck the
zerosettingandadjustifnecessary.Recheckthe
Span setting and readjust if necessary.
Via Paolo Uccello 4 - 20148 Milano
Tel [phone] Fax [phone] [email protected] www.dspmindustria.it

AlternateWire Rope Exit
E1 E2 E3
NOTE
Mount with Ø.25 or M6
Socket Head Cap Screws.
AlternateWire Rope Exit
NOTE
Mount with Ø.50 or M12 Socket Head Cap Screws.
RANGE “A” “B” “C”
2”, 10” 1.12 (28.4) 1.79 (45.5) 1.21 (30.7)
3”, 15”, 30” .96(24.4) 1.95 (49.5) 1.37 (34.8)
4”, 20”, 40” .80 (20.3) 2.11 (53.6) 1.53 (38.9)
5”, 25”, 50” .64 (16.3) 2.27 (57.7) 1.69 (42.9)
60” .49 (12.4) 2.42 (61.5) 1.84 (46.7)
80” .25 (6.4) 2.66 (67.6) 2.08 (52.8)
AlternateWire Rope Exit
Note: Dimensions in
brackets are millimeters.
Dimensional Information
HX-VP510 Series Installation Guide
Wiring and Circuit Diagram
Velocity
The tachometer is self energizing and requires no input voltage.
Model HX-VP510 As shown in the diagram above, both commons on pins "B" and "C"
are connected together internally at the transducer, so that either a
3-wire or 4-wire connection to the transducer may be made.
With small blade type screwdriver (.105" max. blade width X .023"
max. blade thickness), adjust the Zero and Span controls on the
transducer to set zero output voltage and maximum output volt-
age. Note: The Zero and Span controls are somewhat interactive
and may require several iterations to obtain the desired zero and
maximum settings.
Extend the cable (on angular position transducers, rotate shaft) of
the transducer to the desired zero position (must be within 0% to
30% of range.) Adjust the Zero control so that the output voltage
is zero. Then extend the cable (on angular position transducers,
rotate shaft) to the desired maximum position (must be within 80%
to 100% of range.) Adjust the Span control for maximum output
voltage required (unit will adjust from 5 VDC to 10 VDC). Recheck
the zero setting and adjust if necessary. Recheck the Span setting
and readjust if necessary.
Excitation Voltage ..........4.9 to 30VDC
Excitation Current..........40 mAmax.
Output Impedance.........10 Ωmax.
Output Load...................5KΩmin.
Via Paolo Uccello 4 - 20148 Milano
Tel [phone] Fax [phone] [email protected] www.dspmindustria.it

Alternate Wire Rope Exit
E1 E2 E3
NOTE
Mount with Ø.25 or M6
Socket Head Cap Screws.
Alternate Wire Rope Exit
NOTE
Mount with Ø.50 or M12 Socket Head Cap Screws.
RANGE “A” “B” “C”
2”, 10” 1.12 (28.4) 1.79 (45.5) 1.21 (30.7)
3”, 15”, 30” .96(24.4) 1.95 (49.5) 1.37 (34.8)
4”, 20”, 40” .80 (20.3) 2.11 (53.6) 1.53 (38.9)
5”, 25”, 50” .64 (16.3) 2.27 (57.7) 1.69 (42.9)
60” .49 (12.4) 2.42 (61.5) 1.84 (46.7)
80” .25 (6.4) 2.66 (67.6) 2.08 (52.8)
Alternate Wire Rope Exit
Note: Dimensions in
brackets are millimeters.
Dimensional Information
HX-VP1010 Series Installation Guide
Wiring and Circuit Diagram
With small blade type screwdriver (.105" max. blade
width X .023" max. blade thickness), adjust the Zero
and Span controls on the transducer to set the zero
and maximum output voltages. Note: The Zero and
Span controls are somewhat interactive and may re-
quire several iterations to obtain the desired zero and
maximum voltage settings. Extend the transducer cable
(on angular position transducers, rotate shaft) to the
desired zero position (must be within 10% to 90% of
the total range). Adjust the Zero control to give a zero
voltage output. Then extend the cable (on angular posi-
tion transducers, rotate shaft) to the desired maximum
position in the direction of longest possible travel (either
positive or negative) from the zero position. To obtain
maximum output voltage magnitude this position must
lie within 50% to 100% of the longest possible travel.
Adjust the Span control to the output voltage magnitude
required (+ or - 10 VDC maximum). Recheck the zero
and span settings and readjust if necessary.
Position
See Table 1 at right for position input voltage.
Velocity
The tachometer is self energizing and requires no input
Model HX-VP1010
Position
Excitation Voltage ........ +15 & -15 VDC (±5%)
Output Impedance....... 1.0 Ωmax.
Output Load................. 5KΩmin.
Model HX-VP1010-xx-
Velocity
The tachometer is self energizing and
requires no input voltage.
Option
Designator
SI 4.9 to 30 VDC
SI5 5 ±0.5 VDC
SI12 12 ±0.5 VDC
SI15 15 ±0.5 VDC
SI24 24 ±1.0 VDC
Input
Voltage
Via Paolo Uccello 4 - 20148 Milano
Tel [phone] Fax [phone] [email protected] www.dspmindustria.it